diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt
index cd5e23912888cf4350750fe0adc908fb895e3d08..6794cdc96d8fdf44513a4ad2310fe67a2a93712d 100644
--- a/Documentation/devicetree/bindings/clock/at91-clock.txt
+++ b/Documentation/devicetree/bindings/clock/at91-clock.txt
@@ -62,7 +62,7 @@ Required properties for PMC node:
- interrupt-controller : tell that the PMC is an interrupt controller.
- #interrupt-cells : must be set to 1. The first cell encodes the interrupt id,
and reflect the bit position in the PMC_ER/DR/SR registers.
- You can use the dt macros defined in dt-bindings/clk/at91.h.
+ You can use the dt macros defined in dt-bindings/clock/at91.h.
0 (AT91_PMC_MOSCS) -> main oscillator ready
1 (AT91_PMC_LOCKA) -> PLL A ready
2 (AT91_PMC_LOCKB) -> PLL B ready
diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt
index 9fbbdb783a72d50600755a074cbc11cfba97f713..68ff2137bae7261e84409a472fbf432989fca0d6 100644
--- a/Documentation/devicetree/bindings/dma/ti-edma.txt
+++ b/Documentation/devicetree/bindings/dma/ti-edma.txt
@@ -29,6 +29,6 @@ edma: edma@49000000 {
dma-channels = <64>;
ti,edma-regions = <4>;
ti,edma-slots = <256>;
- ti,edma-xbar-event-map = <1 12
- 2 13>;
+ ti,edma-xbar-event-map = /bits/ 16 <1 12
+ 2 13>;
};
diff --git a/MAINTAINERS b/MAINTAINERS
index 764075dd8d618ce2088ff5be7b6d9fe02f4cef98..c596b74b29d532246b3646086c77381076ad3c15 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1893,14 +1893,15 @@ L: netdev@vger.kernel.org
S: Supported
F: drivers/net/ethernet/broadcom/bnx2x/
-BROADCOM BCM281XX/BCM11XXX ARM ARCHITECTURE
+BROADCOM BCM281XX/BCM11XXX/BCM216XX ARM ARCHITECTURE
M: Christian Daudt <bcm@fixthebug.org>
M: Matt Porter <mporter@linaro.org>
L: bcm-kernel-feedback-list@broadcom.com
-T: git git://git.github.com/broadcom/bcm11351
+T: git git://github.com/broadcom/mach-bcm
S: Maintained
F: arch/arm/mach-bcm/
F: arch/arm/boot/dts/bcm113*
+F: arch/arm/boot/dts/bcm216*
F: arch/arm/boot/dts/bcm281*
F: arch/arm/configs/bcm_defconfig
F: drivers/mmc/host/sdhci_bcm_kona.c
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index cb6811e5ae5a9a148321d4e667dc34cde9bc9846..7ad75b4e066358f5229d93d0d017c754a711ca32 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -144,7 +144,7 @@ edma: edma@49000000 {
compatible = "ti,edma3";
ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
reg = <0x49000000 0x10000>,
- <0x44e10f90 0x10>;
+ <0x44e10f90 0x40>;
interrupts = <12 13 14>;
#dma-cells = <1>;
dma-channels = <64>;
diff --git a/arch/arm/boot/dts/am3517.dtsi b/arch/arm/boot/dts/am3517.dtsi
index 788391f916844130d8d6cdb2722479163863a707..5a452fdd7c5d9711cec9f6d0196f90b0726fefc3 100644
--- a/arch/arm/boot/dts/am3517.dtsi
+++ b/arch/arm/boot/dts/am3517.dtsi
@@ -62,5 +62,21 @@ uart4: serial@4809e000 {
};
};
+&iva {
+ status = "disabled";
+};
+
+&mailbox {
+ status = "disabled";
+};
+
+&mmu_isp {
+ status = "disabled";
+};
+
+&smartreflex_mpu_iva {
+ status = "disabled";
+};
+
/include/ "am35xx-clocks.dtsi"
/include/ "omap36xx-am35xx-omap3430es2plus-clocks.dtsi"
diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts
index df8798e8bd255bbf789da0b44f5229b9f3dc80dd..a055f7f0f14ae5a3e080489c9c424bd37be0e1c0 100644
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@@ -117,6 +117,11 @@ &gpio4 {
status = "okay";
};
+&gpio5 {
+ status = "okay";
+ ti,no-reset-on-init;
+};
+
&mmc1 {
status = "okay";
vmmc-supply = <&vmmcsd_fixed>;
diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts
index 82f238a9063ffe47d10dbe083f136e1876f8efd2..3383c4b668035737e1812777fed34a03f5f9ef7c 100644
--- a/arch/arm/boot/dts/armada-370-db.dts
+++ b/arch/arm/boot/dts/armada-370-db.dts
@@ -67,6 +67,7 @@ ethernet@74000 {
i2c@11000 {
pinctrl-0 = <&i2c0_pins>;
pinctrl-names = "default";
+ clock-frequency = <100000>;
status = "okay";
audio_codec: audio-codec@4a {
compatible = "cirrus,cs42l51";
diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts
index 9378d3136b41d7b37f11abdf01186c019758f7f1..0451124e8ebf49af45b34072ae69a02a6fa133a9 100644
--- a/arch/arm/boot/dts/armada-375-db.dts
+++ b/arch/arm/boot/dts/armada-375-db.dts
@@ -79,6 +79,11 @@ sdio_st_pins: sdio-st-pins {
};
};
+ sata@a0000 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+
nand: nand@d0000 {
pinctrl-0 = <&nand_pins>;
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts
index 448373c4b0e534c1d2ce08592981f5d38bad39a8..90f0bf6f92715c7335072bda5b508e7800fa89a4 100644
--- a/arch/arm/boot/dts/armada-xp-db.dts
+++ b/arch/arm/boot/dts/armada-xp-db.dts
@@ -49,7 +49,7 @@ devbus-bootcs {
/* Device Bus parameters are required */
/* Read parameters */
- devbus,bus-width = <8>;
+ devbus,bus-width = <16>;
devbus,turn-off-ps = <60000>;
devbus,badr-skew-ps = <0>;
devbus,acc-first-ps = <124000>;
diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts
index 61bda687f782f65485f958adb8d8ec2822ebde35..0c756421ae6aa5f504b72898c16875bdaab5f8d3 100644
--- a/arch/arm/boot/dts/armada-xp-gp.dts
+++ b/arch/arm/boot/dts/armada-xp-gp.dts
@@ -59,7 +59,7 @@ devbus-bootcs {
/* Device Bus parameters are required */
/* Read parameters */
- devbus,bus-width = <8>;
+ devbus,bus-width = <16>;
devbus,turn-off-ps = <60000>;
devbus,badr-skew-ps = <0>;
devbus,acc-first-ps = <124000>;
@@ -146,22 +146,22 @@ phy3: ethernet-phy@3 {
ethernet@70000 {
status = "okay";
phy = <&phy0>;
- phy-mode = "rgmii-id";
+ phy-mode = "qsgmii";
};
ethernet@74000 {
status = "okay";
phy = <&phy1>;
- phy-mode = "rgmii-id";
+ phy-mode = "qsgmii";
};
ethernet@30000 {
status = "okay";
phy = <&phy2>;
- phy-mode = "rgmii-id";
+ phy-mode = "qsgmii";
};
ethernet@34000 {
status = "okay";
phy = <&phy3>;
- phy-mode = "rgmii-id";
+ phy-mode = "qsgmii";
};
/* Front-side USB slot */
diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
index 985948ce67b3271a65c9b4a413a99e7d255b12e7..5d42feb3104983a2ee9b21be33b59cc2e66a1bcd 100644
--- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
+++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
@@ -39,7 +39,7 @@ devbus-bootcs {
/* Device Bus parameters are required */
/* Read parameters */
- devbus,bus-width = <8>;
+ devbus,bus-width = <16>;
devbus,turn-off-ps = <60000>;
devbus,badr-skew-ps = <0>;
devbus,acc-first-ps = <124000>;
diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
index ce1375595e5f27117c37881bcafa5fc5805b1455..4537259ce5299baf8cf68978d7c2d106c5f67c32 100644
--- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
@@ -34,7 +34,7 @@ slot@0 {
};
spi0: spi@f0004000 {
- cs-gpios = <&pioD 13 0>;
+ cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
status = "okay";
};
@@ -79,7 +79,7 @@ slot@0 {
};
spi1: spi@f8008000 {
- cs-gpios = <&pioC 25 0>, <0>, <0>, <&pioD 16 0>;
+ cs-gpios = <&pioC 25 0>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
index e21dda0e8986574b2531c1675eca1b4de164822d..3be973e9889a2b0ef29cc45657ad6eeb056e7f5f 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@@ -10,7 +10,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
/ {
model = "Atmel AT91SAM9261 family SoC";
diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index 63e1784d272c556974023fcfd7d46ba7a0510e3d..92a52faebef77cd8eda572d11504c0f83362a428 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -8,7 +8,7 @@
#include "skeleton.dtsi"
#include <dt-bindings/pinctrl/at91.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi
index 9c2bff2252d0d078514348ab2bc92aad7ea5a6fb..6a1bf4ff83d5516dac0016ebc2bdd21d05565631 100644
--- a/arch/arm/boot/dts/imx53.dtsi
+++ b/arch/arm/boot/dts/imx53.dtsi
@@ -115,7 +115,7 @@ ipu: ipu@18000000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx53-ipu";
- reg = <0x18000000 0x080000000>;
+ reg = <0x18000000 0x08000000>;
interrupts = <11 10>;
clocks = <&clks IMX5_CLK_IPU_GATE>,
<&clks IMX5_CLK_IPU_DI0_GATE>,
diff --git a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
index 32c6fb4a11624c05756e4e2fe24b05c62c799667..b939f4f52d16a7c0edb677a86558bacd94fec831 100644
--- a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
+++ b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
@@ -30,6 +30,16 @@ chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk";
};
+ mbus {
+ pcie-controller {
+ status = "okay";
+
+ pcie@1,0 {
+ status = "okay";
+ };
+ };
+ };
+
ocp@f1000000 {
pinctrl@10000 {
pmx_usb_led: pmx-usb-led {
@@ -73,14 +83,6 @@ serial@12000 {
ehci@50000 {
status = "okay";
};
-
- pcie-controller {
- status = "okay";
-
- pcie@1,0 {
- status = "okay";
- };
- };
};
gpio-leds {
diff --git a/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi b/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
