Commit 2aa1a536 authored by Frank Lars Zimdars's avatar Frank Lars Zimdars Committed by Bernd-Christian Renner
Browse files

small corrections

parent 156ca78e
...@@ -26,5 +26,3 @@ Erledigt: ...@@ -26,5 +26,3 @@ Erledigt:
- Die Testpoints sollten für den TXB unterschiedliche Farben haben (laut Text), habe sie aber nicht. - Die Testpoints sollten für den TXB unterschiedliche Farben haben (laut Text), habe sie aber nicht.
- Beim RX-auto-Test fehlte eine Beschreibung, was der eigentlich macht. - Beim RX-auto-Test fehlte eine Beschreibung, was der eigentlich macht.
- By pylib Verwendung für RX nur auf die Doku verweisen (das INSTALL File ist jetzt ja doppelt gemoppelt und deprecated, oder?) - By pylib Verwendung für RX nur auf die Doku verweisen (das INSTALL File ist jetzt ja doppelt gemoppelt und deprecated, oder?)
...@@ -93,8 +93,7 @@ The Mainboard has six LEDs indicating the status of the modem. ...@@ -93,8 +93,7 @@ The Mainboard has six LEDs indicating the status of the modem.
</table> </table>
!!! info "Info" !!! info "Info"
The indicator levels are rough estimates based on a 3S LiPo battery with 12.4 V nominal rating. The indicator levels are rough estimates based on a 3S LiPo battery with 12.4 V nominal rating.
To change the values or behavior, consult tutorial [Customising the Firmware](/tutorial_firmware/#fw_batlevels). [A](/tutorial_firmware/#fw_batlevels)
## Connectors ## Connectors
......
...@@ -77,7 +77,7 @@ The values are represented by scaled integers. The value 0x4000 corresponds to a ...@@ -77,7 +77,7 @@ The values are represented by scaled integers. The value 0x4000 corresponds to a
<a name="fw_batlevels"></a> <a name="fw_batlevels"></a>
The modem firmware shows the batterie level through a LED blink code. At default the levels in the firmware are matched to a LiPo batterie (3 cell). The modem firmware shows the battery level through an LED blink code. The levels are based on a 3-cell LiPo battery.
Inside the file "batvoltage.c" the struct "batvolThresh" contains the values for the levels. The measured voltage is 200mV below the input voltage Inside the file "batvoltage.c" the struct "batvolThresh" contains the values for the levels. The measured voltage is 200mV below the input voltage
(reduced by the polarity protection diode). (reduced by the polarity protection diode).
...@@ -221,4 +221,4 @@ To set a breakpoint where the line in the cource code is optmised and not avaiab ...@@ -221,4 +221,4 @@ To set a breakpoint where the line in the cource code is optmised and not avaiab
Page last revised on: {{ git_revision_date }} Page last revised on: {{ git_revision_date }}
\ No newline at end of file
...@@ -10,7 +10,7 @@ nav: ...@@ -10,7 +10,7 @@ nav:
- Customize Hardware: hardware_custom.md - Customize Hardware: hardware_custom.md
- Test Hardware: hardware_check.md - Test Hardware: hardware_check.md
- Getting Started: - Getting Started:
- Firmware Installation and Updating: setup_fw.md - Compile and flash the firmware: setup_fw.md
- Connecting to the Modem with PyLib: setup_pylib.md - Connecting to the Modem with PyLib: setup_pylib.md
- Tutorial: - Tutorial:
- Hello, World!: tutorial_helloworld.md - Hello, World!: tutorial_helloworld.md
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment