diff --git a/Documentation/devicetree/bindings/arm/tegra/emc.txt b/Documentation/devicetree/bindings/arm/tegra/emc.txt
new file mode 100644
index 0000000000000000000000000000000000000000..09335f8eee0068c091546fb82d66b506c61701b5
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/emc.txt
@@ -0,0 +1,100 @@
+Embedded Memory Controller
+
+Properties:
+- name : Should be emc
+- #address-cells : Should be 1
+- #size-cells : Should be 0
+- compatible : Should contain "nvidia,tegra20-emc".
+- reg : Offset and length of the register set for the device
+- nvidia,use-ram-code : If present, the sub-nodes will be addressed
+ and chosen using the ramcode board selector. If omitted, only one
+ set of tables can be present and said tables will be used
+ irrespective of ram-code configuration.
+
+Child device nodes describe the memory settings for different configurations and clock rates.
+
+Example:
+
+ emc@7000f400 {
+ #address-cells = < 1 >;
+ #size-cells = < 0 >;
+ compatible = "nvidia,tegra20-emc";
+ reg = <0x7000f4000 0x200>;
+ }
+
+
+Embedded Memory Controller ram-code table
+
+If the emc node has the nvidia,use-ram-code property present, then the
+next level of nodes below the emc table are used to specify which settings
+apply for which ram-code settings.
+
+If the emc node lacks the nvidia,use-ram-code property, this level is omitted
+and the tables are stored directly under the emc node (see below).
+
+Properties:
+
+- name : Should be emc-tables
+- nvidia,ram-code : the binary representation of the ram-code board strappings
+ for which this node (and children) are valid.
+
+
+
+Embedded Memory Controller configuration table
+
+This is a table containing the EMC register settings for the various
+operating speeds of the memory controller. They are always located as
+subnodes of the emc controller node.
+
+There are two ways of specifying which tables to use:
+
+* The simplest is if there is just one set of tables in the device tree,
+ and they will always be used (based on which frequency is used).
+ This is the preferred method, especially when firmware can fill in
+ this information based on the specific system information and just
+ pass it on to the kernel.
+
+* The slightly more complex one is when more than one memory configuration
+ might exist on the system. The Tegra20 platform handles this during
+ early boot by selecting one out of possible 4 memory settings based
+ on a 2-pin "ram code" bootstrap setting on the board. The values of
+ these strappings can be read through a register in the SoC, and thus
+ used to select which tables to use.
+
+Properties:
+- name : Should be emc-table
+- compatible : Should contain "nvidia,tegra20-emc-table".
+- reg : either an opaque enumerator to tell different tables apart, or
+ the valid frequency for which the table should be used (in kHz).
+- clock-frequency : the clock frequency for the EMC at which this
+ table should be used (in kHz).
+- nvidia,emc-registers : a 46 word array of EMC registers to be programmed
+ for operation at the 'clock-frequency' setting.
+ The order and contents of the registers are:
+ RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT,
+ WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR,
+ PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW,
+ TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE,
+ ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE,
+ ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0,
+ CFG_CLKTRIM_1, CFG_CLKTRIM_2
+
+ emc-table@166000 {
+ reg = <166000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 166000 >;
+ nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 >;
+ };
+
+ emc-table@333000 {
+ reg = <333000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 333000 >;
+ nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 >;
+ };
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
new file mode 100644
index 0000000000000000000000000000000000000000..b5846e21cc2e53306fdba8304bf9cf12a6595126
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
@@ -0,0 +1,19 @@
+NVIDIA Tegra Power Management Controller (PMC)
+
+Properties:
+- name : Should be pmc
+- compatible : Should contain "nvidia,tegra<chip>-pmc".
+- reg : Offset and length of the register set for the device
+- nvidia,invert-interrupt : If present, inverts the PMU interrupt signal.
+ The PMU is an external Power Management Unit, whose interrupt output
+ signal is fed into the PMC. This signal is optionally inverted, and then
+ fed into the ARM GIC. The PMC is not involved in the detection or
+ handling of this interrupt signal, merely its inversion.
+
+Example:
+
+pmc@7000f400 {
+ compatible = "nvidia,tegra20-pmc";
+ reg = <0x7000e400 0x400>;
+ nvidia,invert-interrupt;
+};
diff --git a/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt
new file mode 100644
index 0000000000000000000000000000000000000000..90fa7da525b8dd7ede457b5e44a00338f805d099
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt
@@ -0,0 +1,30 @@
+* NVIDIA Tegra APB DMA controller
+
+Required properties:
+- compatible: Should be "nvidia,<chip>-apbdma"
+- reg: Should contain DMA registers location and length. This shuld include
+ all of the per-channel registers.
+- interrupts: Should contain all of the per-channel DMA interrupts.
+
+Examples:
+
+apbdma: dma@6000a000 {
+ compatible = "nvidia,tegra20-apbdma";
+ reg = <0x6000a000 0x1200>;
+ interrupts = < 0 136 0x04
+ 0 137 0x04
+ 0 138 0x04
+ 0 139 0x04
+ 0 140 0x04
+ 0 141 0x04
+ 0 142 0x04
+ 0 143 0x04
+ 0 144 0x04
+ 0 145 0x04
+ 0 146 0x04
+ 0 147 0x04
+ 0 148 0x04
+ 0 149 0x04
+ 0 150 0x04
+ 0 151 0x04 >;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
index eb4b530d64e16d35481b013e5e6fb1c59aca15b9..023c9526e5f838c277eefdd10292943c11b4fd5a 100644
--- a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
@@ -1,8 +1,40 @@
-NVIDIA Tegra 2 GPIO controller
+NVIDIA Tegra GPIO controller
Required properties:
-- compatible : "nvidia,tegra20-gpio"
+- compatible : "nvidia,tegra<chip>-gpio"
+- reg : Physical base address and length of the controller's registers.
+- interrupts : The interrupt outputs from the controller. For Tegra20,
+ there should be 7 interrupts specified, and for Tegra30, there should
+ be 8 interrupts specified.
- #gpio-cells : Should be two. The first cell is the pin number and the
second cell is used to specify optional parameters:
- bit 0 specifies polarity (0 for normal, 1 for inverted)
- gpio-controller : Marks the device node as a GPIO controller.
+- #interrupt-cells : Should be 2.
+ The first cell is the GPIO number.
+ The second cell is used to specify flags:
+ bits[3:0] trigger type and level flags:
+ 1 = low-to-high edge triggered.
+ 2 = high-to-low edge triggered.
+ 4 = active high level-sensitive.
+ 8 = active low level-sensitive.
+ Valid combinations are 1, 2, 3, 4, 8.
+- interrupt-controller : Marks the device node as an interrupt controller.
+
+Example:
+
+gpio: gpio@6000d000 {
+ compatible = "nvidia,tegra20-gpio";
+ reg = < 0x6000d000 0x1000 >;
+ interrupts = < 0 32 0x04
+ 0 33 0x04
+ 0 34 0x04
+ 0 35 0x04
+ 0 55 0x04
+ 0 87 0x04
+ 0 89 0x04 >;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+};
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index c941fd06b2af323d6d7428ee3881ab541b257b34..8ef416a3a551c8315b9eb06ffdd7bbabd0d7a626 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -760,7 +760,7 @@ config ARCH_SA1100
select ARCH_HAS_CPUFREQ
select CPU_FREQ
select GENERIC_CLOCKEVENTS
- select HAVE_CLK
+ select CLKDEV_LOOKUP
select HAVE_SCHED_CLOCK
select TICK_ONESHOT
select ARCH_REQUIRE_GPIOLIB
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index b895a2a92da8186f5eda5aa04a5ee9ee51410cd1..66ca8014ff3e6648fcb353923e39ee4663d3edc4 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -180,12 +180,12 @@ choice
Say Y here if you want kernel low-level debugging support
on i.MX50 or i.MX53.
- config DEBUG_IMX6Q_UART
- bool "i.MX6Q Debug UART"
+ config DEBUG_IMX6Q_UART4
+ bool "i.MX6Q Debug UART4"
depends on SOC_IMX6Q
help
Say Y here if you want kernel low-level debugging support
- on i.MX6Q.
+ on i.MX6Q UART4.
config DEBUG_MSM_UART1
bool "Kernel low-level debugging messages via MSM UART1"
diff --git a/arch/arm/boot/dts/tegra-harmony.dts b/arch/arm/boot/dts/tegra-harmony.dts
index 80afa1b70b80d6ed448692a5434014fa36e910f8..6e8447dc020203c537383caa219d6c23bf2e775c 100644
--- a/arch/arm/boot/dts/tegra-harmony.dts
+++ b/arch/arm/boot/dts/tegra-harmony.dts
@@ -10,19 +10,25 @@ memory@0 {
reg = < 0x00000000 0x40000000 >;
};
+ pmc@7000f400 {
+ nvidia,invert-interrupt;
+ };
+
i2c@7000c000 {
clock-frequency = <400000>;
- codec: wm8903@1a {
+ wm8903: wm8903@1a {
compatible = "wlf,wm8903";
reg = <0x1a>;
- interrupts = < 347 >;
+ interrupt-parent = <&gpio>;
+ interrupts = < 187 0x04 >;
gpio-controller;
#gpio-cells = <2>;
- /* 0x8000 = Not configured */
- gpio-cfg = < 0x8000 0x8000 0 0x8000 0x8000 >;
+ micdet-cfg = <0>;
+ micdet-delay = <100>;
+ gpio-cfg = < 0xffffffff 0xffffffff 0 0xffffffff 0xffffffff >;
};
};
@@ -38,13 +44,32 @@ i2c@7000d000 {
clock-frequency = <400000>;
};
- sound {
- compatible = "nvidia,harmony-sound", "nvidia,tegra-wm8903";
+ i2s@70002a00 {
+ status = "disable";
+ };
- spkr-en-gpios = <&codec 2 0>;
- hp-det-gpios = <&gpio 178 0>;
- int-mic-en-gpios = <&gpio 184 0>;
- ext-mic-en-gpios = <&gpio 185 0>;
+ sound {
+ compatible = "nvidia,tegra-audio-wm8903-harmony",
+ "nvidia,tegra-audio-wm8903";
+ nvidia,model = "NVIDIA Tegra Harmony";
+
+ nvidia,audio-routing =
+ "Headphone Jack", "HPOUTR",
+ "Headphone Jack", "HPOUTL",
+ "Int Spk", "ROP",
+ "Int Spk", "RON",
+ "Int Spk", "LOP",
+ "Int Spk", "LON",
+ "Mic Jack", "MICBIAS",
+ "IN1L", "Mic Jack";
+
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&wm8903>;
+
+ nvidia,spkr-en-gpios = <&wm8903 2 0>;
+ nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+ nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
+ nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
};
serial@70006000 {
diff --git a/arch/arm/boot/dts/tegra-paz00.dts b/arch/arm/boot/dts/tegra-paz00.dts
index 61f385809970a27d455dfe49b33ffceb938980c0..fc97254c36449c499d13db86cc4dc8c5e021b4d8 100644
--- a/arch/arm/boot/dts/tegra-paz00.dts
+++ b/arch/arm/boot/dts/tegra-paz00.dts
@@ -12,6 +12,13 @@ memory@0 {
i2c@7000c000 {
clock-frequency = <400000>;
+
+ alc5632: alc5632@1e {
+ compatible = "realtek,alc5632";
+ reg = <0x1e>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
};
i2c@7000c400 {
@@ -42,6 +49,29 @@ adt7461@4c {
};
};
+ i2s@70002a00 {
+ status = "disable";
+ };
+
+ sound {
+ compatible = "nvidia,tegra-audio-alc5632-paz00",
+ "nvidia,tegra-audio-alc5632";
+
+ nvidia,model = "Compal PAZ00";
+
+ nvidia,audio-routing =
+ "Int Spk", "SPKOUT",
+ "Int Spk", "SPKOUTN",
+ "Headset Mic", "MICBIAS1",
+ "MIC1", "Headset Mic",
+ "Headset Stereophone", "HPR",
+ "Headset Stereophone", "HPL";
+
+ nvidia,audio-codec = <&alc5632>;
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+ };
+
serial@70006000 {
clock-frequency = <216000000>;
};
diff --git a/arch/arm/boot/dts/tegra-seaboard.dts b/arch/arm/boot/dts/tegra-seaboard.dts
index b55a02e34ba7fe13bacfbaf1e25f5aa515b984ac..876d5c92ce3692eb979918d5e9a08d85f73d5a57 100644
--- a/arch/arm/boot/dts/tegra-seaboard.dts
+++ b/arch/arm/boot/dts/tegra-seaboard.dts
@@ -13,6 +13,20 @@ memory {
i2c@7000c000 {
clock-frequency = <400000>;
+
+ wm8903: wm8903@1a {
+ compatible = "wlf,wm8903";
+ reg = <0x1a>;
+ interrupt-parent = <&gpio>;
+ interrupts = < 187 0x04 >;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ micdet-cfg = <0>;
+ micdet-delay = <100>;
+ gpio-cfg = < 0xffffffff 0xffffffff 0 0xffffffff 0xffffffff >;
+ };
};
i2c@7000c400 {
@@ -32,6 +46,32 @@ adt7461@4c {
};
};
+ i2s@70002a00 {
+ status = "disable";
+ };
+
+ sound {
+ compatible = "nvidia,tegra-audio-wm8903-seaboard",
+ "nvidia,tegra-audio-wm8903";
+ nvidia,model = "NVIDIA Tegra Seaboard";
+
+ nvidia,audio-routing =
+ "Headphone Jack", "HPOUTR",
+ "Headphone Jack", "HPOUTL",
+ "Int Spk", "ROP",
+ "Int Spk", "RON",
+ "Int Spk", "LOP",
+ "Int Spk", "LON",
+ "Mic Jack", "MICBIAS",
+ "IN1R", "Mic Jack";
+
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&wm8903>;
+
+ nvidia,spkr-en-gpios = <&wm8903 2 0>;
+ nvidia,hp-det-gpios = <&gpio 185 0>; /* gpio PX1 */
+ };
+
serial@70006000 {
status = "disable";
};
@@ -93,4 +133,42 @@ lid {
gpio-key,wakeup;
};
};
+
+ emc@7000f400 {
+ emc-table@190000 {
+ reg = < 190000 >;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 190000 >;
+ nvidia,emc-registers = < 0x0000000c 0x00000026
+ 0x00000009 0x00000003 0x00000004 0x00000004
+ 0x00000002 0x0000000c 0x00000003 0x00000003
+ 0x00000002 0x00000001 0x00000004 0x00000005
+ 0x00000004 0x00000009 0x0000000d 0x0000059f
+ 0x00000000 0x00000003 0x00000003 0x00000003
+ 0x00000003 0x00000001 0x0000000b 0x000000c8
+ 0x00000003 0x00000007 0x00000004 0x0000000f
+ 0x00000002 0x00000000 0x00000000 0x00000002
+ 0x00000000 0x00000000 0x00000083 0xa06204ae
+ 0x007dc010 0x00000000 0x00000000 0x00000000
+ 0x00000000 0x00000000 0x00000000 0x00000000 >;
+ };
+
+ emc-table@380000 {
+ reg = < 380000 >;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 380000 >;
+ nvidia,emc-registers = < 0x00000017 0x0000004b
+ 0x00000012 0x00000006 0x00000004 0x00000005
+ 0x00000003 0x0000000c 0x00000006 0x00000006
+ 0x00000003 0x00000001 0x00000004 0x00000005
+ 0x00000004 0x00000009 0x0000000d 0x00000b5f
+ 0x00000000 0x00000003 0x00000003 0x00000006
+ 0x00000006 0x00000001 0x00000011 0x000000c8
+ 0x00000003 0x0000000e 0x00000007 0x0000000f