index aa78c2d11fe738fc843f716bd1a6f98ff1054a5b..e2cc85cc3b87e805a113489d3d95cf912d682224 100644
--- a/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
@@ -4,6 +4,16 @@
/ {
model = "ZyXEL NSA310";
+ mbus {
+ pcie-controller {
+ status = "okay";
+
+ pcie@1,0 {
+ status = "okay";
+ };
+ };
+ };
+
ocp@f1000000 {
pinctrl: pinctrl@10000 {
@@ -26,14 +36,6 @@ sata@80000 {
status = "okay";
nr-ports = <2>;
};
-
- pcie-controller {
- status = "okay";
-
- pcie@1,0 {
- status = "okay";
- };
- };
};
gpio_poweroff {
diff --git a/arch/arm/boot/dts/kirkwood-t5325.dts b/arch/arm/boot/dts/kirkwood-t5325.dts
index 7d1c7677a18f18c3fb1cc00463420545a5b6cb78..0bd70d928c69ba7f7798d1492f6ce3844af9d6ad 100644
--- a/arch/arm/boot/dts/kirkwood-t5325.dts
+++ b/arch/arm/boot/dts/kirkwood-t5325.dts
@@ -127,11 +127,6 @@ partition@4 {
i2c@11000 {
status = "okay";
-
- alc5621: alc5621@1a {
- compatible = "realtek,alc5621";
- reg = <0x1a>;
- };
};
serial@12000 {
diff --git a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
index f577b7df9a29e4f5f4e74ca86aef4b4ba61ceb87..521c587acaee9f679ab6f9200c5f8be8eee240e9 100644
--- a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
+++ b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
@@ -24,11 +24,10 @@ ethernet@gpmc {
compatible = "smsc,lan9221", "smsc,lan9115";
bank-width = <2>;
gpmc,mux-add-data;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <186>;
- gpmc,cs-wr-off-ns = <186>;
- gpmc,adv-on-ns = <12>;
- gpmc,adv-rd-off-ns = <48>;
+ gpmc,cs-on-ns = <1>;
+ gpmc,cs-rd-off-ns = <180>;
+ gpmc,cs-wr-off-ns = <180>;
+ gpmc,adv-rd-off-ns = <18>;
gpmc,adv-wr-off-ns = <48>;
gpmc,oe-on-ns = <54>;
gpmc,oe-off-ns = <168>;
@@ -36,12 +35,10 @@ ethernet@gpmc {
gpmc,we-off-ns = <168>;
gpmc,rd-cycle-ns = <186>;
gpmc,wr-cycle-ns = <186>;
- gpmc,access-ns = <114>;
- gpmc,page-burst-access-ns = <6>;
- gpmc,bus-turnaround-ns = <12>;
- gpmc,cycle2cycle-delay-ns = <18>;
- gpmc,wr-data-mux-bus-ns = <90>;
- gpmc,wr-access-ns = <186>;
+ gpmc,access-ns = <144>;
+ gpmc,page-burst-access-ns = <24>;
+ gpmc,bus-turnaround-ns = <90>;
+ gpmc,cycle2cycle-delay-ns = <90>;
gpmc,cycle2cycle-samecsen;
gpmc,cycle2cycle-diffcsen;
vddvario-supply = <&vddvario>;
diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi
index 22f35ea142c199082afdd8ba626bd7c5e0b6cd54..8f8c07da4ac148d550ae45cd3501d4a992f4e7c8 100644
--- a/arch/arm/boot/dts/omap2.dtsi
+++ b/arch/arm/boot/dts/omap2.dtsi
@@ -71,13 +71,6 @@ hdq1w: 1w@480b2000 {
interrupts = <58>;
};
- mailbox: mailbox@48094000 {
- compatible = "ti,omap2-mailbox";
- ti,hwmods = "mailbox";
- reg = <0x48094000 0x200>;
- interrupts = <26>;
- };
-
intc: interrupt-controller@1 {
compatible = "ti,omap2-intc";
interrupt-controller;
diff --git a/arch/arm/boot/dts/omap2420.dtsi b/arch/arm/boot/dts/omap2420.dtsi
index 85b1fb014c4314efe82eca9fcb7dfa7e482cb8d2..2d9979835f241f2153cd3d0b52c5c8b0b6c49559 100644
--- a/arch/arm/boot/dts/omap2420.dtsi
+++ b/arch/arm/boot/dts/omap2420.dtsi
@@ -125,6 +125,14 @@ msdi1: mmc@4809c000 {
dma-names = "tx", "rx";
};
+ mailbox: mailbox@48094000 {
+ compatible = "ti,omap2-mailbox";
+ reg = <0x48094000 0x200>;
+ interrupts = <26>, <34>;
+ interrupt-names = "dsp", "iva";
+ ti,hwmods = "mailbox";
+ };
+
timer1: timer@48028000 {
compatible = "ti,omap2420-timer";
reg = <0x48028000 0x400>;
diff --git a/arch/arm/boot/dts/omap2430.dtsi b/arch/arm/boot/dts/omap2430.dtsi
index d09697dab55e80063a737361c65138822bbdf828..42d2c61c9e2d7dc1851054a45ec305820cc8a9f4 100644
--- a/arch/arm/boot/dts/omap2430.dtsi
+++ b/arch/arm/boot/dts/omap2430.dtsi
@@ -216,6 +216,13 @@ mmc2: mmc@480b4000 {
dma-names = "tx", "rx";
};
+ mailbox: mailbox@48094000 {
+ compatible = "ti,omap2-mailbox";
+ reg = <0x48094000 0x200>;
+ interrupts = <26>;
+ ti,hwmods = "mailbox";
+ };
+
timer1: timer@49018000 {
compatible = "ti,omap2420-timer";
reg = <0x49018000 0x400>;
diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
index d00055809e31d79b9d1730c06efe02c7e2e6f747..25ba08331d8852e6701c96a4b9e8e54def19f0d8 100644
--- a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
+++ b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
@@ -10,18 +10,6 @@ cpu@0 {
cpu0-supply = <&vcc>;
};
};
-
- vddvario: regulator-vddvario {
- compatible = "regulator-fixed";
- regulator-name = "vddvario";
- regulator-always-on;
- };
-
- vdd33a: regulator-vdd33a {
- compatible = "regulator-fixed";
- regulator-name = "vdd33a";
- regulator-always-on;
- };
};
&omap3_pmx_core {
@@ -35,58 +23,34 @@ OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_1
hsusb0_pins: pinmux_hsusb0_pins {
pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
- OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
- OMAP3_CORE1_IOPAD(0x21a4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
- OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
- OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data0.hsusb2_data0 */
- OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
- OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
- OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data3 */
- OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data4 */
- OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data5 */
- OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data6 */
- OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
+ OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
+ OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
+ OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
+ OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
+ OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data0.hsusb2_data0 */
+ OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
+ OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
+ OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data3 */
+ OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data4 */
+ OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data5 */
+ OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data6 */
+ OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
>;
};
};
+#include "omap-gpmc-smsc911x.dtsi"
+
&gpmc {
ranges = <5 0 0x2c000000 0x01000000>;
- smsc1: ethernet@5,0 {
+ smsc1: ethernet@gpmc {
compatible = "smsc,lan9221", "smsc,lan9115";
pinctrl-names = "default";
pinctrl-0 = <&smsc1_pins>;
interrupt-parent = <&gpio6>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
reg = <5 0 0xff>;
- bank-width = <2>;
- gpmc,mux-add-data;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <186>;
- gpmc,cs-wr-off-ns = <186>;
- gpmc,adv-on-ns = <12>;
- gpmc,adv-rd-off-ns = <48>;
- gpmc,adv-wr-off-ns = <48>;
- gpmc,oe-on-ns = <54>;
- gpmc,oe-off-ns = <168>;
- gpmc,we-on-ns = <54>;
- gpmc,we-off-ns = <168>;
- gpmc,rd-cycle-ns = <186>;
- gpmc,wr-cycle-ns = <186>;
- gpmc,access-ns = <114>;
- gpmc,page-burst-access-ns = <6>;
- gpmc,bus-turnaround-ns = <12>;
- gpmc,cycle2cycle-delay-ns = <18>;
- gpmc,wr-data-mux-bus-ns = <90>;
- gpmc,wr-access-ns = <186>;
- gpmc,cycle2cycle-samecsen;
- gpmc,cycle2cycle-diffcsen;
- vddvario-supply = <&vddvario>;
- vdd33a-supply = <&vdd33a>;
- reg-io-width = <4>;
- smsc,save-mac-address;
};
};
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
index b97736d98a6427f087c11bd510909b1007f8c152..e2d163bf061975bff9ac5a6e83ecf6bf4ef98ed3 100644
--- a/arch/arm/boot/dts/omap3-igep.dtsi
+++ b/arch/arm/boot/dts/omap3-igep.dtsi
@@ -107,7 +107,7 @@ mmc2_pins: pinmux_mmc2_pins {
>;
};
- smsc911x_pins: pinmux_smsc911x_pins {
+ smsc9221_pins: pinmux_smsc9221_pins {
pinctrl-single,pins = <
0x1a2 (PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
>;
diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts
index 7abd64f6ae21465c9ac74b22563f8f828a5d684b..b22caaaf774ba710461fcabf395c121c0ccc0482 100644
--- a/arch/arm/boot/dts/omap3-igep0020.dts
+++ b/arch/arm/boot/dts/omap3-igep0020.dts
@@ -10,7 +10,7 @@
*/
#include "omap3-igep.dtsi"
-#include "omap-gpmc-smsc911x.dtsi"
+#include "omap-gpmc-smsc9221.dtsi"
/ {
model = "IGEPv2 (TI OMAP AM/DM37x)";
@@ -248,7 +248,7 @@ partition@780000 {
ethernet@gpmc {
pinctrl-names = "default";
- pinctrl-0 = <&smsc911x_pins>;
+ pinctrl-0 = <&smsc9221_pins>;
reg = <5 0 0xff>;
interrupt-parent = <&gpio6>;
interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm/boot/dts/omap3-sb-t35.dtsi b/arch/arm/boot/dts/omap3-sb-t35.dtsi
index 7909c51b05a5643563b4ed74405066e1a222a995..d59e3de1441e2f7dc5e0fb9b4bc29f49ee04cbc1 100644
--- a/arch/arm/boot/dts/omap3-sb-t35.dtsi
+++ b/arch/arm/boot/dts/omap3-sb-t35.dtsi
@@ -2,20 +2,6 @@
* Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730
*/
-/ {