+ 0x00000002 0x00000000 0x00000000 0x00000002
+ 0x00000000 0x00000000 0x00000083 0xe044048b
+ 0x007d8010 0x00000000 0x00000000 0x00000000
+ 0x00000000 0x00000000 0x00000000 0x00000000 >;
+ };
+ };
};
diff --git a/arch/arm/boot/dts/tegra-trimslice.dts b/arch/arm/boot/dts/tegra-trimslice.dts
index 3b3ee7db99f3f6893b9113915b016954aa6a3cb9..252476867b54a6804a0c63f484ed4766698c3787 100644
--- a/arch/arm/boot/dts/tegra-trimslice.dts
+++ b/arch/arm/boot/dts/tegra-trimslice.dts
@@ -26,6 +26,18 @@ i2c@7000d000 {
status = "disable";
};
+ i2s@70002800 {
+ status = "disable";
+ };
+
+ i2s@70002a00 {
+ status = "disable";
+ };
+
+ das@70000c00 {
+ status = "disable";
+ };
+
serial@70006000 {
clock-frequency = < 216000000 >;
};
diff --git a/arch/arm/boot/dts/tegra-ventana.dts b/arch/arm/boot/dts/tegra-ventana.dts
index c7d3b87f29dfe0458f047cf64e1dc4f23d5758f9..2dcff8728e904a03dc5ba1200b633617e2c9b048 100644
--- a/arch/arm/boot/dts/tegra-ventana.dts
+++ b/arch/arm/boot/dts/tegra-ventana.dts
@@ -12,6 +12,20 @@ memory {
i2c@7000c000 {
clock-frequency = <400000>;
+
+ wm8903: wm8903@1a {
+ compatible = "wlf,wm8903";
+ reg = <0x1a>;
+ interrupt-parent = <&gpio>;
+ interrupts = < 187 0x04 >;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ micdet-cfg = <0>;
+ micdet-delay = <100>;
+ gpio-cfg = < 0xffffffff 0xffffffff 0 0xffffffff 0xffffffff >;
+ };
};
i2c@7000c400 {
@@ -26,6 +40,34 @@ i2c@7000d000 {
clock-frequency = <400000>;
};
+ i2s@70002a00 {
+ status = "disable";
+ };
+
+ sound {
+ compatible = "nvidia,tegra-audio-wm8903-ventana",
+ "nvidia,tegra-audio-wm8903";
+ nvidia,model = "NVIDIA Tegra Ventana";
+
+ nvidia,audio-routing =
+ "Headphone Jack", "HPOUTR",
+ "Headphone Jack", "HPOUTL",
+ "Int Spk", "ROP",
+ "Int Spk", "RON",
+ "Int Spk", "LOP",
+ "Int Spk", "LON",
+ "Mic Jack", "MICBIAS",
+ "IN1L", "Mic Jack";
+
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&wm8903>;
+
+ nvidia,spkr-en-gpios = <&wm8903 2 0>;
+ nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+ nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
+ nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+ };
+
serial@70006000 {
status = "disable";
};
diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi
index 3da7afd45322ba288de7c36ac85923c53aed05a9..ec1f0101c79c928762d22b2339dc6c9d14c777af 100644
--- a/arch/arm/boot/dts/tegra20.dtsi
+++ b/arch/arm/boot/dts/tegra20.dtsi
@@ -4,6 +4,11 @@ / {
compatible = "nvidia,tegra20";
interrupt-parent = <&intc>;
+ pmc@7000f400 {
+ compatible = "nvidia,tegra20-pmc";
+ reg = <0x7000e400 0x400>;
+ };
+
intc: interrupt-controller@50041000 {
compatible = "arm,cortex-a9-gic";
interrupt-controller;
@@ -12,6 +17,27 @@ intc: interrupt-controller@50041000 {
< 0x50040100 0x0100 >;
};
+ apbdma: dma@6000a000 {
+ compatible = "nvidia,tegra20-apbdma";
+ reg = <0x6000a000 0x1200>;
+ interrupts = < 0 104 0x04
+ 0 105 0x04
+ 0 106 0x04
+ 0 107 0x04
+ 0 108 0x04
+ 0 109 0x04
+ 0 110 0x04
+ 0 111 0x04
+ 0 112 0x04
+ 0 113 0x04
+ 0 114 0x04
+ 0 115 0x04
+ 0 116 0x04
+ 0 117 0x04
+ 0 118 0x04
+ 0 119 0x04 >;
+ };
+
i2c@7000c000 {
#address-cells = <1>;
#size-cells = <0>;
@@ -44,18 +70,18 @@ i2c@7000d000 {
interrupts = < 0 53 0x04 >;
};
- i2s@70002800 {
+ tegra_i2s1: i2s@70002800 {
compatible = "nvidia,tegra20-i2s";
reg = <0x70002800 0x200>;
interrupts = < 0 13 0x04 >;
- dma-channel = < 2 >;
+ nvidia,dma-request-selector = < &apbdma 2 >;
};
- i2s@70002a00 {
+ tegra_i2s2: i2s@70002a00 {
compatible = "nvidia,tegra20-i2s";
reg = <0x70002a00 0x200>;
interrupts = < 0 3 0x04 >;
- dma-channel = < 1 >;
+ nvidia,dma-request-selector = < &apbdma 1 >;
};
das@70000c00 {
@@ -75,6 +101,8 @@ gpio: gpio@6000d000 {
0 89 0x04 >;
#gpio-cells = <2>;
gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
};
pinmux: pinmux@70000000 {
@@ -120,6 +148,13 @@ serial@70006400 {
interrupts = < 0 91 0x04 >;
};
+ emc@7000f400 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "nvidia,tegra20-emc";
+ reg = <0x7000f400 0x200>;
+ };
+
sdhci@c8000000 {
compatible = "nvidia,tegra20-sdhci";
reg = <0xc8000000 0x200>;
diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi
index ee7db9892e02aba2786613b3e7c52541659adcae..ac4b75cb26c060b3d5a7f605bc7f5566266cf161 100644
--- a/arch/arm/boot/dts/tegra30.dtsi
+++ b/arch/arm/boot/dts/tegra30.dtsi
@@ -4,6 +4,11 @@ / {
compatible = "nvidia,tegra30";
interrupt-parent = <&intc>;
+ pmc@7000f400 {
+ compatible = "nvidia,tegra20-pmc", "nvidia,tegra30-pmc";
+ reg = <0x7000e400 0x400>;
+ };
+
intc: interrupt-controller@50041000 {
compatible = "arm,cortex-a9-gic";
interrupt-controller;
@@ -12,6 +17,43 @@ intc: interrupt-controller@50041000 {
< 0x50040100 0x0100 >;
};
+ apbdma: dma@6000a000 {
+ compatible = "nvidia,tegra30-apbdma", "nvidia,tegra20-apbdma";
+ reg = <0x6000a000 0x1400>;
+ interrupts = < 0 104 0x04
+ 0 105 0x04
+ 0 106 0x04
+ 0 107 0x04
+ 0 108 0x04
+ 0 109 0x04
+ 0 110 0x04
+ 0 111 0x04
+ 0 112 0x04
+ 0 113 0x04
+ 0 114 0x04
+ 0 115 0x04
+ 0 116 0x04
+ 0 117 0x04
+ 0 118 0x04
+ 0 119 0x04
+ 0 128 0x04
+ 0 129 0x04
+ 0 130 0x04
+ 0 131 0x04
+ 0 132 0x04
+ 0 133 0x04
+ 0 134 0x04
+ 0 135 0x04
+ 0 136 0x04
+ 0 137 0x04
+ 0 138 0x04
+ 0 139 0x04
+ 0 140 0x04
+ 0 141 0x04
+ 0 142 0x04
+ 0 143 0x04 >;
+ };
+
i2c@7000c000 {
#address-cells = <1>;
#size-cells = <0>;
@@ -55,9 +97,18 @@ i2c@7000d000 {
gpio: gpio@6000d000 {
compatible = "nvidia,tegra30-gpio", "nvidia,tegra20-gpio";
reg = < 0x6000d000 0x1000 >;
- interrupts = < 0 32 0x04 0 33 0x04 0 34 0x04 0 35 0x04 0 55 0x04 0 87 0x04 0 89 0x04 >;
+ interrupts = < 0 32 0x04
+ 0 33 0x04
+ 0 34 0x04
+ 0 35 0x04
+ 0 55 0x04
+ 0 87 0x04
+ 0 89 0x04
+ 0 125 0x04 >;
#gpio-cells = <2>;
gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
};
serial@70006000 {
diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig
index d88fb87b414d721f9359252798efdd680070e1d7..b5ac644e12af9121985b0eadeecfdefaaf85c33b 100644
--- a/arch/arm/configs/imx_v4_v5_defconfig
+++ b/arch/arm/configs/imx_v4_v5_defconfig
@@ -45,6 +45,7 @@ CONFIG_FPE_NWFPE=y
CONFIG_FPE_NWFPE_XP=y
CONFIG_PM_DEBUG=y
CONFIG_NET=y
+CONFIG_SMSC911X=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
@@ -79,6 +80,8 @@ CONFIG_MISC_DEVICES=y
CONFIG_EEPROM_AT24=y
CONFIG_EEPROM_AT25=y
CONFIG_NETDEVICES=y
+CONFIG_CS89x0=y
+CONFIG_CS89x0_PLATFORM=y
CONFIG_DM9000=y
CONFIG_SMC91X=y
CONFIG_SMC911X=y
@@ -116,6 +119,21 @@ CONFIG_FB_IMX=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_LCD_L4F00242T03=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_VIDEO_DEV=y
+CONFIG_VIDEO_V4L2_COMMON=y
+CONFIG_VIDEO_MEDIA=y
+CONFIG_VIDEO_V4L2=y
+CONFIG_VIDEOBUF_GEN=y
+CONFIG_VIDEOBUF_DMA_CONTIG=y
+CONFIG_VIDEOBUF2_CORE=y
+CONFIG_VIDEO_CAPTURE_DRIVERS=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_SOC_CAMERA=y
+CONFIG_SOC_CAMERA_OV2640=y
+CONFIG_VIDEO_MX2_HOSTSUPPORT=y
+CONFIG_VIDEO_MX2=y
CONFIG_BACKLIGHT_PWM=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FONTS=y
diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 3cd606905178a5c299331589435b3f5f08850f51..dc6f6411bbf5e9fb640831da44aa36f3d82cbb5c 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -81,6 +81,8 @@ CONFIG_PATA_IMX=y
CONFIG_NETDEVICES=y
# CONFIG_NET_VENDOR_BROADCOM is not set
# CONFIG_NET_VENDOR_CHELSIO is not set
+CONFIG_CS89x0=y
+CONFIG_CS89x0_PLATFORM=y
# CONFIG_NET_VENDOR_FARADAY is not set
# CONFIG_NET_VENDOR_INTEL is not set
# CONFIG_NET_VENDOR_MARVELL is not set
@@ -125,7 +127,39 @@ CONFIG_IMX2_WDT=y
CONFIG_MFD_MC13XXX=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_MC13783=y
CONFIG_REGULATOR_MC13892=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_VIDEO_V4L2=y
+CONFIG_VIDEO_DEV=y
+CONFIG_VIDEO_V4L2_COMMON=y
+CONFIG_VIDEOBUF_GEN=y
+CONFIG_VIDEOBUF2_CORE=y
+CONFIG_VIDEOBUF2_MEMOPS=y
+CONFIG_VIDEOBUF2_DMA_CONTIG=y
+CONFIG_VIDEO_CAPTURE_DRIVERS=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_SOC_CAMERA=y
+CONFIG_SOC_CAMERA_OV2640=y
+CONFIG_MX3_VIDEO=y
+CONFIG_VIDEO_MX3=y
+CONFIG_FB=y
+CONFIG_FB_MX3=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+CONFIG_LCD_L4F00242T03=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_GENERIC=y
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_MXC=y
diff --git a/arch/arm/configs/magician_defconfig b/arch/arm/configs/magician_defconfig
index 443675d317e6de326c576caf47ae9ff179a0814c..a691ef4c6008bac6a96c38aeb6615e685025d8ee 100644
--- a/arch/arm/configs/magician_defconfig
+++ b/arch/arm/configs/magician_defconfig
@@ -101,7 +101,7 @@ CONFIG_MFD_ASIC3=y
CONFIG_HTC_EGPIO=y
CONFIG_HTC_PASIC3=y
CONFIG_REGULATOR=y
-CONFIG_REGULATOR_BQ24022=y
+CONFIG_REGULATOR_GPIO=y
CONFIG_FB=y
CONFIG_FB_PXA=y
CONFIG_FB_PXA_OVERLAY=y
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index 366a7765635b380538c103e3c0027519550521d0..70709ab0102ad74f3f44354051b0d19ca4784598 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -891,7 +891,8 @@ static struct platform_device at91sam9263_isi_device = {
.num_resources = ARRAY_SIZE(isi_resources),
};
-void __init at91_add_device_isi(void)
+void __init at91_add_device_isi(struct isi_platform_data *data,
+ bool use_pck_as_mck)
{
at91_set_A_periph(AT91_PIN_PE0, 0); /* ISI_D0 */
at91_set_A_periph(AT91_PIN_PE1, 0); /* ISI_D1 */
@@ -904,14 +905,20 @@ void __init at91_add_device_isi(void)
at91_set_A_periph(AT91_PIN_PE8, 0); /* ISI_PCK */
at91_set_A_periph(AT91_PIN_PE9, 0); /* ISI_HSYNC */
at91_set_A_periph(AT91_PIN_PE10, 0); /* ISI_VSYNC */
- at91_set_B_periph(AT91_PIN_PE11, 0); /* ISI_MCK (PCK3) */
at91_set_B_periph(AT91_PIN_PE12, 0); /* ISI_PD8 */
at91_set_B_periph(AT91_PIN_PE13, 0); /* ISI_PD9 */
at91_set_B_periph(AT91_PIN_PE14, 0); /* ISI_PD10 */
at91_set_B_periph(AT91_PIN_PE15, 0); /* ISI_PD11 */
+
+ if (use_pck_as_mck) {
+ at91_set_B_periph(AT91_PIN_PE11, 0); /* ISI_MCK (PCK3) */
+
+ /* TODO: register the PCK for ISI_MCK and set its parent */
+ }
}
#else
-void __init at91_add_device_isi(void) {}
+void __init at91_add_device_isi(struct isi_platform_data *data,
+ bool use_pck_as_mck) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index 96e2adcd5a841907be15beda7bdbb67dd87b5259..bd4e68cd3e2f31d43c982a03f405c544cabb926a 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -14,6 +14,7 @@
#include <linux/dma-mapping.h>
#include <linux/gpio.h>
+#include <linux/clk.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <linux/atmel-mci.h>
@@ -28,7 +29,10 @@
#include <mach/at_hdmac.h>
#include <mach/atmel-mci.h>
+#include <media/atmel-isi.h>
+
#include "generic.h"
+#include "clock.h"
/* --------------------------------------------------------------------
@@ -870,6 +874,96 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
#endif
+/* --------------------------------------------------------------------
+ * Image Sensor Interface
+ * -------------------------------------------------------------------- */
+#if defined(CONFIG_VIDEO_ATMEL_ISI) || defined(CONFIG_VIDEO_ATMEL_ISI_MODULE)
+static u64 isi_dmamask = DMA_BIT_MASK(32);
+static struct isi_platform_data isi_data;
+
+struct resource isi_resources[] = {
+ [0] = {
+ .start = AT91SAM9G45_BASE_ISI,
+ .end = AT91SAM9G45_BASE_ISI + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9G45_ID_ISI,
+ .end = AT91SAM9G45_ID_ISI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9g45_isi_device = {
+ .name = "atmel_isi",
+ .id = 0,
+ .dev = {
+ .dma_mask = &isi_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &isi_data,
+ },
+ .resource = isi_resources,
+ .num_resources = ARRAY_SIZE(isi_resources),
+};
+
+static struct clk_lookup isi_mck_lookups[] = {
+ CLKDEV_CON_DEV_ID("isi_mck", "atmel_isi.0", NULL),
+};
+
+void __init at91_add_device_isi(struct isi_platform_data *data,
+ bool use_pck_as_mck)
+{
+ struct clk *pck;
+ struct clk *parent;
+
+ if (!data)
+ return;
+ isi_data = *data;
+
+ at91_set_A_periph(AT91_PIN_PB20, 0); /* ISI_D0 */
+ at91_set_A_periph(AT91_PIN_PB21, 0); /* ISI_D1 */
+ at91_set_A_periph(AT91_PIN_PB22, 0); /* ISI_D2 */
+ at91_set_A_periph(AT91_PIN_PB23, 0); /* ISI_D3 */
+ at91_set_A_periph(AT91_PIN_PB24, 0); /* ISI_D4 */
+ at91_set_A_periph(AT91_PIN_PB25, 0); /* ISI_D5 */
+ at91_set_A_periph(AT91_PIN_PB26, 0); /* ISI_D6 */
+ at91_set_A_periph(AT91_PIN_PB27, 0); /* ISI_D7 */
+ at91_set_A_periph(AT91_PIN_PB28, 0); /* ISI_PCK */
+ at91_set_A_periph(AT91_PIN_PB30, 0); /* ISI_HSYNC */
+ at91_set_A_periph(AT91_PIN_PB29, 0); /* ISI_VSYNC */
+ at91_set_B_periph(AT91_PIN_PB8, 0); /* ISI_PD8 */
+ at91_set_B_periph(AT91_PIN_PB9, 0); /* ISI_PD9 */
+ at91_set_B_periph(AT91_PIN_PB10, 0); /* ISI_PD10 */
+ at91_set_B_periph(AT91_PIN_PB11, 0); /* ISI_PD11 */
+
+ platform_device_register(&at91sam9g45_isi_device);
+
+ if (use_pck_as_mck) {
+ at91_set_B_periph(AT91_PIN_PB31, 0); /* ISI_MCK (PCK1) */
+
+ pck = clk_get(NULL, "pck1");
+ parent = clk_get(NULL, "plla");
+
+ BUG_ON(IS_ERR(pck) || IS_ERR(parent));
+
+ if (clk_set_parent(pck, parent)) {
+ pr_err("Failed to set PCK's parent\n");
+ } else {
+ /* Register PCK as ISI_MCK */
+ isi_mck_lookups[0].clk = pck;
+ clkdev_add_table(isi_mck_lookups,
+ ARRAY_SIZE(isi_mck_lookups));
+ }
+
+ clk_put(pck);
+ clk_put(parent);
+ }
+}
+#else
+void __init at91_add_device_isi(struct isi_platform_data *data,
+ bool use_pck_as_mck) {}
+#endif
+
/* --------------------------------------------------------------------
* LCD Controller
diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c
index eec02cd57ced7fe60291f8938a64259f61b0f22a..1815152001f74c62d3d4dd409252a2c81aa197b0 100644
--- a/arch/arm/mach-at91/board-flexibity.c
+++ b/arch/arm/mach-at91/board-flexibity.c
@@ -1,7 +1,7 @@
/*
* linux/arch/arm/mach-at91/board-flexibity.c