- vddvario_sb_t35: regulator-vddvario-sb-t35 {
- compatible = "regulator-fixed";
- regulator-name = "vddvario";
- regulator-always-on;
- };
-
- vdd33a_sb_t35: regulator-vdd33a-sb-t35 {
- compatible = "regulator-fixed";
- regulator-name = "vdd33a";
- regulator-always-on;
- };
-};
-
&omap3_pmx_core {
smsc2_pins: pinmux_smsc2_pins {
pinctrl-single,pins = <
@@ -37,11 +23,10 @@ smsc2: ethernet@4,0 {
reg = <4 0 0xff>;
bank-width = <2>;
gpmc,mux-add-data;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <186>;
- gpmc,cs-wr-off-ns = <186>;
- gpmc,adv-on-ns = <12>;
- gpmc,adv-rd-off-ns = <48>;
+ gpmc,cs-on-ns = <1>;
+ gpmc,cs-rd-off-ns = <180>;
+ gpmc,cs-wr-off-ns = <180>;
+ gpmc,adv-rd-off-ns = <18>;
gpmc,adv-wr-off-ns = <48>;
gpmc,oe-on-ns = <54>;
gpmc,oe-off-ns = <168>;
@@ -49,16 +34,14 @@ smsc2: ethernet@4,0 {
gpmc,we-off-ns = <168>;
gpmc,rd-cycle-ns = <186>;
gpmc,wr-cycle-ns = <186>;
- gpmc,access-ns = <114>;
- gpmc,page-burst-access-ns = <6>;
- gpmc,bus-turnaround-ns = <12>;
- gpmc,cycle2cycle-delay-ns = <18>;
- gpmc,wr-data-mux-bus-ns = <90>;
- gpmc,wr-access-ns = <186>;
+ gpmc,access-ns = <144>;
+ gpmc,page-burst-access-ns = <24>;
+ gpmc,bus-turnaround-ns = <90>;
+ gpmc,cycle2cycle-delay-ns = <90>;
gpmc,cycle2cycle-samecsen;
gpmc,cycle2cycle-diffcsen;
- vddvario-supply = <&vddvario_sb_t35>;
- vdd33a-supply = <&vdd33a_sb_t35>;
+ vddvario-supply = <&vddvario>;
+ vdd33a-supply = <&vdd33a>;
reg-io-width = <4>;
smsc,save-mac-address;
};
diff --git a/arch/arm/boot/dts/omap3-sbc-t3517.dts b/arch/arm/boot/dts/omap3-sbc-t3517.dts
index 024c9c6c682d7eb4b421a559c7c4b5f95e0511f9..42189b65d393d29d2cf467ddbc5df4eb0661a471 100644
--- a/arch/arm/boot/dts/omap3-sbc-t3517.dts
+++ b/arch/arm/boot/dts/omap3-sbc-t3517.dts
@@ -8,6 +8,19 @@
/ {
model = "CompuLab SBC-T3517 with CM-T3517";
compatible = "compulab,omap3-sbc-t3517", "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
+
+ /* Only one GPMC smsc9220 on SBC-T3517, CM-T3517 uses am35x Ethernet */
+ vddvario: regulator-vddvario-sb-t35 {
+ compatible = "regulator-fixed";
+ regulator-name = "vddvario";
+ regulator-always-on;
+ };
+
+ vdd33a: regulator-vdd33a-sb-t35 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd33a";
+ regulator-always-on;
+ };
};
&omap3_pmx_core {
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index acb9019dc437b66321ec7995dc16456678a2e42c..4231191ade06acf8c7a02938a0fcfcbdeb318fbc 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -61,7 +61,7 @@ mpu {
ti,hwmods = "mpu";
};
- iva {
+ iva: iva {
compatible = "ti,iva2.2";
ti,hwmods = "iva";
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index f8c9855ce587c15790f79a2f04e0ff02933f463f..36b4312a5e0d82fb20fb6a7eb9b1d59942b0ec18 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -630,6 +630,13 @@ mcbsp3: mcbsp@40126000 {
status = "disabled";
};
+ mailbox: mailbox@4a0f4000 {
+ compatible = "ti,omap4-mailbox";
+ reg = <0x4a0f4000 0x200>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mailbox";
+ };
+
timer1: timer@4ae18000 {
compatible = "ti,omap5430-timer";
reg = <0x4ae18000 0x80>;
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index eabcfdbb403acc7ff40b409617a53c9831414c04..a106b0872910da874f1000f417a1aab1793237de 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -13,7 +13,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
/ {
model = "Atmel SAMA5D3 family SoC";
diff --git a/arch/arm/boot/dts/sama5d3_mci2.dtsi b/arch/arm/boot/dts/sama5d3_mci2.dtsi
index b029fe7ef17a657946de4d2fe71168b4b03210d8..1b02208ea6ff2b70aab43ddd416b37ef0b9a2a1f 100644
--- a/arch/arm/boot/dts/sama5d3_mci2.dtsi
+++ b/arch/arm/boot/dts/sama5d3_mci2.dtsi
@@ -9,7 +9,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
/ {
ahb {
diff --git a/arch/arm/boot/dts/sama5d3_tcb1.dtsi b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
index 382b04431f66b621e01a9f2fe7a9e488ac4c171b..02848453ca0cf5447de27aaca6b233611173da4e 100644
--- a/arch/arm/boot/dts/sama5d3_tcb1.dtsi
+++ b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
@@ -9,7 +9,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
/ {
aliases {
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi
index a9fa75e4165205f9a1259f9a0821519faee54070..7a8d4c6115f72fdab533980a0f0d96eb6cb1469a 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/sama5d3_uart.dtsi
@@ -9,7 +9,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
/ {
aliases {
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
index 32efc105df834de3c3143938bf0cfdebbf5d1b55..aba1c8a3f3883320a50b31dcac05341568e0a335 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/sun7i-a20.dtsi
@@ -87,7 +87,7 @@ pll1: clk@01c20000 {
pll4: clk@01c20018 {
#clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll1-clk";
+ compatible = "allwinner,sun7i-a20-pll4-clk";
reg = <0x01c20018 0x4>;
clocks = <&osc24M>;
clock-output-names = "pll4";
@@ -109,6 +109,14 @@ pll6: clk@01c20028 {
clock-output-names = "pll6_sata", "pll6_other", "pll6";
};
+ pll8: clk@01c20040 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun7i-a20-pll4-clk";
+ reg = <0x01c20040 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll8";
+ };
+
cpu: cpu@01c20054 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-cpu-clk";
@@ -805,9 +813,9 @@ i2c3: i2c@01c2b800 {
status = "disabled";
};
- i2c4: i2c@01c2bc00 {
+ i2c4: i2c@01c2c000 {
compatible = "allwinner,sun4i-i2c";
- reg = <0x01c2bc00 0x400>;
+ reg = <0x01c2c000 0x400>;
interrupts = <0 89 4>;
clocks = <&apb1_gates 15>;
clock-frequency = <100000>;
diff --git a/arch/arm/common/edma.c b/arch/arm/common/edma.c
index 41bca32409fce81358c3b5c35bc081bcc28e7c76..5339009b3c0ce648df92244b5d9274e78273290b 100644
--- a/arch/arm/common/edma.c
+++ b/arch/arm/common/edma.c
@@ -1423,55 +1423,38 @@ EXPORT_SYMBOL(edma_clear_event);
#if IS_ENABLED(CONFIG_OF) && IS_ENABLED(CONFIG_DMADEVICES)
-static int edma_of_read_u32_to_s16_array(const struct device_node *np,
- const char *propname, s16 *out_values,
- size_t sz)
+static int edma_xbar_event_map(struct device *dev, struct device_node *node,
+ struct edma_soc_info *pdata, size_t sz)
{
- int ret;
-
- ret = of_property_read_u16_array(np, propname, out_values, sz);
- if (ret)
- return ret;
-
- /* Terminate it */
- *out_values++ = -1;
- *out_values++ = -1;
-
- return 0;
-}
-
-static int edma_xbar_event_map(struct device *dev,
- struct device_node *node,
- struct edma_soc_info *pdata, int len)
-{
- int ret, i;
+ const char pname[] = "ti,edma-xbar-event-map";
struct resource res;
void __iomem *xbar;
- const s16 (*xbar_chans)[2];
+ s16 (*xbar_chans)[2];
+ size_t nelm = sz / sizeof(s16);
u32 shift, offset, mux;
+ int ret, i;
- xbar_chans = devm_kzalloc(dev,
- len/sizeof(s16) + 2*sizeof(s16),
- GFP_KERNEL);
+ xbar_chans = devm_kzalloc(dev, (nelm + 2) * sizeof(s16), GFP_KERNEL);
if (!xbar_chans)
return -ENOMEM;
ret = of_address_to_resource(node, 1, &res);
if (ret)
- return -EIO;
+ return -ENOMEM;
xbar = devm_ioremap(dev, res.start, resource_size(&res));
if (!xbar)
return -ENOMEM;
- ret = edma_of_read_u32_to_s16_array(node,
- "ti,edma-xbar-event-map",
- (s16 *)xbar_chans,
- len/sizeof(u32));
+ ret = of_property_read_u16_array(node, pname, (u16 *)xbar_chans, nelm);
if (ret)
return -EIO;
- for (i = 0; xbar_chans[i][0] != -1; i++) {
+ /* Invalidate last entry for the other user of this mess */
+ nelm >>= 1;
+ xbar_chans[nelm][0] = xbar_chans[nelm][1] = -1;
+
+ for (i = 0; i < nelm; i++) {
shift = (xbar_chans[i][1] & 0x03) << 3;
offset = xbar_chans[i][1] & 0xfffffffc;
mux = readl(xbar + offset);
@@ -1480,8 +1463,7 @@ static int edma_xbar_event_map(struct device *dev,
writel(mux, (xbar + offset));
}
- pdata->xbar_chans = xbar_chans;
-
+ pdata->xbar_chans = (const s16 (*)[2]) xbar_chans;
return 0;
}
diff --git a/arch/arm/configs/sunxi_defconfig b/arch/arm/configs/sunxi_defconfig
index b5df4a511b0acdfea6df30b7dd4b9753d2b00f9a..81ba78eaf54adb02840dbc2d41cc4af8acc7c08a 100644
--- a/arch/arm/configs/sunxi_defconfig
+++ b/arch/arm/configs/sunxi_defconfig
@@ -37,7 +37,7 @@ CONFIG_SUN4I_EMAC=y
# CONFIG_NET_VENDOR_NATSEMI is not set
# CONFIG_NET_VENDOR_SEEQ is not set
# CONFIG_NET_VENDOR_SMSC is not set
-# CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_STMMAC_ETH=y
# CONFIG_NET_VENDOR_WIZNET is not set
# CONFIG_WLAN is not set
CONFIG_SERIAL_8250=y
diff --git a/arch/arm/mach-omap2/omap-headsmp.S b/arch/arm/mach-omap2/omap-headsmp.S
index 75e92952c18efe3e597791e6798c2ee2ce5969a1..40c5d5f1451cd34b19ebed5e2d58f150f6f4a29d 100644
--- a/arch/arm/mach-omap2/omap-headsmp.S
+++ b/arch/arm/mach-omap2/omap-headsmp.S
@@ -1,7 +1,7 @@
/*
* Secondary CPU startup routine source file.