*
- * Copyright (C) 2010 Flexibity
+ * Copyright (C) 2010-2011 Flexibity
* Copyright (C) 2005 SAN People
* Copyright (C) 2006 Atmel
*
@@ -62,6 +62,13 @@ static struct at91_udc_data __initdata flexibity_udc_data = {
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
+/* I2C devices */
+static struct i2c_board_info __initdata flexibity_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("ds1307", 0x68),
+ },
+};
+
/* SPI devices */
static struct spi_board_info flexibity_spi_devices[] = {
{ /* DataFlash chip */
@@ -141,6 +148,9 @@ static void __init flexibity_board_init(void)
at91_add_device_usbh(&flexibity_usbh_data);
/* USB Device */
at91_add_device_udc(&flexibity_udc_data);
+ /* I2C */
+ at91_add_device_i2c(flexibity_i2c_devices,
+ ARRAY_SIZE(flexibity_i2c_devices));
/* SPI */
at91_add_device_spi(flexibity_spi_devices,
ARRAY_SIZE(flexibity_spi_devices));
diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index ea0d1b9c2b7bd0327326a227509f7d4f1c896263..57497e2b8878cc11e34e95f4245674a81aa9b45f 100644
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -24,11 +24,13 @@
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/leds.h>
-#include <linux/clk.h>
#include <linux/atmel-mci.h>
+#include <linux/delay.h>
#include <mach/hardware.h>
#include <video/atmel_lcdc.h>
+#include <media/soc_camera.h>
+#include <media/atmel-isi.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
@@ -184,6 +186,71 @@ static void __init ek_add_device_nand(void)
}
+/*
+ * ISI
+ */
+static struct isi_platform_data __initdata isi_data = {
+ .frate = ISI_CFG1_FRATE_CAPTURE_ALL,
+ /* to use codec and preview path simultaneously */
+ .full_mode = 1,
+ .data_width_flags = ISI_DATAWIDTH_8 | ISI_DATAWIDTH_10,
+ /* ISI_MCK is provided by programmable clock or external clock */
+ .mck_hz = 25000000,
+};
+
+
+/*
+ * soc-camera OV2640
+ */
+#if defined(CONFIG_SOC_CAMERA_OV2640) || \
+ defined(CONFIG_SOC_CAMERA_OV2640_MODULE)
+static unsigned long isi_camera_query_bus_param(struct soc_camera_link *link)
+{
+ /* ISI board for ek using default 8-bits connection */
+ return SOCAM_DATAWIDTH_8;
+}
+
+static int i2c_camera_power(struct device *dev, int on)
+{
+ /* enable or disable the camera */
+ pr_debug("%s: %s the camera\n", __func__, on ? "ENABLE" : "DISABLE");
+ at91_set_gpio_output(AT91_PIN_PD13, !on);
+
+ if (!on)
+ goto out;
+
+ /* If enabled, give a reset impulse */
+ at91_set_gpio_output(AT91_PIN_PD12, 0);
+ msleep(20);
+ at91_set_gpio_output(AT91_PIN_PD12, 1);
+ msleep(100);
+
+out:
+ return 0;
+}
+
+static struct i2c_board_info i2c_camera = {
+ I2C_BOARD_INFO("ov2640", 0x30),
+};
+
+static struct soc_camera_link iclink_ov2640 = {
+ .bus_id = 0,
+ .board_info = &i2c_camera,
+ .i2c_adapter_id = 0,
+ .power = i2c_camera_power,
+ .query_bus_param = isi_camera_query_bus_param,
+};
+
+static struct platform_device isi_ov2640 = {
+ .name = "soc-camera-pdrv",
+ .id = 0,
+ .dev = {
+ .platform_data = &iclink_ov2640,
+ },
+};
+#endif
+
+
/*
* LCD Controller
*/
@@ -377,7 +444,12 @@ static struct gpio_led ek_pwm_led[] = {
#endif
};
-
+static struct platform_device *devices[] __initdata = {
+#if defined(CONFIG_SOC_CAMERA_OV2640) || \
+ defined(CONFIG_SOC_CAMERA_OV2640_MODULE)
+ &isi_ov2640,
+#endif
+};
static void __init ek_board_init(void)
{
@@ -399,6 +471,8 @@ static void __init ek_board_init(void)
ek_add_device_nand();
/* I2C */
at91_add_device_i2c(0, NULL, 0);
+ /* ISI, using programmable clock as ISI_MCK */
+ at91_add_device_isi(&isi_data, true);
/* LCD Controller */
at91_add_device_lcdc(&ek_lcdc_data);
/* Touch Screen */
@@ -410,6 +484,8 @@ static void __init ek_board_init(void)
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
+ /* Other platform devices */
+ platform_add_devices(devices, ARRAY_SIZE(devices));
}
MACHINE_START(AT91SAM9M10G45EK, "Atmel AT91SAM9M10G45-EK")
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
index 3b33f07b1e1189ab4a49644741715731b095461f..dc8d6d4f17cf71423960f9dce11f4941ae978e7c 100644
--- a/arch/arm/mach-at91/include/mach/board.h
+++ b/arch/arm/mach-at91/include/mach/board.h
@@ -107,6 +107,8 @@ struct atmel_nand_data {
u8 ale; /* address line number connected to ALE */
u8 cle; /* address line number connected to CLE */
u8 bus_width_16; /* buswidth is 16 bit */
+ u8 correction_cap; /* PMECC correction capability */
+ u16 sector_size; /* Sector size for PMECC */
struct mtd_partition *parts;
unsigned int num_parts;
};
@@ -179,7 +181,9 @@ extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
extern void __init at91_add_device_ac97(struct ac97c_platform_data *data);
/* ISI */
-extern void __init at91_add_device_isi(void);
+struct isi_platform_data;
+extern void __init at91_add_device_isi(struct isi_platform_data *data,
+ bool use_pck_as_mck);
/* Touchscreen Controller */
struct at91_tsadcc_data {
diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
index 98997c2da2626cdc560a593f23ceed9ca8cb2216..2bf7d6e2398981221a23ff0ae600d54a46704d5a 100644
--- a/arch/arm/mach-exynos/Kconfig
+++ b/arch/arm/mach-exynos/Kconfig
@@ -42,6 +42,7 @@ config SOC_EXYNOS4212
bool "SAMSUNG EXYNOS4212"
default y
depends on ARCH_EXYNOS4
+ select SAMSUNG_DMADEV
select S5P_PM if PM
select S5P_SLEEP if PM
help
@@ -51,6 +52,7 @@ config SOC_EXYNOS4412
bool "SAMSUNG EXYNOS4412"
default y
depends on ARCH_EXYNOS4
+ select SAMSUNG_DMADEV
help
Enable EXYNOS4412 SoC support
@@ -335,6 +337,7 @@ config MACH_SMDK4212
select SAMSUNG_DEV_BACKLIGHT
select SAMSUNG_DEV_KEYPAD
select SAMSUNG_DEV_PWM
+ select EXYNOS4_DEV_DMA
select EXYNOS4_SETUP_I2C1
select EXYNOS4_SETUP_I2C3
select EXYNOS4_SETUP_I2C7
diff --git a/arch/arm/mach-exynos/clock-exynos4.c b/arch/arm/mach-exynos/clock-exynos4.c
index 060dde7d7ad612047e18dd6a62131d60cbc8e22d..200159dcb341a640a191549688067e9c77b1a8ae 100644
--- a/arch/arm/mach-exynos/clock-exynos4.c
+++ b/arch/arm/mach-exynos/clock-exynos4.c
@@ -789,6 +789,13 @@ static struct clk exynos4_clk_pdma1 = {
.ctrlbit = (1 << 1),
};
+static struct clk exynos4_clk_mdma1 = {
+ .name = "dma",
+ .devname = "dma-pl330.2",
+ .enable = exynos4_clk_ip_image_ctrl,
+ .ctrlbit = ((1 << 8) | (1 << 5) | (1 << 2)),
+};
+
struct clk *exynos4_clkset_group_list[] = {
[0] = &clk_ext_xtal_mux,
[1] = &clk_xusbxti,
@@ -1307,6 +1314,7 @@ static struct clksrc_clk *exynos4_sysclks[] = {
static struct clk *exynos4_clk_cdev[] = {
&exynos4_clk_pdma0,
&exynos4_clk_pdma1,
+ &exynos4_clk_mdma1,
};
static struct clksrc_clk *exynos4_clksrc_cdev[] = {
@@ -1335,6 +1343,7 @@ static struct clk_lookup exynos4_clk_lookup[] = {
CLKDEV_INIT("s3c-sdhci.3", "mmc_busclk.2", &exynos4_clk_sclk_mmc3.clk),
CLKDEV_INIT("dma-pl330.0", "apb_pclk", &exynos4_clk_pdma0),
CLKDEV_INIT("dma-pl330.1", "apb_pclk", &exynos4_clk_pdma1),
+ CLKDEV_INIT("dma-pl330.2", "apb_pclk", &exynos4_clk_mdma1),
CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk0", &exynos4_clk_sclk_spi0.clk),
CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk0", &exynos4_clk_sclk_spi1.clk),
CLKDEV_INIT("s3c64xx-spi.2", "spi_busclk0", &exynos4_clk_sclk_spi2.clk),
diff --git a/arch/arm/mach-exynos/dma.c b/arch/arm/mach-exynos/dma.c
index 25f3ef2c36e5f3478ac131255b72a04d69940a85..13607c4328b3dd15f19da64e7a3e054552bbb96c 100644
--- a/arch/arm/mach-exynos/dma.c
+++ b/arch/arm/mach-exynos/dma.c
@@ -29,6 +29,7 @@
#include <asm/irq.h>
#include <plat/devs.h>
#include <plat/irqs.h>
+#include <plat/cpu.h>
#include <mach/map.h>
#include <mach/irqs.h>
@@ -36,7 +37,7 @@
static u64 dma_dmamask = DMA_BIT_MASK(32);
-static u8 pdma0_peri[] = {
+static u8 exynos4210_pdma0_peri[] = {
DMACH_PCM0_RX,
DMACH_PCM0_TX,
DMACH_PCM2_RX,
@@ -69,15 +70,47 @@ static u8 pdma0_peri[] = {
DMACH_AC97_PCMOUT,
};
-static struct dma_pl330_platdata exynos4_pdma0_pdata = {
- .nr_valid_peri = ARRAY_SIZE(pdma0_peri),
- .peri_id = pdma0_peri,
+static u8 exynos4212_pdma0_peri[] = {
+ DMACH_PCM0_RX,
+ DMACH_PCM0_TX,
+ DMACH_PCM2_RX,
+ DMACH_PCM2_TX,
+ DMACH_MIPI_HSI0,
+ DMACH_MIPI_HSI1,
+ DMACH_SPI0_RX,
+ DMACH_SPI0_TX,
+ DMACH_SPI2_RX,
+ DMACH_SPI2_TX,
+ DMACH_I2S0S_TX,
+ DMACH_I2S0_RX,
+ DMACH_I2S0_TX,
+ DMACH_I2S2_RX,
+ DMACH_I2S2_TX,
+ DMACH_UART0_RX,
+ DMACH_UART0_TX,
+ DMACH_UART2_RX,
+ DMACH_UART2_TX,
+ DMACH_UART4_RX,
+ DMACH_UART4_TX,
+ DMACH_SLIMBUS0_RX,
+ DMACH_SLIMBUS0_TX,
+ DMACH_SLIMBUS2_RX,
+ DMACH_SLIMBUS2_TX,
+ DMACH_SLIMBUS4_RX,
+ DMACH_SLIMBUS4_TX,
+ DMACH_AC97_MICIN,
+ DMACH_AC97_PCMIN,
+ DMACH_AC97_PCMOUT,
+ DMACH_MIPI_HSI4,
+ DMACH_MIPI_HSI5,
};
+struct dma_pl330_platdata exynos4_pdma0_pdata;
+
static AMBA_AHB_DEVICE(exynos4_pdma0, "dma-pl330.0", 0x00041330,
EXYNOS4_PA_PDMA0, {IRQ_PDMA0}, &exynos4_pdma0_pdata);
-static u8 pdma1_peri[] = {
+static u8 exynos4210_pdma1_peri[] = {
DMACH_PCM0_RX,
DMACH_PCM0_TX,
DMACH_PCM1_RX,
@@ -105,19 +138,84 @@ static u8 pdma1_peri[] = {
DMACH_SLIMBUS5_TX,
};
-static struct dma_pl330_platdata exynos4_pdma1_pdata = {
- .nr_valid_peri = ARRAY_SIZE(pdma1_peri),
- .peri_id = pdma1_peri,
+static u8 exynos4212_pdma1_peri[] = {
+ DMACH_PCM0_RX,
+ DMACH_PCM0_TX,
+ DMACH_PCM1_RX,
+ DMACH_PCM1_TX,
+ DMACH_MIPI_HSI2,
+ DMACH_MIPI_HSI3,
+ DMACH_SPI1_RX,
+ DMACH_SPI1_TX,
+ DMACH_I2S0S_TX,
+ DMACH_I2S0_RX,
+ DMACH_I2S0_TX,
+ DMACH_I2S1_RX,
+ DMACH_I2S1_TX,
+ DMACH_UART0_RX,
+ DMACH_UART0_TX,
+ DMACH_UART1_RX,
+ DMACH_UART1_TX,
+ DMACH_UART3_RX,
+ DMACH_UART3_TX,
+ DMACH_SLIMBUS1_RX,
+ DMACH_SLIMBUS1_TX,
+ DMACH_SLIMBUS3_RX,
+ DMACH_SLIMBUS3_TX,
+ DMACH_SLIMBUS5_RX,
+ DMACH_SLIMBUS5_TX,
+ DMACH_SLIMBUS0AUX_RX,
+ DMACH_SLIMBUS0AUX_TX,
+ DMACH_SPDIF,
+ DMACH_MIPI_HSI6,
+ DMACH_MIPI_HSI7,
};
+static struct dma_pl330_platdata exynos4_pdma1_pdata;
+
static AMBA_AHB_DEVICE(exynos4_pdma1, "dma-pl330.1", 0x00041330,
EXYNOS4_PA_PDMA1, {IRQ_PDMA1}, &exynos4_pdma1_pdata);
+static u8 mdma_peri[] = {
+ DMACH_MTOM_0,
+ DMACH_MTOM_1,
+ DMACH_MTOM_2,
+ DMACH_MTOM_3,
+ DMACH_MTOM_4,
+ DMACH_MTOM_5,
+ DMACH_MTOM_6,
+ DMACH_MTOM_7,
+};
+
+static struct dma_pl330_platdata exynos4_mdma1_pdata = {
+ .nr_valid_peri = ARRAY_SIZE(mdma_peri),
+ .peri_id = mdma_peri,
+};
+
+static AMBA_AHB_DEVICE(exynos4_mdma1, "dma-pl330.2", 0x00041330,
+ EXYNOS4_PA_MDMA1, {IRQ_MDMA1}, &exynos4_mdma1_pdata);
+
static int __init exynos4_dma_init(void)
{
if (of_have_populated_dt())
return 0;
+ if (soc_is_exynos4210()) {
+ exynos4_pdma0_pdata.nr_valid_peri =
+ ARRAY_SIZE(exynos4210_pdma0_peri);
+ exynos4_pdma0_pdata.peri_id = exynos4210_pdma0_peri;
+ exynos4_pdma1_pdata.nr_valid_peri =
+ ARRAY_SIZE(exynos4210_pdma1_peri);
+ exynos4_pdma1_pdata.peri_id = exynos4210_pdma1_peri;
+ } else if (soc_is_exynos4212() || soc_is_exynos4412()) {
+ exynos4_pdma0_pdata.nr_valid_peri =
+ ARRAY_SIZE(exynos4212_pdma0_peri);
+ exynos4_pdma0_pdata.peri_id = exynos4212_pdma0_peri;
+ exynos4_pdma1_pdata.nr_valid_peri =
+ ARRAY_SIZE(exynos4212_pdma1_peri);
+ exynos4_pdma1_pdata.peri_id = exynos4212_pdma1_peri;
+ }
+
dma_cap_set(DMA_SLAVE, exynos4_pdma0_pdata.cap_mask);
dma_cap_set(DMA_CYCLIC, exynos4_pdma0_pdata.cap_mask);
amba_device_register(&exynos4_pdma0_device, &iomem_resource);
@@ -126,6 +224,9 @@ static int __init exynos4_dma_init(void)
dma_cap_set(DMA_CYCLIC, exynos4_pdma1_pdata.cap_mask);
amba_device_register(&exynos4_pdma1_device, &iomem_resource);
+ dma_cap_set(DMA_MEMCPY, exynos4_mdma1_pdata.cap_mask);
+ amba_device_register(&exynos4_mdma1_device, &iomem_resource);
+
return 0;
}
arch_initcall(exynos4_dma_init);
diff --git a/arch/arm/mach-exynos/include/mach/irqs.h b/arch/arm/mach-exynos/include/mach/irqs.h
index f77bce04789aadc8ade57f9ed88f16e85f31e4a2..1d401c957835f666e9c86980efca8935d1f570b1 100644
--- a/arch/arm/mach-exynos/include/mach/irqs.h
+++ b/arch/arm/mach-exynos/include/mach/irqs.h
@@ -43,6 +43,8 @@
#define IRQ_EINT15 IRQ_SPI(31)
#define IRQ_EINT16_31 IRQ_SPI(32)
+#define IRQ_MDMA0 IRQ_SPI(33)
+#define IRQ_MDMA1 IRQ_SPI(34)
#define IRQ_PDMA0 IRQ_SPI(35)
#define IRQ_PDMA1 IRQ_SPI(36)
#define IRQ_TIMER0_VIC IRQ_SPI(37)
diff --git a/arch/arm/mach-exynos/include/mach/map.h b/arch/arm/mach-exynos/include/mach/map.h
index a8cd65fcc685d8e818c3665c1429ef91ebcda168..609127df9b02f3fe0aedce427ecf14a166c5dcb3 100644
--- a/arch/arm/mach-exynos/include/mach/map.h
+++ b/arch/arm/mach-exynos/include/mach/map.h
@@ -72,7 +72,8 @@
#define EXYNOS4_PA_TWD 0x10500600
#define EXYNOS4_PA_L2CC 0x10502000
-#define EXYNOS4_PA_MDMA 0x10810000
+#define EXYNOS4_PA_MDMA0 0x10810000
+#define EXYNOS4_PA_MDMA1 0x12840000
#define EXYNOS4_PA_PDMA0 0x12680000
#define EXYNOS4_PA_PDMA1 0x12690000
diff --git a/arch/arm/mach-exynos/mach-nuri.c b/arch/arm/mach-exynos/mach-nuri.c
index 191f5c675fe1b0ed7e44646a9e7c32f73126764b..82ea6fccfb3450e54487b24ead9e12c2af589e9b 100644
--- a/arch/arm/mach-exynos/mach-nuri.c
+++ b/arch/arm/mach-exynos/mach-nuri.c
@@ -117,7 +117,7 @@ static struct s3c_sdhci_platdata nuri_hsmmc0_data __initdata = {
};
static struct regulator_consumer_supply emmc_supplies[] = {
- REGULATOR_SUPPLY("vmmc", "s3c-sdhci.0"),
+ REGULATOR_SUPPLY("vmmc", "exynos4-sdhci.0"),
REGULATOR_SUPPLY("vmmc", "dw_mmc"),
};
@@ -418,7 +418,7 @@ static struct regulator_consumer_supply __initdata max8997_ldo12_[] = {
REGULATOR_SUPPLY("vddio", "6-003c"), /* HDC802 */
};
static struct regulator_consumer_supply __initdata max8997_ldo13_[] = {
- REGULATOR_SUPPLY("vmmc", "s3c-sdhci.2"), /* TFLASH */
+ REGULATOR_SUPPLY("vmmc", "exynos4-sdhci.2"), /* TFLASH */
};
static struct regulator_consumer_supply __initdata max8997_ldo14_[] = {
REGULATOR_SUPPLY("inmotor", "max8997-haptic"),
diff --git a/arch/arm/mach-exynos/mach-universal_c210.c b/arch/arm/mach-exynos/mach-universal_c210.c