*
- * Copyright (C) 2009 Texas Instruments, Inc.
+ * Copyright (C) 2009-2014 Texas Instruments, Inc.
*
* Author:
* Santosh Shilimkar <santosh.shilimkar@ti.com>
@@ -28,9 +28,13 @@
* code. This routine also provides a holding flag into which
* secondary core is held until we're ready for it to initialise.
* The primary core will update this flag using a hardware
-+ * register AuxCoreBoot0.
+ * register AuxCoreBoot0.
*/
ENTRY(omap5_secondary_startup)
+.arm
+THUMB( adr r9, BSYM(wait) ) @ CPU may be entered in ARM mode.
+THUMB( bx r9 ) @ If this is a Thumb-2 kernel,
+THUMB( .thumb ) @ switch to Thumb now.
wait: ldr r2, =AUX_CORE_BOOT0_PA @ read from AuxCoreBoot0
ldr r0, [r2]
mov r0, r0, lsr #5
diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h
index f565f9944af2ee45b795b180391853ffa8810a12..7548db2bfb8a7e595d7672c5cfbba3868651d689 100644
--- a/arch/arm/mach-orion5x/common.h
+++ b/arch/arm/mach-orion5x/common.h
@@ -21,7 +21,7 @@ struct mv_sata_platform_data;
#define ORION_MBUS_DEVBUS_BOOT_ATTR 0x0f
#define ORION_MBUS_DEVBUS_TARGET(cs) 0x01
#define ORION_MBUS_DEVBUS_ATTR(cs) (~(1 << cs))
-#define ORION_MBUS_SRAM_TARGET 0x00
+#define ORION_MBUS_SRAM_TARGET 0x09
#define ORION_MBUS_SRAM_ATTR 0x00
/*
diff --git a/drivers/bus/mvebu-mbus.c b/drivers/bus/mvebu-mbus.c
index 293e2e0a0a87c7d9877c27524fd98503ba16c1cf..00b73448b22ea7b77a55785cfbbddf022bf4bfd3 100644
--- a/drivers/bus/mvebu-mbus.c
+++ b/drivers/bus/mvebu-mbus.c
@@ -56,6 +56,7 @@
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/debugfs.h>
+#include <linux/log2.h>
/*
* DDR target is the same on all platforms.
@@ -222,12 +223,6 @@ static int mvebu_mbus_window_conflicts(struct mvebu_mbus_state *mbus,
*/
if ((u64)base < wend && end > wbase)
return 0;
-
- /*
- * Check if target/attribute conflicts
- */
- if (target == wtarget && attr == wattr)
- return 0;
}
return 1;
@@ -266,6 +261,17 @@ static int mvebu_mbus_setup_window(struct mvebu_mbus_state *mbus,
mbus->soc->win_cfg_offset(win);
u32 ctrl, remap_addr;
+ if (!is_power_of_2(size)) {
+ WARN(true, "Invalid MBus window size: 0x%zx\n", size);
+ return -EINVAL;
+ }
+
+ if ((base & (phys_addr_t)(size - 1)) != 0) {
+ WARN(true, "Invalid MBus base/size: %pa len 0x%zx\n", &base,
+ size);
+ return -EINVAL;
+ }
+
ctrl = ((size - 1) & WIN_CTRL_SIZE_MASK) |
(attr << WIN_CTRL_ATTR_SHIFT) |
(target << WIN_CTRL_TGT_SHIFT) |
@@ -413,6 +419,10 @@ static int mvebu_devs_debug_show(struct seq_file *seq, void *v)
win, (unsigned long long)wbase,
(unsigned long long)(wbase + wsize), wtarget, wattr);
+ if (!is_power_of_2(wsize) ||
+ ((wbase & (u64)(wsize - 1)) != 0))
+ seq_puts(seq, " (Invalid base/size!!)");
+
if (win < mbus->soc->num_remappable_wins) {
seq_printf(seq, " (remap %016llx)\n",
(unsigned long long)wremap);
diff --git a/drivers/memory/mvebu-devbus.c b/drivers/memory/mvebu-devbus.c
index 110c03627051cb749ef92d853e47322714b1dd51..b59a17fb7c3e3f3eff43faecac3610f58df1dbd8 100644
--- a/drivers/memory/mvebu-devbus.c
+++ b/drivers/memory/mvebu-devbus.c
@@ -108,8 +108,19 @@ static int devbus_set_timing_params(struct devbus *devbus,
node->full_name);
return err;
}
- /* Convert bit width to byte width */
- r.bus_width /= 8;
+
+ /*
+ * The bus width is encoded into the register as 0 for 8 bits,
+ * and 1 for 16 bits, so we do the necessary conversion here.
+ */
+ if (r.bus_width == 8)
+ r.bus_width = 0;
+ else if (r.bus_width == 16)
+ r.bus_width = 1;
+ else {
+ dev_err(devbus->dev, "invalid bus width %d\n", r.bus_width);
+ return -EINVAL;
+ }
err = get_timing_param_ps(devbus, node, "devbus,badr-skew-ps",
&r.badr_skew);
diff --git a/drivers/pci/host/pci-mvebu.c b/drivers/pci/host/pci-mvebu.c
index d3d1cfd51e095f058404d96f063df76d227bd652..e384e2534594731a95eb7524fb75583fce208541 100644
--- a/drivers/pci/host/pci-mvebu.c
+++ b/drivers/pci/host/pci-mvebu.c
@@ -293,6 +293,58 @@ static int mvebu_pcie_hw_wr_conf(struct mvebu_pcie_port *port,
return PCIBIOS_SUCCESSFUL;
}
+/*
+ * Remove windows, starting from the largest ones to the smallest
+ * ones.