index 0b944eb66ebd74e339fc66661fd0f21cd6098084..28658da9f4230e8d17c000e4fec5ca696fb39373 100644
--- a/arch/arm/mach-exynos/mach-universal_c210.c
+++ b/arch/arm/mach-exynos/mach-universal_c210.c
@@ -752,7 +752,7 @@ static struct s3c_sdhci_platdata universal_hsmmc0_data __initdata = {
};
static struct regulator_consumer_supply mmc0_supplies[] = {
- REGULATOR_SUPPLY("vmmc", "s3c-sdhci.0"),
+ REGULATOR_SUPPLY("vmmc", "exynos4-sdhci.0"),
};
static struct regulator_init_data mmc0_fixed_voltage_init_data = {
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 37a5d715a6c2627efcce000ed1e641b231bc03e0..feeebde71deb7ac92c64cfdaa57d091e50355d37 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -298,6 +298,7 @@ config MACH_MX27_3DS
select IMX_HAVE_PLATFORM_IMX_I2C
select IMX_HAVE_PLATFORM_IMX_KEYPAD
select IMX_HAVE_PLATFORM_IMX_UART
+ select IMX_HAVE_PLATFORM_MX2_CAMERA
select IMX_HAVE_PLATFORM_MXC_EHCI
select IMX_HAVE_PLATFORM_MXC_MMC
select IMX_HAVE_PLATFORM_SPI_IMX
diff --git a/arch/arm/mach-imx/clock-imx6q.c b/arch/arm/mach-imx/clock-imx6q.c
index 2d88f8b9a454994bee6841cda4828d81286bac5e..111c328f542004fcec8c6391d8f35fac974f1886 100644
--- a/arch/arm/mach-imx/clock-imx6q.c
+++ b/arch/arm/mach-imx/clock-imx6q.c
@@ -329,6 +329,12 @@
#define BM_CLPCR_MASK_SCU_IDLE (0x1 << 26)
#define BM_CLPCR_MASK_L2CC_IDLE (0x1 << 27)
+#define BP_CCOSR_CKO1_EN 7
+#define BP_CCOSR_CKO1_PODF 4
+#define BM_CCOSR_CKO1_PODF (0x7 << 4)
+#define BP_CCOSR_CKO1_SEL 0
+#define BM_CCOSR_CKO1_SEL (0xf << 0)
+
#define FREQ_480M 480000000
#define FREQ_528M 528000000
#define FREQ_594M 594000000
@@ -393,6 +399,7 @@ static struct clk ipu1_di1_clk;
static struct clk ipu2_di0_clk;
static struct clk ipu2_di1_clk;
static struct clk enfc_clk;
+static struct clk cko1_clk;
static struct clk dummy_clk = {};
static unsigned long external_high_reference;
@@ -938,6 +945,24 @@ static void _clk_disable(struct clk *clk)
writel_relaxed(reg, clk->enable_reg);
}
+static int _clk_enable_1b(struct clk *clk)
+{
+ u32 reg;
+ reg = readl_relaxed(clk->enable_reg);
+ reg |= 0x1 << clk->enable_shift;
+ writel_relaxed(reg, clk->enable_reg);
+
+ return 0;
+}
+
+static void _clk_disable_1b(struct clk *clk)
+{
+ u32 reg;
+ reg = readl_relaxed(clk->enable_reg);
+ reg &= ~(0x1 << clk->enable_shift);
+ writel_relaxed(reg, clk->enable_reg);
+}
+
struct divider {
struct clk *clk;
void __iomem *reg;
@@ -983,6 +1008,7 @@ DEF_CLK_DIV1(ipu2_di0_pre_div, &ipu2_di0_pre_clk, CSCDR2, IPU2_DI0_PRE);
DEF_CLK_DIV1(ipu2_di1_pre_div, &ipu2_di1_pre_clk, CSCDR2, IPU2_DI1_PRE);
DEF_CLK_DIV1(ipu1_div, &ipu1_clk, CSCDR3, IPU1_HSP);
DEF_CLK_DIV1(ipu2_div, &ipu2_clk, CSCDR3, IPU2_HSP);
+DEF_CLK_DIV1(cko1_div, &cko1_clk, CCOSR, CKO1);
#define DEF_CLK_DIV2(d, c, r, b) \
static struct divider d = { \
@@ -1038,6 +1064,7 @@ static struct divider *dividers[] = {
&enfc_div,
&spdif_div,
&asrc_serial_div,
+ &cko1_div,
};
static unsigned long ldb_di_clk_get_rate(struct clk *clk)
@@ -1625,6 +1652,32 @@ DEF_IPU_DI_MUX(CSCDR2, 2, 1);
DEF_IPU_MUX(1);
DEF_IPU_MUX(2);
+static struct multiplexer cko1_mux = {
+ .clk = &cko1_clk,
+ .reg = CCOSR,
+ .bp = BP_CCOSR_CKO1_SEL,
+ .bm = BM_CCOSR_CKO1_SEL,
+ .parents = {
+ &pll3_usb_otg,
+ &pll2_bus,
+ &pll1_sys,
+ &pll5_video,
+ &dummy_clk,
+ &axi_clk,
+ &enfc_clk,
+ &ipu1_di0_clk,
+ &ipu1_di1_clk,
+ &ipu2_di0_clk,
+ &ipu2_di1_clk,
+ &ahb_clk,
+ &ipg_clk,
+ &ipg_perclk,
+ &ckil_clk,
+ &pll4_audio,
+ NULL
+ },
+};
+
static struct multiplexer *multiplexers[] = {
&axi_mux,
&periph_mux,
@@ -1667,6 +1720,7 @@ static struct multiplexer *multiplexers[] = {
&ipu2_di1_mux,
&ipu1_mux,
&ipu2_mux,
+ &cko1_mux,
};
static int _clk_set_parent(struct clk *clk, struct clk *parent)
@@ -1690,7 +1744,7 @@ static int _clk_set_parent(struct clk *clk, struct clk *parent)
break;
i++;
}
- if (!m->parents[i])
+ if (!m->parents[i] || m->parents[i] == &dummy_clk)
return -EINVAL;
val = readl_relaxed(m->reg);
@@ -1745,6 +1799,20 @@ DEF_NG_CLK(asrc_serial_clk, &pll3_usb_otg);
.secondary = s, \
}
+#define DEF_CLK_1B(name, er, es, p, s) \
+ static struct clk name = { \
+ .enable_reg = er, \
+ .enable_shift = es, \
+ .enable = _clk_enable_1b, \
+ .disable = _clk_disable_1b, \
+ .get_rate = _clk_get_rate, \
+ .set_rate = _clk_set_rate, \
+ .round_rate = _clk_round_rate, \
+ .set_parent = _clk_set_parent, \
+ .parent = p, \
+ .secondary = s, \
+ }
+
DEF_CLK(aips_tz1_clk, CCGR0, CG0, &ahb_clk, NULL);
DEF_CLK(aips_tz2_clk, CCGR0, CG1, &ahb_clk, NULL);
DEF_CLK(apbh_dma_clk, CCGR0, CG2, &ahb_clk, NULL);
@@ -1811,6 +1879,7 @@ DEF_CLK(usdhc4_clk, CCGR6, CG4, &pll2_pfd_400m, NULL);
DEF_CLK(emi_slow_clk, CCGR6, CG5, &axi_clk, NULL);
DEF_CLK(vdo_axi_clk, CCGR6, CG6, &axi_clk, NULL);
DEF_CLK(vpu_clk, CCGR6, CG7, &axi_clk, NULL);
+DEF_CLK_1B(cko1_clk, CCOSR, BP_CCOSR_CKO1_EN, &pll2_bus, NULL);
static int pcie_clk_enable(struct clk *clk)
{
@@ -1922,6 +1991,7 @@ static struct clk_lookup lookups[] = {
_REGISTER_CLOCK(NULL, "gpmi_io_clk", gpmi_io_clk),
_REGISTER_CLOCK(NULL, "usboh3_clk", usboh3_clk),
_REGISTER_CLOCK(NULL, "sata_clk", sata_clk),
+ _REGISTER_CLOCK(NULL, "cko1_clk", cko1_clk),
};
int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode)
@@ -2029,6 +2099,8 @@ int __init mx6q_clocks_init(void)
clk_set_rate(&usdhc3_clk, 49500000);
clk_set_rate(&usdhc4_clk, 49500000);
+ clk_set_parent(&cko1_clk, &ahb_clk);
+
np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-gpt");
base = of_iomap(np, 0);
WARN_ON(!base);
diff --git a/arch/arm/mach-imx/lluart.c b/arch/arm/mach-imx/lluart.c
index d4ab6f29a7664250b0a3d11b40f273dee3de055b..0213f8dcee81752291551bf37103b1b16a3a664f 100644
--- a/arch/arm/mach-imx/lluart.c
+++ b/arch/arm/mach-imx/lluart.c
@@ -17,7 +17,7 @@
#include <mach/hardware.h>
static struct map_desc imx_lluart_desc = {
-#ifdef CONFIG_DEBUG_IMX6Q_UART
+#ifdef CONFIG_DEBUG_IMX6Q_UART4
.virtual = MX6Q_IO_P2V(MX6Q_UART4_BASE_ADDR),
.pfn = __phys_to_pfn(MX6Q_UART4_BASE_ADDR),
.length = MX6Q_UART4_SIZE,
diff --git a/arch/arm/mach-imx/mach-mx21ads.c b/arch/arm/mach-imx/mach-mx21ads.c
index 8d9f95514b1f1410997b7ecadfcc3918b9b5f613..e432d4acee1fb72711485002f3108c5b33575d99 100644
--- a/arch/arm/mach-imx/mach-mx21ads.c
+++ b/arch/arm/mach-imx/mach-mx21ads.c
@@ -37,8 +37,8 @@
#define MX21ADS_REG_ADDR(offset) (void __force __iomem *) \
(MX21ADS_MMIO_BASE_ADDR + (offset))
+#define MX21ADS_CS8900A_MMIO_SIZE 0x200000
#define MX21ADS_CS8900A_IRQ IRQ_GPIOE(11)
-#define MX21ADS_CS8900A_IOBASE_REG MX21ADS_REG_ADDR(0x000000)
#define MX21ADS_ST16C255_IOBASE_REG MX21ADS_REG_ADDR(0x200000)
#define MX21ADS_VERSION_REG MX21ADS_REG_ADDR(0x400000)
#define MX21ADS_IO_REG MX21ADS_REG_ADDR(0x800000)
@@ -159,6 +159,18 @@ static struct platform_device mx21ads_nor_mtd_device = {
.resource = &mx21ads_flash_resource,
};
+static const struct resource mx21ads_cs8900_resources[] __initconst = {
+ DEFINE_RES_MEM(MX21_CS1_BASE_ADDR, MX21ADS_CS8900A_MMIO_SIZE),
+ DEFINE_RES_IRQ(MX21ADS_CS8900A_IRQ),
+};
+
+static const struct platform_device_info mx21ads_cs8900_devinfo __initconst = {
+ .name = "cs89x0",
+ .id = 0,
+ .res = mx21ads_cs8900_resources,
+ .num_res = ARRAY_SIZE(mx21ads_cs8900_resources),
+};
+
static const struct imxuart_platform_data uart_pdata_rts __initconst = {
.flags = IMXUART_HAVE_RTSCTS,
};
@@ -292,6 +304,8 @@ static void __init mx21ads_board_init(void)
imx21_add_mxc_nand(&mx21ads_nand_board_info);
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
+ platform_device_register_full(
+ (struct platform_device_info *)&mx21ads_cs8900_devinfo);
}
static void __init mx21ads_timer_init(void)
diff --git a/arch/arm/mach-imx/mach-mx27_3ds.c b/arch/arm/mach-imx/mach-mx27_3ds.c
index 18f35816706a1e77771d2a57992bee32a006c694..c6d385c522576f1052eeb474fc2d69a86faa7a0e 100644
--- a/arch/arm/mach-imx/mach-mx27_3ds.c
+++ b/arch/arm/mach-imx/mach-mx27_3ds.c
@@ -31,6 +31,8 @@
#include <linux/regulator/machine.h>
#include <linux/spi/l4f00242t03.h>
+#include <media/soc_camera.h>
+
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
@@ -52,6 +54,8 @@
#define SD1_CD IMX_GPIO_NR(2, 26)
#define LCD_RESET IMX_GPIO_NR(1, 3)
#define LCD_ENABLE IMX_GPIO_NR(1, 31)
+#define CSI_PWRDWN IMX_GPIO_NR(4, 19)
+#define CSI_RESET IMX_GPIO_NR(3, 6)
static const int mx27pdk_pins[] __initconst = {
/* UART1 */
@@ -141,6 +145,26 @@ static const int mx27pdk_pins[] __initconst = {
PA30_PF_CONTRAST,
LCD_ENABLE | GPIO_GPIO | GPIO_OUT,
LCD_RESET | GPIO_GPIO | GPIO_OUT,
+ /* CSI */
+ PB10_PF_CSI_D0,
+ PB11_PF_CSI_D1,
+ PB12_PF_CSI_D2,
+ PB13_PF_CSI_D3,
+ PB14_PF_CSI_D4,
+ PB15_PF_CSI_MCLK,
+ PB16_PF_CSI_PIXCLK,
+ PB17_PF_CSI_D5,
+ PB18_PF_CSI_D6,
+ PB19_PF_CSI_D7,
+ PB20_PF_CSI_VSYNC,
+ PB21_PF_CSI_HSYNC,
+ CSI_PWRDWN | GPIO_GPIO | GPIO_OUT,
+ CSI_RESET | GPIO_GPIO | GPIO_OUT,
+};
+
+static struct gpio mx27_3ds_camera_gpios[] = {
+ { CSI_PWRDWN, GPIOF_OUT_INIT_HIGH, "camera-power" },
+ { CSI_RESET, GPIOF_OUT_INIT_HIGH, "camera-reset" },
};
static const struct imxuart_platform_data uart_pdata __initconst = {
@@ -242,6 +266,7 @@ static struct regulator_init_data gpo_init = {
static struct regulator_consumer_supply vmmc1_consumers[] = {
REGULATOR_SUPPLY("vcore", "spi0.0"),
+ REGULATOR_SUPPLY("cmos_2v8", "soc-camera-pdrv.0"),
};
static struct regulator_init_data vmmc1_init = {
@@ -270,6 +295,22 @@ static struct regulator_init_data vgen_init = {
.consumer_supplies = vgen_consumers,
};
+static struct regulator_consumer_supply vvib_consumers[] = {
+ REGULATOR_SUPPLY("cmos_vcore", "soc-camera-pdrv.0"),
+};
+
+static struct regulator_init_data vvib_init = {
+ .constraints = {
+ .min_uV = 1300000,
+ .max_uV = 1300000,
+ .apply_uV = 1,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(vvib_consumers),
+ .consumer_supplies = vvib_consumers,
+};
+
static struct mc13xxx_regulator_init_data mx27_3ds_regulators[] = {
{
.id = MC13783_REG_VMMC1,
@@ -283,6 +324,9 @@ static struct mc13xxx_regulator_init_data mx27_3ds_regulators[] = {
}, {
.id = MC13783_REG_GPO3, /* Turn on 3.3V */
.init_data = &gpo_init,
+ }, {
+ .id = MC13783_REG_VVIB, /* Power OV2640 */
+ .init_data = &vvib_init,
},
};
@@ -311,6 +355,51 @@ static const struct spi_imx_master spi2_pdata __initconst = {
.num_chipselect = ARRAY_SIZE(spi2_chipselect),
};
+static int mx27_3ds_camera_power(struct device *dev, int on)
+{
+ /* enable or disable the camera */
+ pr_debug("%s: %s the camera\n", __func__, on ? "ENABLE" : "DISABLE");
+ gpio_set_value(CSI_PWRDWN, on ? 0 : 1);
+
+ if (!on)
+ goto out;
+
+ /* If enabled, give a reset impulse */
+ gpio_set_value(CSI_RESET, 0);
+ msleep(20);
+ gpio_set_value(CSI_RESET, 1);
+ msleep(100);
+
+out:
+ return 0;
+}
+
+static struct i2c_board_info mx27_3ds_i2c_camera = {
+ I2C_BOARD_INFO("ov2640", 0x30),
+};
+
+static struct regulator_bulk_data mx27_3ds_camera_regs[] = {
+ { .supply = "cmos_vcore" },
+ { .supply = "cmos_2v8" },
+};
+
+static struct soc_camera_link iclink_ov2640 = {
+ .bus_id = 0,
+ .board_info = &mx27_3ds_i2c_camera,
+ .i2c_adapter_id = 0,
+ .power = mx27_3ds_camera_power,
+ .regulators = mx27_3ds_camera_regs,
+ .num_regulators = ARRAY_SIZE(mx27_3ds_camera_regs),
+};
+
+static struct platform_device mx27_3ds_ov2640 = {
+ .name = "soc-camera-pdrv",
+ .id = 0,
+ .dev = {
+ .platform_data = &iclink_ov2640,
+ },
+};
+
static struct imx_fb_videomode mx27_3ds_modes[] = {
{ /* 480x640 @ 60 Hz */
.mode = {
@@ -367,12 +456,21 @@ static struct spi_board_info mx27_3ds_spi_devs[] __initdata = {
},
};
+static struct platform_device *devices[] __initdata = {
+ &mx27_3ds_ov2640,
+};
+
+static const struct mx2_camera_platform_data mx27_3ds_cam_pdata __initconst = {
+ .clk = 26000000,
+};
+
static const struct imxi2c_platform_data mx27_3ds_i2c0_data __initconst = {
.bitrate = 100000,
};
static void __init mx27pdk_init(void)
{
+ int ret;
imx27_soc_init();
mxc_gpio_setup_multiple_pins(mx27pdk_pins, ARRAY_SIZE(mx27pdk_pins),
@@ -404,7 +502,17 @@ static void __init mx27pdk_init(void)
if (mxc_expio_init(MX27_CS5_BASE_ADDR, EXPIO_PARENT_INT))
pr_warn("Init of the debugboard failed, all devices on the debugboard are unusable.\n");
imx27_add_imx_i2c(0, &mx27_3ds_i2c0_data);
+ platform_add_devices(devices, ARRAY_SIZE(devices));
imx27_add_imx_fb(&mx27_3ds_fb_data);
+
+ ret = gpio_request_array(mx27_3ds_camera_gpios,
+ ARRAY_SIZE(mx27_3ds_camera_gpios));
+ if (ret) {
+ pr_err("Failed to request camera gpios");
+ iclink_ov2640.power = NULL;
+ }
+
+ imx27_add_mx2_camera(&mx27_3ds_cam_pdata);
}
static void __init mx27pdk_timer_init(void)
diff --git a/arch/arm/mach-imx/mach-mx31ads.c b/arch/arm/mach-imx/mach-mx31ads.c
index 4917aab0e2539609a57bbcdc94bf8b24fccb37aa..4518e544822731c19b941927067265184c59ff0b 100644
--- a/arch/arm/mach-imx/mach-mx31ads.c
+++ b/arch/arm/mach-imx/mach-mx31ads.c
@@ -28,7 +28,6 @@
#include <asm/memory.h>
#include <asm/mach/map.h>
#include <mach/common.h>
-#include <mach/board-mx31ads.h>
#include <mach/iomux-mx3.h>
#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
@@ -39,6 +38,9 @@
#include "devices-imx31.h"
+/* Base address of PBC controller */
+#define PBC_BASE_ADDRESS MX31_CS4_BASE_ADDR_VIRT
+
/* PBC Board interrupt status register */
#define PBC_INTSTATUS 0x000016
@@ -62,6 +64,7 @@
#define PBC_INTMASK_CLEAR_REG (PBC_INTMASK_CLEAR + PBC_BASE_ADDRESS)
#define EXPIO_PARENT_INT IOMUX_TO_IRQ(MX31_PIN_GPIO1_4)
+#define MXC_EXP_IO_BASE MXC_BOARD_IRQ_START
#define MXC_IRQ_TO_EXPIO(irq) ((irq) - MXC_EXP_IO_BASE)
#define EXPIO_INT_XUART_INTA (MXC_EXP_IO_BASE + 10)
@@ -69,6 +72,10 @@
#define MXC_MAX_EXP_IO_LINES 16
+/* CS8900 */
+#define EXPIO_INT_ENET_INT (MXC_EXP_IO_BASE + 8)
+#define CS4_CS8900_MMIO_START 0x20000
+
/*
* The serial port definition structure.
*/
@@ -101,11 +108,29 @@ static struct platform_device serial_device = {
},
};
+static const struct resource mx31ads_cs8900_resources[] __initconst = {
+ DEFINE_RES_MEM(MX31_CS4_BASE_ADDR + CS4_CS8900_MMIO_START, SZ_64K),
+ DEFINE_RES_IRQ(EXPIO_INT_ENET_INT),
+};
+
+static const struct platform_device_info mx31ads_cs8900_devinfo __initconst = {
+ .name = "cs89x0",
+ .id = 0,
+ .res = mx31ads_cs8900_resources,
+ .num_res = ARRAY_SIZE(mx31ads_cs8900_resources),
+};
+
static int __init mxc_init_extuart(void)
{
return platform_device_register(&serial_device);
}
+static void __init mxc_init_ext_ethernet(void)
+{
+ platform_device_register_full(
+ (struct platform_device_info *)&mx31ads_cs8900_devinfo);
+}
+
static const struct imxuart_platform_data uart_pdata __initconst = {
.flags = IMXUART_HAVE_RTSCTS,
};
@@ -492,12 +517,15 @@ static void __init mxc_init_audio(void)
mxc_iomux_setup_multiple_pins(ssi_pins, ARRAY_SIZE(ssi_pins), "ssi");
}
-/* static mappings */
+/*
+ * Static mappings, starting from the CS4 start address up to the start address
+ * of the CS8900.
+ */
static struct map_desc mx31ads_io_desc[] __initdata = {
{
.virtual = MX31_CS4_BASE_ADDR_VIRT,
.pfn = __phys_to_pfn(MX31_CS4_BASE_ADDR),
- .length = MX31_CS4_SIZE / 2,
+ .length = CS4_CS8900_MMIO_START,
.type = MT_DEVICE
},
};
@@ -522,6 +550,7 @@ static void __init mx31ads_init(void)
mxc_init_imx_uart();
mxc_init_i2c();
mxc_init_audio();
+ mxc_init_ext_ethernet();
}
static void __init mx31ads_timer_init(void)
diff --git a/arch/arm/mach-imx/mach-mx31moboard.c b/arch/arm/mach-imx/mach-mx31moboard.c
index c0511fb1a5f9dffb860b584421fa421c4cc31ebc..f17a15f28316519a1dd01f793742ca1293286df2 100644
--- a/arch/arm/mach-imx/mach-mx31moboard.c
+++ b/arch/arm/mach-imx/mach-mx31moboard.c
@@ -507,7 +507,7 @@ static void mx31moboard_poweroff(void)
struct clk *clk = clk_get_sys("imx2-wdt.0", NULL);
if (!IS_ERR(clk))
- clk_enable(clk);
+ clk_prepare_enable(clk);
mxc_iomux_mode(MX31_PIN_WATCHDOG_RST__WATCHDOG_RST);
diff --git a/arch/arm/mach-imx/pm-imx5.c b/arch/arm/mach-imx/pm-imx5.c
index 6dc0934480577363a2d49a4a5646d69d6cc62729..e26a9cb05ed811098e25244e58349b094ba0dc7b 100644
--- a/arch/arm/mach-imx/pm-imx5.c
+++ b/arch/arm/mach-imx/pm-imx5.c
@@ -89,7 +89,7 @@ void mx5_cpu_lp_set(enum mxc_cpu_pwr_mode mode)
static int mx5_suspend_prepare(void)
{
- return clk_enable(gpc_dvfs_clk);
+ return clk_prepare_enable(gpc_dvfs_clk);
}
static int mx5_suspend_enter(suspend_state_t state)
@@ -119,7 +119,7 @@ static int mx5_suspend_enter(suspend_state_t state)
static void mx5_suspend_finish(void)
{
- clk_disable(gpc_dvfs_clk);
+ clk_disable_unprepare(gpc_dvfs_clk);
}
static int mx5_pm_valid(suspend_state_t state)
diff --git a/arch/arm/mach-lpc32xx/clock.c b/arch/arm/mach-lpc32xx/clock.c
index 0e01bf44479c27a4f45ba037848354845e0aa8d3..f55c772d1816009365756d0d5c09da1f0c81569a 100644
--- a/arch/arm/mach-lpc32xx/clock.c
+++ b/arch/arm/mach-lpc32xx/clock.c
@@ -721,6 +721,41 @@ static struct clk clk_tsc = {
.get_rate = local_return_parent_rate,
};
+static int adc_onoff_enable(struct clk *clk, int enable)
+{
+ u32 tmp;
+ u32 divider;
+
+ /* Use PERIPH_CLOCK */
+ tmp = __raw_readl(LPC32XX_CLKPWR_ADC_CLK_CTRL_1);
+ tmp |= LPC32XX_CLKPWR_ADCCTRL1_PCLK_SEL;
+ /*
+ * Set clock divider so that we have equal to or less than
+ * 4.5MHz clock at ADC
+ */
+ divider = clk->get_rate(clk) / 4500000 + 1;
+ tmp |= divider;
+ __raw_writel(tmp, LPC32XX_CLKPWR_ADC_CLK_CTRL_1);
+
+ /* synchronize rate of this clock w/ actual HW setting */
+ clk->rate = clk->get_rate(clk->parent) / divider;
+
+ if (enable == 0)
+ __raw_writel(0, clk->enable_reg);
+ else
+ __raw_writel(clk->enable_mask, clk->enable_reg);
+
+ return 0;
+}
+
+static struct clk clk_adc = {
+ .parent = &clk_pclk,
+ .enable = adc_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_ADC_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_ADC32CLKCTRL_CLK_EN,
+ .get_rate = local_return_parent_rate,
+};
+
static int mmc_onoff_enable(struct clk *clk, int enable)
{
u32 tmp;
@@ -1055,6 +1090,7 @@ static struct clk_lookup lookups[] = {
_REGISTER_CLOCK("dev:ssp1", NULL, clk_ssp1)
_REGISTER_CLOCK("lpc32xx_keys.0", NULL, clk_kscan)
_REGISTER_CLOCK("lpc32xx-nand.0", "nand_ck", clk_nand)
+ _REGISTER_CLOCK("lpc32xx-adc", NULL, clk_adc)
_REGISTER_CLOCK(NULL, "i2s0_ck", clk_i2s0)
_REGISTER_CLOCK(NULL, "i2s1_ck", clk_i2s1)
_REGISTER_CLOCK("ts-lpc32xx", NULL, clk_tsc)
diff --git a/arch/arm/mach-lpc32xx/common.c b/arch/arm/mach-lpc32xx/common.c
index 369b152896cd7d7c4311a5766ded9428b2e74c87..6c76bb36559ba0ea32356b6e34cb4a6d735a1ad7 100644
--- a/arch/arm/mach-lpc32xx/common.c
+++ b/arch/arm/mach-lpc32xx/common.c
@@ -137,6 +137,28 @@ struct platform_device lpc32xx_rtc_device = {
.resource = lpc32xx_rtc_resources,
};
+/*
+ * ADC support
+ */
+static struct resource adc_resources[] = {
+ {
+ .start = LPC32XX_ADC_BASE,
+ .end = LPC32XX_ADC_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_LPC32XX_TS_IRQ,
+ .end = IRQ_LPC32XX_TS_IRQ,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device lpc32xx_adc_device = {
+ .name = "lpc32xx-adc",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(adc_resources),
+ .resource = adc_resources,
+};
+
/*
* Returns the unique ID for the device
*/
diff --git a/arch/arm/mach-lpc32xx/common.h b/arch/arm/mach-lpc32xx/common.h
index 75640bfb097fab64de85e38a39a2a50b35db088c..68f2e46d98ad3ba0b159895c72707598490d7538 100644
--- a/arch/arm/mach-lpc32xx/common.h
+++ b/arch/arm/mach-lpc32xx/common.h
@@ -29,6 +29,7 @@ extern struct platform_device lpc32xx_i2c0_device;
extern struct platform_device lpc32xx_i2c1_device;
extern struct platform_device lpc32xx_i2c2_device;
extern struct platform_device lpc32xx_tsc_device;
+extern struct platform_device lpc32xx_adc_device;
extern struct platform_device lpc32xx_rtc_device;
/*
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
index 8571d6250dc174cbc6f910b9c9eaed659e974910..0d79a3f8a5e0cae5d15e765ffb9bc799b192a2b4 100644
--- a/arch/arm/mach-lpc32xx/phy3250.c
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -254,6 +254,7 @@ static struct platform_device *phy3250_devs[] __initdata = {
&lpc32xx_i2c2_device,
&lpc32xx_watchdog_device,
&lpc32xx_gpio_led_device,
+ &lpc32xx_adc_device,
};
static struct amba_device *amba_devs[] __initdata = {
diff --git a/arch/arm/mach-mmp/include/mach/pxa910.h b/arch/arm/mach-mmp/include/mach/pxa910.h
index 4de13abef7bbf5a6413ca8fec3f647aee96a209e..e2e1f1e5e1249f908f7a8b531862d921abb00359 100644
--- a/arch/arm/mach-mmp/include/mach/pxa910.h
+++ b/arch/arm/mach-mmp/include/mach/pxa910.h
@@ -22,6 +22,7 @@ extern struct pxa_device_desc pxa910_device_pwm4;
extern struct pxa_device_desc pxa910_device_nand;
extern struct platform_device pxa910_device_gpio;
+extern struct platform_device pxa910_device_rtc;
static inline int pxa910_add_uart(int id)
{
diff --git a/arch/arm/mach-mmp/include/mach/regs-apbc.h b/arch/arm/mach-mmp/include/mach/regs-apbc.h
index 1a96585336ba12da9583e9ce10c9a6160fb932d2..8a37fb003655846a8491ca1b1aef5d851c1c0d26 100644
--- a/arch/arm/mach-mmp/include/mach/regs-apbc.h
+++ b/arch/arm/mach-mmp/include/mach/regs-apbc.h
@@ -57,6 +57,7 @@
#define APBC_PXA910_SSP1 APBC_REG(0x01c)
#define APBC_PXA910_SSP2 APBC_REG(0x020)
#define APBC_PXA910_IPC APBC_REG(0x024)
+#define APBC_PXA910_RTC APBC_REG(0x028)
#define APBC_PXA910_TWSI0 APBC_REG(0x02c)
#define APBC_PXA910_KPC APBC_REG(0x030)
#define APBC_PXA910_TIMERS APBC_REG(0x034)
diff --git a/arch/arm/mach-mmp/include/mach/regs-rtc.h b/arch/arm/mach-mmp/include/mach/regs-rtc.h
new file mode 100644
index 0000000000000000000000000000000000000000..5bff886a394127b7b4afbad628412c907d015551
--- /dev/null
+++ b/arch/arm/mach-mmp/include/mach/regs-rtc.h
@@ -0,0 +1,23 @@
+#ifndef __ASM_MACH_REGS_RTC_H
+#define __ASM_MACH_REGS_RTC_H
+
+#include <mach/addr-map.h>
+
+#define RTC_VIRT_BASE (APB_VIRT_BASE + 0x10000)
+#define RTC_REG(x) (*((volatile u32 __iomem *)(RTC_VIRT_BASE + (x))))
+
+/*
+ * Real Time Clock
+ */
+
+#define RCNR RTC_REG(0x00) /* RTC Count Register */
+#define RTAR RTC_REG(0x04) /* RTC Alarm Register */
+#define RTSR RTC_REG(0x08) /* RTC Status Register */
+#define RTTR RTC_REG(0x0C) /* RTC Timer Trim Register */
+
+#define RTSR_HZE (1 << 3) /* HZ interrupt enable */
+#define RTSR_ALE (1 << 2) /* RTC alarm interrupt enable */
+#define RTSR_HZ (1 << 1) /* HZ rising-edge detected */
+#define RTSR_AL (1 << 0) /* RTC alarm detected */
+
+#endif /* __ASM_MACH_REGS_RTC_H */
diff --git a/arch/arm/mach-mmp/pxa910.c b/arch/arm/mach-mmp/pxa910.c
index 0c87e69adf9fa6da1a9df2b10cc6dda8a1d132ea..43f8bcc29b67734a733260381f256db6b1ce19e7 100644
--- a/arch/arm/mach-mmp/pxa910.c
+++ b/arch/arm/mach-mmp/pxa910.c
@@ -92,6 +92,7 @@ static APBC_CLK(pwm2, PXA910_PWM2, 1, 13000000);
static APBC_CLK(pwm3, PXA910_PWM3, 1, 13000000);
static APBC_CLK(pwm4, PXA910_PWM4, 1, 13000000);
static APBC_CLK(gpio, PXA910_GPIO, 0, 13000000);
+static APBC_CLK(rtc, PXA910_RTC, 8, 32768);
static APMU_CLK(nand, NAND, 0x19b, 156000000);
static APMU_CLK(u2o, USB, 0x1b, 480000000);
@@ -109,6 +110,7 @@ static struct clk_lookup pxa910_clkregs[] = {
INIT_CLKREG(&clk_nand, "pxa3xx-nand", NULL),
INIT_CLKREG(&clk_gpio, "pxa-gpio", NULL),
INIT_CLKREG(&clk_u2o, "pxa-u2o", "U2OCLK"),
+ INIT_CLKREG(&clk_rtc, "sa1100-rtc", NULL),
};
static int __init pxa910_init(void)
@@ -184,3 +186,28 @@ struct platform_device pxa910_device_gpio = {
.num_resources = ARRAY_SIZE(pxa910_resource_gpio),
.resource = pxa910_resource_gpio,
};
+
+static struct resource pxa910_resource_rtc[] = {
+ {
+ .start = 0xd4010000,
+ .end = 0xd401003f,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_PXA910_RTC_INT,
+ .end = IRQ_PXA910_RTC_INT,
+ .name = "rtc 1Hz",
+ .flags = IORESOURCE_IRQ,
+ }, {
+ .start = IRQ_PXA910_RTC_ALARM,
+ .end = IRQ_PXA910_RTC_ALARM,
+ .name = "rtc alarm",
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device pxa910_device_rtc = {
+ .name = "sa1100-rtc",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(pxa910_resource_rtc),
+ .resource = pxa910_resource_rtc,
+};
diff --git a/arch/arm/mach-mmp/ttc_dkb.c b/arch/arm/mach-mmp/ttc_dkb.c
index 5ac5d5832e450b7b4a6db27941c5eabd8a3f7816..e72c709da44f3e2461e6817c504ed571b909fecd 100644
--- a/arch/arm/mach-mmp/ttc_dkb.c
+++ b/arch/arm/mach-mmp/ttc_dkb.c
@@ -124,6 +124,7 @@ static struct platform_device ttc_dkb_device_onenand = {
static struct platform_device *ttc_dkb_devices[] = {
&pxa910_device_gpio,
+ &pxa910_device_rtc,
&ttc_dkb_device_onenand,
};
diff --git a/arch/arm/mach-mxs/clock-mx23.c b/arch/arm/mach-mxs/clock-mx23.c
index 293958beb5057119a649e1485419b55e51181159..e3ac52c3401971678e8150ba1cea532218b75c8c 100644
--- a/arch/arm/mach-mxs/clock-mx23.c
+++ b/arch/arm/mach-mxs/clock-mx23.c
@@ -439,6 +439,7 @@ static struct clk_lookup lookups[] = {
_REGISTER_CLOCK("mxs-pwm.3", NULL, pwm_clk)
_REGISTER_CLOCK("mxs-pwm.4", NULL, pwm_clk)
_REGISTER_CLOCK("imx23-fb", NULL, lcdif_clk)
+ _REGISTER_CLOCK("imx23-gpmi-nand", NULL, gpmi_clk)
};
static int clk_misc_init(void)
diff --git a/arch/arm/mach-mxs/clock-mx28.c b/arch/arm/mach-mxs/clock-mx28.c
index 22ad12f6e4dee33357c5d7412af0d6f2896e9750..cea29c99e2143c05d8ce878a9226604d16b346a8 100644
--- a/arch/arm/mach-mxs/clock-mx28.c
+++ b/arch/arm/mach-mxs/clock-mx28.c
@@ -617,6 +617,7 @@ static struct clk_lookup lookups[] = {
_REGISTER_CLOCK("duart", NULL, uart_clk)
_REGISTER_CLOCK("imx28-fec.0", NULL, fec_clk)
_REGISTER_CLOCK("imx28-fec.1", NULL, fec_clk)
+ _REGISTER_CLOCK("imx28-gpmi-nand", NULL, gpmi_clk)
_REGISTER_CLOCK("mxs-auart.0", NULL, uart_clk)
_REGISTER_CLOCK("mxs-auart.1", NULL, uart_clk)
_REGISTER_CLOCK("mxs-auart.2", NULL, uart_clk)
diff --git a/arch/arm/mach-mxs/devices-mx23.h b/arch/arm/mach-mxs/devices-mx23.h
index 3fa651d2c994064df280a11109716b9f0b8e4282..4d1329d59287f543a845f453aac239c0bfc1875a 100644
--- a/arch/arm/mach-mxs/devices-mx23.h
+++ b/arch/arm/mach-mxs/devices-mx23.h
@@ -21,6 +21,10 @@ extern const struct mxs_auart_data mx23_auart_data[] __initconst;
#define mx23_add_auart0() mx23_add_auart(0)
#define mx23_add_auart1() mx23_add_auart(1)
+extern const struct mxs_gpmi_nand_data mx23_gpmi_nand_data __initconst;
+#define mx23_add_gpmi_nand(pdata) \
+ mxs_add_gpmi_nand(pdata, &mx23_gpmi_nand_data)
+
extern const struct mxs_mxs_mmc_data mx23_mxs_mmc_data[] __initconst;
#define mx23_add_mxs_mmc(id, pdata) \
mxs_add_mxs_mmc(&mx23_mxs_mmc_data[id], pdata)
diff --git a/arch/arm/mach-mxs/devices-mx28.h b/arch/arm/mach-mxs/devices-mx28.h
index 4f50094e293d35aa9cd28e980ae647e63c0beb8c..9dbeae130842b626522466764241b85cea105a75 100644
--- a/arch/arm/mach-mxs/devices-mx28.h
+++ b/arch/arm/mach-mxs/devices-mx28.h