+ */
+static void mvebu_pcie_del_windows(struct mvebu_pcie_port *port,
+ phys_addr_t base, size_t size)
+{
+ while (size) {
+ size_t sz = 1 << (fls(size) - 1);
+
+ mvebu_mbus_del_window(base, sz);
+ base += sz;
+ size -= sz;
+ }
+}
+
+/*
+ * MBus windows can only have a power of two size, but PCI BARs do not
+ * have this constraint. Therefore, we have to split the PCI BAR into
+ * areas each having a power of two size. We start from the largest
+ * one (i.e highest order bit set in the size).
+ */
+static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port,
+ unsigned int target, unsigned int attribute,
+ phys_addr_t base, size_t size,
+ phys_addr_t remap)
+{
+ size_t size_mapped = 0;
+
+ while (size) {
+ size_t sz = 1 << (fls(size) - 1);
+ int ret;
+
+ ret = mvebu_mbus_add_window_remap_by_id(target, attribute, base,
+ sz, remap);
+ if (ret) {
+ dev_err(&port->pcie->pdev->dev,
+ "Could not create MBus window at 0x%x, size 0x%x: %d\n",
+ base, sz, ret);
+ mvebu_pcie_del_windows(port, base - size_mapped,
+ size_mapped);
+ return;
+ }
+
+ size -= sz;
+ size_mapped += sz;
+ base += sz;
+ if (remap != MVEBU_MBUS_NO_REMAP)
+ remap += sz;
+ }
+}
+
static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
{
phys_addr_t iobase;
@@ -304,8 +356,8 @@ static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
/* If a window was configured, remove it */
if (port->iowin_base) {
- mvebu_mbus_del_window(port->iowin_base,
- port->iowin_size);
+ mvebu_pcie_del_windows(port, port->iowin_base,
+ port->iowin_size);
port->iowin_base = 0;
port->iowin_size = 0;
}
@@ -331,11 +383,11 @@ static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
port->iowin_base = port->pcie->io.start + iobase;
port->iowin_size = ((0xFFF | ((port->bridge.iolimit & 0xF0) << 8) |
(port->bridge.iolimitupper << 16)) -
- iobase);
+ iobase) + 1;
- mvebu_mbus_add_window_remap_by_id(port->io_target, port->io_attr,
- port->iowin_base, port->iowin_size,
- iobase);
+ mvebu_pcie_add_windows(port, port->io_target, port->io_attr,
+ port->iowin_base, port->iowin_size,
+ iobase);
}
static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
@@ -346,8 +398,8 @@ static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
/* If a window was configured, remove it */
if (port->memwin_base) {
- mvebu_mbus_del_window(port->memwin_base,
- port->memwin_size);
+ mvebu_pcie_del_windows(port, port->memwin_base,
+ port->memwin_size);
port->memwin_base = 0;
port->memwin_size = 0;
}
@@ -364,10 +416,11 @@ static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
port->memwin_base = ((port->bridge.membase & 0xFFF0) << 16);
port->memwin_size =
(((port->bridge.memlimit & 0xFFF0) << 16) | 0xFFFFF) -
- port->memwin_base;
+ port->memwin_base + 1;
- mvebu_mbus_add_window_by_id(port->mem_target, port->mem_attr,
- port->memwin_base, port->memwin_size);
+ mvebu_pcie_add_windows(port, port->mem_target, port->mem_attr,
+ port->memwin_base, port->memwin_size,
+ MVEBU_MBUS_NO_REMAP);
}
/*
@@ -743,14 +796,21 @@ static resource_size_t mvebu_pcie_align_resource(struct pci_dev *dev,
/*
* On the PCI-to-PCI bridge side, the I/O windows must have at
- * least a 64 KB size and be aligned on their size, and the
- * memory windows must have at least a 1 MB size and be
- * aligned on their size
+ * least a 64 KB size and the memory windows must have at
+ * least a 1 MB size. Moreover, MBus windows need to have a
+ * base address aligned on their size, and their size must be
+ * a power of two. This means that if the BAR doesn't have a
+ * power of two size, several MBus windows will actually be
+ * created. We need to ensure that the biggest MBus window
+ * (which will be the first one) is aligned on its size, which
+ * explains the rounddown_pow_of_two() being done here.
*/
if (res->flags & IORESOURCE_IO)
- return round_up(start, max_t(resource_size_t, SZ_64K, size));
+ return round_up(start, max_t(resource_size_t, SZ_64K,
+ rounddown_pow_of_two(size)));
else if (res->flags & IORESOURCE_MEM)
- return round_up(start, max_t(resource_size_t, SZ_1M, size));
+ return round_up(start, max_t(resource_size_t, SZ_1M,
+ rounddown_pow_of_two(size)));
else
return start;
}
diff --git a/include/dt-bindings/clk/at91.h b/include/dt-bindings/clock/at91.h
similarity index 100%
rename from include/dt-bindings/clk/at91.h
rename to include/dt-bindings/clock/at91.h