@@ -34,6 +34,10 @@ extern const struct mxs_flexcan_data mx28_flexcan_data[] __initconst;
#define mx28_add_flexcan0(pdata) mx28_add_flexcan(0, pdata)
#define mx28_add_flexcan1(pdata) mx28_add_flexcan(1, pdata)
+extern const struct mxs_gpmi_nand_data mx28_gpmi_nand_data __initconst;
+#define mx28_add_gpmi_nand(pdata) \
+ mxs_add_gpmi_nand(pdata, &mx28_gpmi_nand_data)
+
extern const struct mxs_mxs_i2c_data mx28_mxs_i2c_data[] __initconst;
#define mx28_add_mxs_i2c(id) mxs_add_mxs_i2c(&mx28_mxs_i2c_data[id])
diff --git a/arch/arm/mach-mxs/devices/Kconfig b/arch/arm/mach-mxs/devices/Kconfig
index 18b6bf526a272242b1a0d03a78ee4b64b4209f7a..b8913df4cfa209402affd945457517f1b1ef8677 100644
--- a/arch/arm/mach-mxs/devices/Kconfig
+++ b/arch/arm/mach-mxs/devices/Kconfig
@@ -12,6 +12,9 @@ config MXS_HAVE_PLATFORM_FLEXCAN
select HAVE_CAN_FLEXCAN if CAN
bool
+config MXS_HAVE_PLATFORM_GPMI_NAND
+ bool
+
config MXS_HAVE_PLATFORM_MXS_I2C
bool
diff --git a/arch/arm/mach-mxs/devices/Makefile b/arch/arm/mach-mxs/devices/Makefile
index f52e3e53baecea42559efed2051e3ca6270cf944..c8f5c9541a302461ee56dcaf0d8bdff83445a38d 100644
--- a/arch/arm/mach-mxs/devices/Makefile
+++ b/arch/arm/mach-mxs/devices/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_MXS_HAVE_PLATFORM_AUART) += platform-auart.o
obj-y += platform-dma.o
obj-$(CONFIG_MXS_HAVE_PLATFORM_FEC) += platform-fec.o
obj-$(CONFIG_MXS_HAVE_PLATFORM_FLEXCAN) += platform-flexcan.o
+obj-$(CONFIG_MXS_HAVE_PLATFORM_GPMI_NAND) += platform-gpmi-nand.o
obj-$(CONFIG_MXS_HAVE_PLATFORM_MXS_I2C) += platform-mxs-i2c.o
obj-$(CONFIG_MXS_HAVE_PLATFORM_MXS_MMC) += platform-mxs-mmc.o
obj-$(CONFIG_MXS_HAVE_PLATFORM_MXS_PWM) += platform-mxs-pwm.o
diff --git a/arch/arm/mach-mxs/devices/platform-gpmi-nand.c b/arch/arm/mach-mxs/devices/platform-gpmi-nand.c
new file mode 100644
index 0000000000000000000000000000000000000000..3e22df5944a8bab0154fdfe906fecc3db29d391b
--- /dev/null
+++ b/arch/arm/mach-mxs/devices/platform-gpmi-nand.c
@@ -0,0 +1,81 @@
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+#include <asm/sizes.h>
+#include <mach/mx23.h>
+#include <mach/mx28.h>
+#include <mach/devices-common.h>
+#include <linux/dma-mapping.h>
+
+#ifdef CONFIG_SOC_IMX23
+const struct mxs_gpmi_nand_data mx23_gpmi_nand_data __initconst = {
+ .devid = "imx23-gpmi-nand",
+ .res = {
+ /* GPMI */
+ DEFINE_RES_MEM_NAMED(MX23_GPMI_BASE_ADDR, SZ_8K,
+ GPMI_NAND_GPMI_REGS_ADDR_RES_NAME),
+ DEFINE_RES_IRQ_NAMED(MX23_INT_GPMI_ATTENTION,
+ GPMI_NAND_GPMI_INTERRUPT_RES_NAME),
+ /* BCH */
+ DEFINE_RES_MEM_NAMED(MX23_BCH_BASE_ADDR, SZ_8K,
+ GPMI_NAND_BCH_REGS_ADDR_RES_NAME),
+ DEFINE_RES_IRQ_NAMED(MX23_INT_BCH,
+ GPMI_NAND_BCH_INTERRUPT_RES_NAME),
+ /* DMA */
+ DEFINE_RES_NAMED(MX23_DMA_GPMI0,
+ MX23_DMA_GPMI3 - MX23_DMA_GPMI0 + 1,
+ GPMI_NAND_DMA_CHANNELS_RES_NAME,
+ IORESOURCE_DMA),
+ DEFINE_RES_IRQ_NAMED(MX23_INT_GPMI_DMA,
+ GPMI_NAND_DMA_INTERRUPT_RES_NAME),
+ },
+};
+#endif
+
+#ifdef CONFIG_SOC_IMX28
+const struct mxs_gpmi_nand_data mx28_gpmi_nand_data __initconst = {
+ .devid = "imx28-gpmi-nand",
+ .res = {
+ /* GPMI */
+ DEFINE_RES_MEM_NAMED(MX28_GPMI_BASE_ADDR, SZ_8K,
+ GPMI_NAND_GPMI_REGS_ADDR_RES_NAME),
+ DEFINE_RES_IRQ_NAMED(MX28_INT_GPMI,
+ GPMI_NAND_GPMI_INTERRUPT_RES_NAME),
+ /* BCH */
+ DEFINE_RES_MEM_NAMED(MX28_BCH_BASE_ADDR, SZ_8K,
+ GPMI_NAND_BCH_REGS_ADDR_RES_NAME),
+ DEFINE_RES_IRQ_NAMED(MX28_INT_BCH,
+ GPMI_NAND_BCH_INTERRUPT_RES_NAME),
+ /* DMA */
+ DEFINE_RES_NAMED(MX28_DMA_GPMI0,
+ MX28_DMA_GPMI7 - MX28_DMA_GPMI0 + 1,
+ GPMI_NAND_DMA_CHANNELS_RES_NAME,
+ IORESOURCE_DMA),
+ DEFINE_RES_IRQ_NAMED(MX28_INT_GPMI_DMA,
+ GPMI_NAND_DMA_INTERRUPT_RES_NAME),
+ },
+};
+#endif
+
+struct platform_device *__init
+mxs_add_gpmi_nand(const struct gpmi_nand_platform_data *pdata,
+ const struct mxs_gpmi_nand_data *data)
+{
+ return mxs_add_platform_device_dmamask(data->devid, -1,
+ data->res, GPMI_NAND_RES_SIZE,
+ pdata, sizeof(*pdata), DMA_BIT_MASK(32));
+}
diff --git a/arch/arm/mach-mxs/include/mach/devices-common.h b/arch/arm/mach-mxs/include/mach/devices-common.h
index dc369c1239fc3eac5a1c7d27968a3bf5c27f3912..f2e383955d88576b66ecb55962f9956908b11759 100644
--- a/arch/arm/mach-mxs/include/mach/devices-common.h
+++ b/arch/arm/mach-mxs/include/mach/devices-common.h
@@ -66,6 +66,16 @@ struct platform_device *__init mxs_add_flexcan(
const struct mxs_flexcan_data *data,
const struct flexcan_platform_data *pdata);
+/* gpmi-nand */
+#include <linux/mtd/gpmi-nand.h>
+struct mxs_gpmi_nand_data {
+ const char *devid;
+ const struct resource res[GPMI_NAND_RES_SIZE];
+};
+struct platform_device *__init
+mxs_add_gpmi_nand(const struct gpmi_nand_platform_data *pdata,
+ const struct mxs_gpmi_nand_data *data);
+
/* i2c */
struct mxs_mxs_i2c_data {
int id;
diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
index 3c8dd928628efd7c01cad5a1d2743c7ddc34a660..34b9766d1d231845356b2c71626fa234a731bee6 100644
--- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
@@ -29,6 +29,7 @@
#include "omap_hwmod_common_data.h"
+#include "smartreflex.h"
#include "prm-regbits-34xx.h"
#include "cm-regbits-34xx.h"
#include "wd_timer.h"
@@ -376,6 +377,16 @@ static struct omap_hwmod_ocp_if omap3_l4_core__i2c3 = {
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
+static struct omap_hwmod_irq_info omap3_smartreflex_mpu_irqs[] = {
+ { .irq = 18},
+ { .irq = -1 }
+};
+
+static struct omap_hwmod_irq_info omap3_smartreflex_core_irqs[] = {
+ { .irq = 19},
+ { .irq = -1 }
+};
+
/* L4 CORE -> SR1 interface */
static struct omap_hwmod_addr_space omap3_sr1_addr_space[] = {
{
@@ -2664,6 +2675,10 @@ static struct omap_hwmod_class omap36xx_smartreflex_hwmod_class = {
};
/* SR1 */
+static struct omap_smartreflex_dev_attr sr1_dev_attr = {
+ .sensor_voltdm_name = "mpu_iva",
+};
+
static struct omap_hwmod_ocp_if *omap3_sr1_slaves[] = {
&omap3_l4_core__sr1,
};
@@ -2672,7 +2687,6 @@ static struct omap_hwmod omap34xx_sr1_hwmod = {
.name = "sr1_hwmod",
.class = &omap34xx_smartreflex_hwmod_class,
.main_clk = "sr1_fck",
- .vdd_name = "mpu_iva",
.prcm = {
.omap2 = {
.prcm_reg_id = 1,
@@ -2684,6 +2698,8 @@ static struct omap_hwmod omap34xx_sr1_hwmod = {
},
.slaves = omap3_sr1_slaves,
.slaves_cnt = ARRAY_SIZE(omap3_sr1_slaves),
+ .dev_attr = &sr1_dev_attr,
+ .mpu_irqs = omap3_smartreflex_mpu_irqs,
.flags = HWMOD_SET_DEFAULT_CLOCKACT,
};
@@ -2691,7 +2707,6 @@ static struct omap_hwmod omap36xx_sr1_hwmod = {
.name = "sr1_hwmod",
.class = &omap36xx_smartreflex_hwmod_class,
.main_clk = "sr1_fck",
- .vdd_name = "mpu_iva",
.prcm = {
.omap2 = {
.prcm_reg_id = 1,
@@ -2703,9 +2718,15 @@ static struct omap_hwmod omap36xx_sr1_hwmod = {
},
.slaves = omap3_sr1_slaves,
.slaves_cnt = ARRAY_SIZE(omap3_sr1_slaves),
+ .dev_attr = &sr1_dev_attr,
+ .mpu_irqs = omap3_smartreflex_mpu_irqs,
};
/* SR2 */
+static struct omap_smartreflex_dev_attr sr2_dev_attr = {
+ .sensor_voltdm_name = "core",
+};
+
static struct omap_hwmod_ocp_if *omap3_sr2_slaves[] = {
&omap3_l4_core__sr2,
};
@@ -2714,7 +2735,6 @@ static struct omap_hwmod omap34xx_sr2_hwmod = {
.name = "sr2_hwmod",
.class = &omap34xx_smartreflex_hwmod_class,
.main_clk = "sr2_fck",
- .vdd_name = "core",
.prcm = {
.omap2 = {
.prcm_reg_id = 1,
@@ -2726,6 +2746,8 @@ static struct omap_hwmod omap34xx_sr2_hwmod = {
},
.slaves = omap3_sr2_slaves,
.slaves_cnt = ARRAY_SIZE(omap3_sr2_slaves),
+ .dev_attr = &sr2_dev_attr,
+ .mpu_irqs = omap3_smartreflex_core_irqs,
.flags = HWMOD_SET_DEFAULT_CLOCKACT,
};
@@ -2733,7 +2755,6 @@ static struct omap_hwmod omap36xx_sr2_hwmod = {
.name = "sr2_hwmod",
.class = &omap36xx_smartreflex_hwmod_class,
.main_clk = "sr2_fck",
- .vdd_name = "core",
.prcm = {
.omap2 = {
.prcm_reg_id = 1,
@@ -2745,6 +2766,8 @@ static struct omap_hwmod omap36xx_sr2_hwmod = {
},
.slaves = omap3_sr2_slaves,
.slaves_cnt = ARRAY_SIZE(omap3_sr2_slaves),
+ .dev_attr = &sr2_dev_attr,
+ .mpu_irqs = omap3_smartreflex_core_irqs,
};
/*
diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
index acb561ea7c11f221ab6d418ea72f31c81ee7eadc..08daa5e0eb5fdbd1fa3a20c5c1ba4dd1112b3d90 100644
--- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
@@ -33,6 +33,7 @@
#include "omap_hwmod_common_data.h"
+#include "smartreflex.h"
#include "cm1_44xx.h"
#include "cm2_44xx.h"
#include "prm44xx.h"
@@ -3962,6 +3963,10 @@ static struct omap_hwmod_class omap44xx_smartreflex_hwmod_class = {
};
/* smartreflex_core */
+static struct omap_smartreflex_dev_attr smartreflex_core_dev_attr = {
+ .sensor_voltdm_name = "core",
+};
+
static struct omap_hwmod omap44xx_smartreflex_core_hwmod;
static struct omap_hwmod_irq_info omap44xx_smartreflex_core_irqs[] = {
{ .irq = 19 + OMAP44XX_IRQ_GIC_START },
@@ -3998,7 +4003,6 @@ static struct omap_hwmod omap44xx_smartreflex_core_hwmod = {
.mpu_irqs = omap44xx_smartreflex_core_irqs,
.main_clk = "smartreflex_core_fck",
- .vdd_name = "core",
.prcm = {
.omap4 = {
.clkctrl_offs = OMAP4_CM_ALWON_SR_CORE_CLKCTRL_OFFSET,
@@ -4008,9 +4012,14 @@ static struct omap_hwmod omap44xx_smartreflex_core_hwmod = {
},
.slaves = omap44xx_smartreflex_core_slaves,
.slaves_cnt = ARRAY_SIZE(omap44xx_smartreflex_core_slaves),
+ .dev_attr = &smartreflex_core_dev_attr,
};
/* smartreflex_iva */
+static struct omap_smartreflex_dev_attr smartreflex_iva_dev_attr = {
+ .sensor_voltdm_name = "iva",
+};
+
static struct omap_hwmod omap44xx_smartreflex_iva_hwmod;
static struct omap_hwmod_irq_info omap44xx_smartreflex_iva_irqs[] = {
{ .irq = 102 + OMAP44XX_IRQ_GIC_START },
@@ -4046,7 +4055,6 @@ static struct omap_hwmod omap44xx_smartreflex_iva_hwmod = {
.clkdm_name = "l4_ao_clkdm",
.mpu_irqs = omap44xx_smartreflex_iva_irqs,
.main_clk = "smartreflex_iva_fck",
- .vdd_name = "iva",
.prcm = {
.omap4 = {
.clkctrl_offs = OMAP4_CM_ALWON_SR_IVA_CLKCTRL_OFFSET,
@@ -4056,9 +4064,14 @@ static struct omap_hwmod omap44xx_smartreflex_iva_hwmod = {
},
.slaves = omap44xx_smartreflex_iva_slaves,
.slaves_cnt = ARRAY_SIZE(omap44xx_smartreflex_iva_slaves),
+ .dev_attr = &smartreflex_iva_dev_attr,
};
/* smartreflex_mpu */
+static struct omap_smartreflex_dev_attr smartreflex_mpu_dev_attr = {
+ .sensor_voltdm_name = "mpu",
+};
+
static struct omap_hwmod omap44xx_smartreflex_mpu_hwmod;
static struct omap_hwmod_irq_info omap44xx_smartreflex_mpu_irqs[] = {
{ .irq = 18 + OMAP44XX_IRQ_GIC_START },
@@ -4094,7 +4107,6 @@ static struct omap_hwmod omap44xx_smartreflex_mpu_hwmod = {
.clkdm_name = "l4_ao_clkdm",
.mpu_irqs = omap44xx_smartreflex_mpu_irqs,
.main_clk = "smartreflex_mpu_fck",
- .vdd_name = "mpu",
.prcm = {
.omap4 = {
.clkctrl_offs = OMAP4_CM_ALWON_SR_MPU_CLKCTRL_OFFSET,
@@ -4104,6 +4116,7 @@ static struct omap_hwmod omap44xx_smartreflex_mpu_hwmod = {
},
.slaves = omap44xx_smartreflex_mpu_slaves,
.slaves_cnt = ARRAY_SIZE(omap44xx_smartreflex_mpu_slaves),
+ .dev_attr = &smartreflex_mpu_dev_attr,
};
/*
diff --git a/arch/arm/mach-omap2/smartreflex-class3.c b/arch/arm/mach-omap2/smartreflex-class3.c
index 53d9d0a5b39d1a66fcb797161a3b24c0beeaf1f4..955566eefac4ac515516957e3f6d65cbc3353c35 100644
--- a/arch/arm/mach-omap2/smartreflex-class3.c
+++ b/arch/arm/mach-omap2/smartreflex-class3.c
@@ -29,6 +29,7 @@ static int sr_class3_enable(struct voltagedomain *voltdm)
static int sr_class3_disable(struct voltagedomain *voltdm, int is_volt_reset)
{
+ sr_disable_errgen(voltdm);
omap_vp_disable(voltdm);
sr_disable(voltdm);
if (is_volt_reset)
diff --git a/arch/arm/mach-omap2/smartreflex.c b/arch/arm/mach-omap2/smartreflex.c
index 47c77a1d932a281d98847cbd5eb92575f49a16c7..008fbd7b9352271d46b385a303dfb53112489655 100644
--- a/arch/arm/mach-omap2/smartreflex.c
+++ b/arch/arm/mach-omap2/smartreflex.c
@@ -36,6 +36,12 @@
#define SR_DISABLE_TIMEOUT 200
struct omap_sr {
+ struct list_head node;
+ struct platform_device *pdev;
+ struct omap_sr_nvalue_table *nvalue_table;
+ struct voltagedomain *voltdm;
+ struct dentry *dbg_dir;
+ unsigned int irq;
int srid;
int ip_type;
int nvalue_count;
@@ -49,13 +55,7 @@ struct omap_sr {
u32 senp_avgweight;
u32 senp_mod;
u32 senn_mod;
- unsigned int irq;
void __iomem *base;
- struct platform_device *pdev;
- struct list_head node;
- struct omap_sr_nvalue_table *nvalue_table;
- struct voltagedomain *voltdm;
- struct dentry *dbg_dir;
};
/* sr_list contains all the instances of smartreflex module */
@@ -74,10 +74,6 @@ static inline void sr_modify_reg(struct omap_sr *sr, unsigned offset, u32 mask,
u32 value)
{
u32 reg_val;
- u32 errconfig_offs = 0, errconfig_mask = 0;
-
- reg_val = __raw_readl(sr->base + offset);
- reg_val &= ~mask;
/*
* Smartreflex error config register is special as it contains
@@ -88,16 +84,15 @@ static inline void sr_modify_reg(struct omap_sr *sr, unsigned offset, u32 mask,
* if they are currently set, but does allow the caller to write
* those bits.
*/
- if (sr->ip_type == SR_TYPE_V1) {
- errconfig_offs = ERRCONFIG_V1;
- errconfig_mask = ERRCONFIG_STATUS_V1_MASK;
- } else if (sr->ip_type == SR_TYPE_V2) {
- errconfig_offs = ERRCONFIG_V2;
- errconfig_mask = ERRCONFIG_VPBOUNDINTST_V2;
- }
+ if (sr->ip_type == SR_TYPE_V1 && offset == ERRCONFIG_V1)
+ mask |= ERRCONFIG_STATUS_V1_MASK;
+ else if (sr->ip_type == SR_TYPE_V2 && offset == ERRCONFIG_V2)
+ mask |= ERRCONFIG_VPBOUNDINTST_V2;
+
+ reg_val = __raw_readl(sr->base + offset);
+ reg_val &= ~mask;
- if (offset == errconfig_offs)
- reg_val &= ~errconfig_mask;
+ value &= mask;
reg_val |= value;
@@ -128,21 +123,28 @@ static struct omap_sr *_sr_lookup(struct voltagedomain *voltdm)
static irqreturn_t sr_interrupt(int irq, void *data)
{
- struct omap_sr *sr_info = (struct omap_sr *)data;
+ struct omap_sr *sr_info = data;
u32 status = 0;
- if (sr_info->ip_type == SR_TYPE_V1) {
+ switch (sr_info->ip_type) {
+ case SR_TYPE_V1:
/* Read the status bits */
status = sr_read_reg(sr_info, ERRCONFIG_V1);
/* Clear them by writing back */
sr_write_reg(sr_info, ERRCONFIG_V1, status);
- } else if (sr_info->ip_type == SR_TYPE_V2) {
+ break;
+ case SR_TYPE_V2:
/* Read the status bits */
status = sr_read_reg(sr_info, IRQSTATUS);
/* Clear them by writing back */
sr_write_reg(sr_info, IRQSTATUS, status);
+ break;
+ default:
+ dev_err(&sr_info->pdev->dev, "UNKNOWN IP type %d\n",
+ sr_info->ip_type);
+ return IRQ_NONE;
}
if (sr_class->notify)
@@ -166,6 +168,7 @@ static void sr_set_clk_length(struct omap_sr *sr)
__func__);
return;
}
+
sys_clk_speed = clk_get_rate(sys_ck);
clk_put(sys_ck);
@@ -267,7 +270,7 @@ static int sr_late_init(struct omap_sr *sr_info)
goto error;
}
ret = request_irq(sr_info->irq, sr_interrupt,
- 0, name, (void *)sr_info);
+ 0, name, sr_info);
if (ret)
goto error;
disable_irq(sr_info->irq);
@@ -288,12 +291,15 @@ static int sr_late_init(struct omap_sr *sr_info)
"not function as desired\n", __func__);
kfree(name);
kfree(sr_info);
+
return ret;
}
static void sr_v1_disable(struct omap_sr *sr)
{
int timeout = 0;
+ int errconf_val = ERRCONFIG_MCUACCUMINTST | ERRCONFIG_MCUVALIDINTST |
+ ERRCONFIG_MCUBOUNDINTST;
/* Enable MCUDisableAcknowledge interrupt */
sr_modify_reg(sr, ERRCONFIG_V1,
@@ -302,13 +308,13 @@ static void sr_v1_disable(struct omap_sr *sr)
/* SRCONFIG - disable SR */
sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0x0);
- /* Disable all other SR interrupts and clear the status */
+ /* Disable all other SR interrupts and clear the status as needed */
+ if (sr_read_reg(sr, ERRCONFIG_V1) & ERRCONFIG_VPBOUNDINTST_V1)
+ errconf_val |= ERRCONFIG_VPBOUNDINTST_V1;
sr_modify_reg(sr, ERRCONFIG_V1,
(ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUVALIDINTEN |
ERRCONFIG_MCUBOUNDINTEN | ERRCONFIG_VPBOUNDINTEN_V1),
- (ERRCONFIG_MCUACCUMINTST | ERRCONFIG_MCUVALIDINTST |
- ERRCONFIG_MCUBOUNDINTST |
- ERRCONFIG_VPBOUNDINTST_V1));
+ errconf_val);
/*
* Wait for SR to be disabled.
@@ -337,9 +343,17 @@ static void sr_v2_disable(struct omap_sr *sr)
/* SRCONFIG - disable SR */
sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0x0);
- /* Disable all other SR interrupts and clear the status */
- sr_modify_reg(sr, ERRCONFIG_V2, ERRCONFIG_VPBOUNDINTEN_V2,
+ /*
+ * Disable all other SR interrupts and clear the status
+ * write to status register ONLY on need basis - only if status
+ * is set.
+ */
+ if (sr_read_reg(sr, ERRCONFIG_V2) & ERRCONFIG_VPBOUNDINTST_V2)
+ sr_modify_reg(sr, ERRCONFIG_V2, ERRCONFIG_VPBOUNDINTEN_V2,
ERRCONFIG_VPBOUNDINTST_V2);
+ else
+ sr_modify_reg(sr, ERRCONFIG_V2, ERRCONFIG_VPBOUNDINTEN_V2,
+ 0x0);
sr_write_reg(sr, IRQENABLE_CLR, (IRQENABLE_MCUACCUMINT |
IRQENABLE_MCUVALIDINT |
IRQENABLE_MCUBOUNDSINT));
@@ -398,15 +412,16 @@ static u32 sr_retrieve_nvalue(struct omap_sr *sr, u32 efuse_offs)
*/
int sr_configure_errgen(struct voltagedomain *voltdm)
{
- u32 sr_config, sr_errconfig, errconfig_offs, vpboundint_en;
- u32 vpboundint_st, senp_en = 0, senn_en = 0;
+ u32 sr_config, sr_errconfig, errconfig_offs;
+ u32 vpboundint_en, vpboundint_st;
+ u32 senp_en = 0, senn_en = 0;
u8 senp_shift, senn_shift;
struct omap_sr *sr = _sr_lookup(voltdm);
if (IS_ERR(sr)) {
pr_warning("%s: omap_sr struct for sr_%s not found\n",
__func__, voltdm->name);
- return -EINVAL;
+ return PTR_ERR(sr);
}
if (!sr->clk_length)
@@ -418,20 +433,23 @@ int sr_configure_errgen(struct voltagedomain *voltdm)
sr_config = (sr->clk_length << SRCONFIG_SRCLKLENGTH_SHIFT) |
SRCONFIG_SENENABLE | SRCONFIG_ERRGEN_EN;
- if (sr->ip_type == SR_TYPE_V1) {
+ switch (sr->ip_type) {
+ case SR_TYPE_V1:
sr_config |= SRCONFIG_DELAYCTRL;
senn_shift = SRCONFIG_SENNENABLE_V1_SHIFT;
senp_shift = SRCONFIG_SENPENABLE_V1_SHIFT;
errconfig_offs = ERRCONFIG_V1;
vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V1;
vpboundint_st = ERRCONFIG_VPBOUNDINTST_V1;
- } else if (sr->ip_type == SR_TYPE_V2) {
+ break;
+ case SR_TYPE_V2:
senn_shift = SRCONFIG_SENNENABLE_V2_SHIFT;
senp_shift = SRCONFIG_SENPENABLE_V2_SHIFT;
errconfig_offs = ERRCONFIG_V2;
vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V2;
vpboundint_st = ERRCONFIG_VPBOUNDINTST_V2;
- } else {
+ break;
+ default:
dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
"module without specifying the ip\n", __func__);
return -EINVAL;
@@ -447,8 +465,55 @@ int sr_configure_errgen(struct voltagedomain *voltdm)
sr_errconfig);
/* Enabling the interrupts if the ERROR module is used */
- sr_modify_reg(sr, errconfig_offs,
- vpboundint_en, (vpboundint_en | vpboundint_st));
+ sr_modify_reg(sr, errconfig_offs, (vpboundint_en | vpboundint_st),
+ vpboundint_en);
+
+ return 0;
+}
+
+/**
+ * sr_disable_errgen() - Disables SmartReflex AVS module's errgen component
+ * @voltdm: VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the smartreflex class driver to
+ * disable the error generator module inside the smartreflex module.
+ *
+ * Returns 0 on success and error value in case of failure.
+ */
+int sr_disable_errgen(struct voltagedomain *voltdm)
+{
+ u32 errconfig_offs;
+ u32 vpboundint_en, vpboundint_st;
+ struct omap_sr *sr = _sr_lookup(voltdm);
+
+ if (IS_ERR(sr)) {
+ pr_warning("%s: omap_sr struct for sr_%s not found\n",
+ __func__, voltdm->name);
+ return PTR_ERR(sr);
+ }
+
+ switch (sr->ip_type) {
+ case SR_TYPE_V1:
+ errconfig_offs = ERRCONFIG_V1;
+ vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V1;
+ vpboundint_st = ERRCONFIG_VPBOUNDINTST_V1;
+ break;
+ case SR_TYPE_V2:
+ errconfig_offs = ERRCONFIG_V2;
+ vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V2;
+ vpboundint_st = ERRCONFIG_VPBOUNDINTST_V2;
+ break;
+ default:
+ dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
+ "module without specifying the ip\n", __func__);
+ return -EINVAL;
+ }
+
+ /* Disable the interrupts of ERROR module */
+ sr_modify_reg(sr, errconfig_offs, vpboundint_en | vpboundint_st, 0);
+
+ /* Disable the Sensor and errorgen */
+ sr_modify_reg(sr, SRCONFIG, SRCONFIG_SENENABLE | SRCONFIG_ERRGEN_EN, 0);
return 0;
}
@@ -475,7 +540,7 @@ int sr_configure_minmax(struct voltagedomain *voltdm)
if (IS_ERR(sr)) {
pr_warning("%s: omap_sr struct for sr_%s not found\n",
__func__, voltdm->name);
- return -EINVAL;
+ return PTR_ERR(sr);
}
if (!sr->clk_length)
@@ -488,14 +553,17 @@ int sr_configure_minmax(struct voltagedomain *voltdm)
SRCONFIG_SENENABLE |
(sr->accum_data << SRCONFIG_ACCUMDATA_SHIFT);
- if (sr->ip_type == SR_TYPE_V1) {
+ switch (sr->ip_type) {
+ case SR_TYPE_V1:
sr_config |= SRCONFIG_DELAYCTRL;
senn_shift = SRCONFIG_SENNENABLE_V1_SHIFT;
senp_shift = SRCONFIG_SENPENABLE_V1_SHIFT;
- } else if (sr->ip_type == SR_TYPE_V2) {
+ break;
+ case SR_TYPE_V2:
senn_shift = SRCONFIG_SENNENABLE_V2_SHIFT;
senp_shift = SRCONFIG_SENPENABLE_V2_SHIFT;
- } else {
+ break;
+ default:
dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
"module without specifying the ip\n", __func__);
return -EINVAL;
@@ -511,20 +579,27 @@ int sr_configure_minmax(struct voltagedomain *voltdm)
* Enabling the interrupts if MINMAXAVG module is used.
* TODO: check if all the interrupts are mandatory
*/
- if (sr->ip_type == SR_TYPE_V1) {
+ switch (sr->ip_type) {
+ case SR_TYPE_V1:
sr_modify_reg(sr, ERRCONFIG_V1,
(ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUVALIDINTEN |
ERRCONFIG_MCUBOUNDINTEN),
(ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUACCUMINTST |
ERRCONFIG_MCUVALIDINTEN | ERRCONFIG_MCUVALIDINTST |
ERRCONFIG_MCUBOUNDINTEN | ERRCONFIG_MCUBOUNDINTST));
- } else if (sr->ip_type == SR_TYPE_V2) {
+ break;
+ case SR_TYPE_V2:
sr_write_reg(sr, IRQSTATUS,
IRQSTATUS_MCUACCUMINT | IRQSTATUS_MCVALIDINT |
IRQSTATUS_MCBOUNDSINT | IRQSTATUS_MCUDISABLEACKINT);
sr_write_reg(sr, IRQENABLE_SET,
IRQENABLE_MCUACCUMINT | IRQENABLE_MCUVALIDINT |
IRQENABLE_MCUBOUNDSINT | IRQENABLE_MCUDISABLEACKINT);
+ break;
+ default:
+ dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
+ "module without specifying the ip\n", __func__);
+ return -EINVAL;
}
return 0;
@@ -543,15 +618,15 @@ int sr_configure_minmax(struct voltagedomain *voltdm)
*/
int sr_enable(struct voltagedomain *voltdm, unsigned long volt)
{
- u32 nvalue_reciprocal;
struct omap_volt_data *volt_data;
struct omap_sr *sr = _sr_lookup(voltdm);
+ u32 nvalue_reciprocal;
int ret;
if (IS_ERR(sr)) {
pr_warning("%s: omap_sr struct for sr_%s not found\n",
__func__, voltdm->name);
- return -EINVAL;
+ return PTR_ERR(sr);
}
volt_data = omap_voltage_get_voltdata(sr->voltdm, volt);
@@ -559,7 +634,7 @@ int sr_enable(struct voltagedomain *voltdm, unsigned long volt)
if (IS_ERR(volt_data)) {
dev_warn(&sr->pdev->dev, "%s: Unable to get voltage table"
"for nominal voltage %ld\n", __func__, volt);
- return -ENODATA;
+ return PTR_ERR(volt_data);
}
nvalue_reciprocal = sr_retrieve_nvalue(sr, volt_data->sr_efuse_offs);
@@ -617,10 +692,17 @@ void sr_disable(struct voltagedomain *voltdm)
* disable the clocks.
*/
if (sr_read_reg(sr, SRCONFIG) & SRCONFIG_SRENABLE) {
- if (sr->ip_type == SR_TYPE_V1)
+ switch (sr->ip_type) {
+ case SR_TYPE_V1:
sr_v1_disable(sr);
- else if (sr->ip_type == SR_TYPE_V2)
+ break;
+ case SR_TYPE_V2:
sr_v2_disable(sr);
+ break;
+ default:
+ dev_err(&sr->pdev->dev, "UNKNOWN IP type %d\n",
+ sr->ip_type);
+ }
}
pm_runtime_put_sync_suspend(&sr->pdev->dev);
@@ -779,10 +861,10 @@ void omap_sr_register_pmic(struct omap_sr_pmic_data *pmic_data)
sr_pmic_data = pmic_data;
}
-/* PM Debug Fs enteries to enable disable smartreflex. */
+/* PM Debug FS entries to enable and disable smartreflex. */
static int omap_sr_autocomp_show(void *data, u64 *val)
{
- struct omap_sr *sr_info = (struct omap_sr *) data;
+ struct omap_sr *sr_info = data;
if (!sr_info) {
pr_warning("%s: omap_sr struct not found\n", __func__);
@@ -796,7 +878,7 @@ static int omap_sr_autocomp_show(void *data, u64 *val)
static int omap_sr_autocomp_store(void *data, u64 val)
{
- struct omap_sr *sr_info = (struct omap_sr *) data;
+ struct omap_sr *sr_info = data;
if (!sr_info) {
pr_warning("%s: omap_sr struct not found\n", __func__);
@@ -804,7 +886,7 @@ static int omap_sr_autocomp_store(void *data, u64 val)
}
/* Sanity check */
- if (val && (val != 1)) {
+ if (val > 1) {
pr_warning("%s: Invalid argument %lld\n", __func__, val);
return -EINVAL;
}
@@ -821,11 +903,11 @@ static int omap_sr_autocomp_store(void *data, u64 val)
}
DEFINE_SIMPLE_ATTRIBUTE(pm_sr_fops, omap_sr_autocomp_show,
- omap_sr_autocomp_store, "%llu\n");
+ omap_sr_autocomp_store, "%llu\n");
static int __init omap_sr_probe(struct platform_device *pdev)
{
- struct omap_sr *sr_info = kzalloc(sizeof(struct omap_sr), GFP_KERNEL);
+ struct omap_sr *sr_info;
struct omap_sr_data *pdata = pdev->dev.platform_data;
struct resource *mem, *irq;
struct dentry *nvalue_dir;
@@ -833,12 +915,15 @@ static int __init omap_sr_probe(struct platform_device *pdev)
int i, ret = 0;
char *name;
+ sr_info = kzalloc(sizeof(struct omap_sr), GFP_KERNEL);
if (!sr_info) {
dev_err(&pdev->dev, "%s: unable to allocate sr_info\n",
__func__);
return -ENOMEM;
}
+ platform_set_drvdata(pdev, sr_info);
+
if (!pdata) {
dev_err(&pdev->dev, "%s: platform data missing\n", __func__);
ret = -EINVAL;
@@ -904,7 +989,7 @@ static int __init omap_sr_probe(struct platform_device *pdev)
dev_info(&pdev->dev, "%s: SmartReflex driver initialized\n", __func__);
if (!sr_dbg_dir) {
sr_dbg_dir = debugfs_create_dir("smartreflex", NULL);
- if (!sr_dbg_dir) {
+ if (IS_ERR_OR_NULL(sr_dbg_dir)) {
ret = PTR_ERR(sr_dbg_dir);
pr_err("%s:sr debugfs dir creation failed(%d)\n",
__func__, ret);
@@ -921,7 +1006,7 @@ static int __init omap_sr_probe(struct platform_device *pdev)
}
sr_info->dbg_dir = debugfs_create_dir(name, sr_dbg_dir);
kfree(name);
- if (IS_ERR(sr_info->dbg_dir)) {
+ if (IS_ERR_OR_NULL(sr_info->dbg_dir)) {
dev_err(&pdev->dev, "%s: Unable to create debugfs directory\n",
__func__);
ret = PTR_ERR(sr_info->dbg_dir);
@@ -938,7 +1023,7 @@ static int __init omap_sr_probe(struct platform_device *pdev)
&sr_info->err_minlimit);
nvalue_dir = debugfs_create_dir("nvalue", sr_info->dbg_dir);
- if (IS_ERR(nvalue_dir)) {
+ if (IS_ERR_OR_NULL(nvalue_dir)) {
dev_err(&pdev->dev, "%s: Unable to create debugfs directory"
"for n-values\n", __func__);
ret = PTR_ERR(nvalue_dir);
@@ -994,7 +1079,7 @@ static int __devexit omap_sr_remove(struct platform_device *pdev)
if (IS_ERR(sr_info)) {
dev_warn(&pdev->dev, "%s: omap_sr struct not found\n",
__func__);
- return -EINVAL;
+ return PTR_ERR(sr_info);
}
if (sr_info->autocomp_active)
@@ -1011,8 +1096,32 @@ static int __devexit omap_sr_remove(struct platform_device *pdev)
return 0;
}
+static void __devexit omap_sr_shutdown(struct platform_device *pdev)
+{
+ struct omap_sr_data *pdata = pdev->dev.platform_data;
+ struct omap_sr *sr_info;
+
+ if (!pdata) {
+ dev_err(&pdev->dev, "%s: platform data missing\n", __func__);
+ return;
+ }
+
+ sr_info = _sr_lookup(pdata->voltdm);
+ if (IS_ERR(sr_info)) {
+ dev_warn(&pdev->dev, "%s: omap_sr struct not found\n",
+ __func__);
+ return;
+ }
+
+ if (sr_info->autocomp_active)
+ sr_stop_vddautocomp(sr_info);
+
+ return;
+}
+
static struct platform_driver smartreflex_driver = {
.remove = __devexit_p(omap_sr_remove),
+ .shutdown = __devexit_p(omap_sr_shutdown),
.driver = {
.name = "smartreflex",
},
@@ -1042,12 +1151,12 @@ static int __init sr_init(void)
return 0;
}
+late_initcall(sr_init);
static void __exit sr_exit(void)
{
platform_driver_unregister(&smartreflex_driver);
}
-late_initcall(sr_init);
module_exit(sr_exit);
MODULE_DESCRIPTION("OMAP Smartreflex Driver");
diff --git a/arch/arm/mach-omap2/smartreflex.h b/arch/arm/mach-omap2/smartreflex.h
index 5f35b9e2555603fcbd44f1150439a371c31bbde1..5809141171f8c6f0553a6c0607964ab1e443780f 100644
--- a/arch/arm/mach-omap2/smartreflex.h
+++ b/arch/arm/mach-omap2/smartreflex.h
@@ -152,6 +152,15 @@ struct omap_sr_pmic_data {
void (*sr_pmic_init) (void);
};
+/**
+ * struct omap_smartreflex_dev_attr - Smartreflex Device attribute.
+ *
+ * @sensor_voltdm_name: Name of voltdomain of SR instance
+ */
+struct omap_smartreflex_dev_attr {
+ const char *sensor_voltdm_name;
+};
+
#ifdef CONFIG_OMAP_SMARTREFLEX
/*
* The smart reflex driver supports CLASS1 CLASS2 and CLASS3 SR.
@@ -231,6 +240,7 @@ void omap_sr_register_pmic(struct omap_sr_pmic_data *pmic_data);
int sr_enable(struct voltagedomain *voltdm, unsigned long volt);
void sr_disable(struct voltagedomain *voltdm);
int sr_configure_errgen(struct voltagedomain *voltdm);
+int sr_disable_errgen(struct voltagedomain *voltdm);
int sr_configure_minmax(struct voltagedomain *voltdm);
/* API to register the smartreflex class driver with the smartreflex driver */
diff --git a/arch/arm/mach-omap2/sr_device.c b/arch/arm/mach-omap2/sr_device.c
index 78c9437913ceeb9b1512af753c83a173d435251a..a503e1e8358c1f011b193a22f33c48ff38ce89d2 100644
--- a/arch/arm/mach-omap2/sr_device.c
+++ b/arch/arm/mach-omap2/sr_device.c
@@ -74,6 +74,7 @@ static int __init sr_dev_init(struct omap_hwmod *oh, void *user)
struct omap_sr_data *sr_data;
struct platform_device *pdev;
struct omap_volt_data *volt_data;
+ struct omap_smartreflex_dev_attr *sr_dev_attr;
char *name = "smartreflex";
static int i;
@@ -84,9 +85,11 @@ static int __init sr_dev_init(struct omap_hwmod *oh, void *user)
return -ENOMEM;
}
- if (!oh->vdd_name) {
+ sr_dev_attr = (struct omap_smartreflex_dev_attr *)oh->dev_attr;
+ if (!sr_dev_attr || !sr_dev_attr->sensor_voltdm_name) {
pr_err("%s: No voltage domain specified for %s."
- "Cannot initialize\n", __func__, oh->name);
+ "Cannot initialize\n", __func__,
+ oh->name);
goto exit;
}
@@ -94,10 +97,10 @@ static int __init sr_dev_init(struct omap_hwmod *oh, void *user)
sr_data->senn_mod = 0x1;
sr_data->senp_mod = 0x1;
- sr_data->voltdm = voltdm_lookup(oh->vdd_name);
+ sr_data->voltdm = voltdm_lookup(sr_dev_attr->sensor_voltdm_name);
if (IS_ERR(sr_data->voltdm)) {
pr_err("%s: Unable to get voltage domain pointer for VDD %s\n",
- __func__, oh->vdd_name);
+ __func__, sr_dev_attr->sensor_voltdm_name);
goto exit;
}
diff --git a/arch/arm/mach-pxa/devices.c b/arch/arm/mach-pxa/devices.c
index 5bc13121eac5d15eb239e3992b18f90720f67416..84f2d7015cfeced0850588ba7572968f1943f630 100644
--- a/arch/arm/mach-pxa/devices.c
+++ b/arch/arm/mach-pxa/devices.c
@@ -406,20 +406,17 @@ static struct resource pxa_rtc_resources[] = {
[1] = {
.start = IRQ_RTC1Hz,
.end = IRQ_RTC1Hz,
+ .name = "rtc 1Hz",
.flags = IORESOURCE_IRQ,
},
[2] = {
.start = IRQ_RTCAlrm,
.end = IRQ_RTCAlrm,
+ .name = "rtc alarm",
.flags = IORESOURCE_IRQ,
},
};
-struct platform_device sa1100_device_rtc = {
- .name = "sa1100-rtc",
- .id = -1,
-};
-
struct platform_device pxa_device_rtc = {
.name = "pxa-rtc",
.id = -1,
@@ -427,6 +424,27 @@ struct platform_device pxa_device_rtc = {
.resource = pxa_rtc_resources,
};
+static struct resource sa1100_rtc_resources[] = {
+ {
+ .start = IRQ_RTC1Hz,
+ .end = IRQ_RTC1Hz,
+ .name = "rtc 1Hz",
+ .flags = IORESOURCE_IRQ,
+ }, {
+ .start = IRQ_RTCAlrm,
+ .end = IRQ_RTCAlrm,
+ .name = "rtc alarm",
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device sa1100_device_rtc = {
+ .name = "sa1100-rtc",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(sa1100_rtc_resources),
+ .resource = sa1100_rtc_resources,
+};
+
static struct resource pxa_ac97_resources[] = {
[0] = {
.start = 0x40500000,
diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c
index f309bf975202e2cd89921092a33bb684f209f5df..3fa929d4a4f5b748ec9885c11d255d33aa00b6cd 100644
--- a/arch/arm/mach-pxa/hx4700.c
+++ b/arch/arm/mach-pxa/hx4700.c
@@ -28,7 +28,8 @@
#include <linux/mtd/physmap.h>
#include <linux/pda_power.h>
#include <linux/pwm_backlight.h>
-#include <linux/regulator/bq24022.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/gpio-regulator.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/max1586.h>
#include <linux/spi/ads7846.h>
@@ -698,14 +699,34 @@ static struct regulator_init_data bq24022_init_data = {
.consumer_supplies = bq24022_consumers,
};
-static struct bq24022_mach_info bq24022_info = {
- .gpio_nce = GPIO72_HX4700_BQ24022_nCHARGE_EN,
- .gpio_iset2 = GPIO96_HX4700_BQ24022_ISET2,
- .init_data = &bq24022_init_data,
+static struct gpio bq24022_gpios[] = {
+ { GPIO96_HX4700_BQ24022_ISET2, GPIOF_OUT_INIT_LOW, "bq24022_iset2" },
+};
+
+static struct gpio_regulator_state bq24022_states[] = {
+ { .value = 100000, .gpios = (0 << 0) },
+ { .value = 500000, .gpios = (1 << 0) },
+};
+
+static struct gpio_regulator_config bq24022_info = {
+ .supply_name = "bq24022",
+
+ .enable_gpio = GPIO72_HX4700_BQ24022_nCHARGE_EN,
+ .enable_high = 0,
+ .enabled_at_boot = 0,
+
+ .gpios = bq24022_gpios,
+ .nr_gpios = ARRAY_SIZE(bq24022_gpios),
+
+ .states = bq24022_states,
+ .nr_states = ARRAY_SIZE(bq24022_states),
+
+ .type = REGULATOR_CURRENT,
+ .init_data = &bq24022_init_data,
};
static struct platform_device bq24022 = {
- .name = "bq24022",
+ .name = "gpio-regulator",
.id = -1,
.dev = {
.platform_data = &bq24022_info,
diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c
index 3d6baf91396cd2cd52f2b41163f17a17cea6aa5d..5e26f3e93fddf5f8e4a56adb3cc53806839b6e36 100644
--- a/arch/arm/mach-pxa/magician.c
+++ b/arch/arm/mach-pxa/magician.c
@@ -25,7 +25,8 @@
#include <linux/mtd/physmap.h>
#include <linux/pda_power.h>
#include <linux/pwm_backlight.h>
-#include <linux/regulator/bq24022.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/gpio-regulator.h>
#include <linux/regulator/machine.h>
#include <linux/usb/gpio_vbus.h>
#include <linux/i2c/pxa-i2c.h>
@@ -596,14 +597,34 @@ static struct regulator_init_data bq24022_init_data = {
.consumer_supplies = bq24022_consumers,
};
-static struct bq24022_mach_info bq24022_info = {
- .gpio_nce = GPIO30_MAGICIAN_BQ24022_nCHARGE_EN,
- .gpio_iset2 = EGPIO_MAGICIAN_BQ24022_ISET2,
- .init_data = &bq24022_init_data,
+static struct gpio bq24022_gpios[] = {
+ { EGPIO_MAGICIAN_BQ24022_ISET2, GPIOF_OUT_INIT_LOW, "bq24022_iset2" },
+};
+
+static struct gpio_regulator_state bq24022_states[] = {
+ { .value = 100000, .gpios = (0 << 0) },
+ { .value = 500000, .gpios = (1 << 0) },
+};
+
+static struct gpio_regulator_config bq24022_info = {
+ .supply_name = "bq24022",
+
+ .enable_gpio = GPIO30_MAGICIAN_BQ24022_nCHARGE_EN,
+ .enable_high = 0,
+ .enabled_at_boot = 0,
+
+ .gpios = bq24022_gpios,
+ .nr_gpios = ARRAY_SIZE(bq24022_gpios),
+
+ .states = bq24022_states,
+ .nr_states = ARRAY_SIZE(bq24022_states),
+
+ .type = REGULATOR_CURRENT,
+ .init_data = &bq24022_init_data,
};
static struct platform_device bq24022 = {
- .name = "bq24022",
+ .name = "gpio-regulator",
.id = -1,
.dev = {
.platform_data = &bq24022_info,
diff --git a/arch/arm/mach-pxa/pxa3xx.c b/arch/arm/mach-pxa/pxa3xx.c
index 3918a672238e4a368f0474c699ebc1c2cb680bb7..1570d457fea3b87f52629ce2b1982c27229c3d40 100644
--- a/arch/arm/mach-pxa/pxa3xx.c
+++ b/arch/arm/mach-pxa/pxa3xx.c
@@ -89,6 +89,7 @@ static struct clk_lookup pxa3xx_clkregs[] = {
INIT_CLKREG(&clk_pxa3xx_mmc2, "pxa2xx-mci.1", NULL),
INIT_CLKREG(&clk_pxa3xx_smemc, "pxa2xx-pcmcia", NULL),
INIT_CLKREG(&clk_pxa3xx_gpio, "pxa-gpio", NULL),
+ INIT_CLKREG(&clk_dummy, "sa1100-rtc", NULL),
};
#ifdef CONFIG_PM
diff --git a/arch/arm/mach-pxa/pxa95x.c b/arch/arm/mach-pxa/pxa95x.c
index 5ce434b95e87a52941f38ca8e023753b940802e5..47601f80e6e7e9b64c8236541695dd68e0f24979 100644
--- a/arch/arm/mach-pxa/pxa95x.c
+++ b/arch/arm/mach-pxa/pxa95x.c
@@ -231,6 +231,7 @@ static struct clk_lookup pxa95x_clkregs[] = {
INIT_CLKREG(&clk_pxa95x_pwm0, "pxa27x-pwm.0", NULL),
INIT_CLKREG(&clk_pxa95x_pwm1, "pxa27x-pwm.1", NULL),
INIT_CLKREG(&clk_pxa95x_gpio, "pxa-gpio", NULL),
+ INIT_CLKREG(&clk_dummy, "sa1100-rtc", NULL),
};
void __init pxa95x_init_irq(void)
diff --git a/arch/arm/mach-s3c24xx/s3c2416.c b/arch/arm/mach-s3c24xx/s3c2416.c
index 08bb0355159db059934eac0c57458553ec1e5286..0e9a71c90ed7343f86ed077d820926b8f2b03741 100644
--- a/arch/arm/mach-s3c24xx/s3c2416.c
+++ b/arch/arm/mach-s3c24xx/s3c2416.c
@@ -59,6 +59,7 @@
#include <plat/fb-core.h>
#include <plat/nand-core.h>
#include <plat/adc-core.h>
+#include <plat/rtc-core.h>
static struct map_desc s3c2416_iodesc[] __initdata = {
IODESC_ENT(WATCHDOG),
@@ -98,6 +99,7 @@ int __init s3c2416_init(void)
s3c_fb_setname("s3c2443-fb");
s3c_adc_setname("s3c2416-adc");
+ s3c_rtc_setname("s3c2416-rtc");
#ifdef CONFIG_PM
register_syscore_ops(&s3c2416_pm_syscore_ops);
diff --git a/arch/arm/mach-s3c24xx/s3c2443.c b/arch/arm/mach-s3c24xx/s3c2443.c
index b9deaeb0dfff5ea0dbc3b1f83cadd25c78854599..b7778a9dafaff8e05946119d8c9ffaf0b2ceec90 100644
--- a/arch/arm/mach-s3c24xx/s3c2443.c
+++ b/arch/arm/mach-s3c24xx/s3c2443.c
@@ -41,6 +41,7 @@
#include <plat/fb-core.h>
#include <plat/nand-core.h>
#include <plat/adc-core.h>
+#include <plat/rtc-core.h>
static struct map_desc s3c2443_iodesc[] __initdata = {
IODESC_ENT(WATCHDOG),
@@ -73,6 +74,7 @@ int __init s3c2443_init(void)
s3c_fb_setname("s3c2443-fb");
s3c_adc_setname("s3c2443-adc");
+ s3c_rtc_setname("s3c2443-rtc");
/* change WDT IRQ number */
s3c_device_wdt.resource[1].start = IRQ_S3C2443_WDT;
diff --git a/arch/arm/mach-sa1100/clock.c b/arch/arm/mach-sa1100/clock.c
index dab3c6347a8f2d8e80bafba18b6916f8f97161f9..172ebd0ee0a2c9d7fe5371b5bebc6c505c8e303d 100644
--- a/arch/arm/mach-sa1100/clock.c
+++ b/arch/arm/mach-sa1100/clock.c
@@ -11,17 +11,29 @@
#include <linux/clk.h>
#include <linux/spinlock.h>
#include <linux/mutex.h>
+#include <linux/io.h>
+#include <linux/clkdev.h>
#include <mach/hardware.h>
-/*
- * Very simple clock implementation - we only have one clock to deal with.
- */
+struct clkops {
+ void (*enable)(struct clk *);
+ void (*disable)(struct clk *);
+};
+
struct clk {
+ const struct clkops *ops;
unsigned int enabled;
};
-static void clk_gpio27_enable(void)
+#define DEFINE_CLK(_name, _ops) \
+struct clk clk_##_name = { \
+ .ops = _ops, \
+ }
+
+static DEFINE_SPINLOCK(clocks_lock);
+
+static void clk_gpio27_enable(struct clk *clk)
{
/*
* First, set up the 3.6864MHz clock on GPIO 27 for the SA-1111:
@@ -32,38 +44,24 @@ static void clk_gpio27_enable(void)
TUCR = TUCR_3_6864MHz;
}
-static void clk_gpio27_disable(void)
+static void clk_gpio27_disable(struct clk *clk)
{
TUCR = 0;
GPDR &= ~GPIO_32_768kHz;
GAFR &= ~GPIO_32_768kHz;
}
-static struct clk clk_gpio27;
-
-static DEFINE_SPINLOCK(clocks_lock);
-
-struct clk *clk_get(struct device *dev, const char *id)
-{
- const char *devname = dev_name(dev);
-
- return strcmp(devname, "sa1111.0") ? ERR_PTR(-ENOENT) : &clk_gpio27;
-}
-EXPORT_SYMBOL(clk_get);
-
-void clk_put(struct clk *clk)
-{
-}
-EXPORT_SYMBOL(clk_put);
-
int clk_enable(struct clk *clk)
{
unsigned long flags;
- spin_lock_irqsave(&clocks_lock, flags);
- if (clk->enabled++ == 0)
- clk_gpio27_enable();
- spin_unlock_irqrestore(&clocks_lock, flags);
+ if (clk) {
+ spin_lock_irqsave(&clocks_lock, flags);
+ if (clk->enabled++ == 0)
+ clk->ops->enable(clk);
+ spin_unlock_irqrestore(&clocks_lock, flags);
+ }
+
return 0;
}
EXPORT_SYMBOL(clk_enable);
@@ -72,17 +70,31 @@ void clk_disable(struct clk *clk)
{
unsigned long flags;
- WARN_ON(clk->enabled == 0);
-
- spin_lock_irqsave(&clocks_lock, flags);
- if (--clk->enabled == 0)
- clk_gpio27_disable();
- spin_unlock_irqrestore(&clocks_lock, flags);
+ if (clk) {
+ WARN_ON(clk->enabled == 0);
+ spin_lock_irqsave(&clocks_lock, flags);
+ if (--clk->enabled == 0)
+ clk->ops->disable(clk);
+ spin_unlock_irqrestore(&clocks_lock, flags);
+ }
}
EXPORT_SYMBOL(clk_disable);
-unsigned long clk_get_rate(struct clk *clk)
+const struct clkops clk_gpio27_ops = {
+ .enable = clk_gpio27_enable,
+ .disable = clk_gpio27_disable,
+};
+
+static DEFINE_CLK(gpio27, &clk_gpio27_ops);
+
+static struct clk_lookup sa11xx_clkregs[] = {
+ CLKDEV_INIT("sa1111.0", NULL, &clk_gpio27),
+ CLKDEV_INIT("sa1100-rtc", NULL, NULL),
+};
+
+static int __init sa11xx_clk_init(void)
{
- return 3686400;
+ clkdev_add_table(sa11xx_clkregs, ARRAY_SIZE(sa11xx_clkregs));
+ return 0;
}
-EXPORT_SYMBOL(clk_get_rate);
+core_initcall(sa11xx_clk_init);
diff --git a/arch/arm/mach-sa1100/generic.c b/arch/arm/mach-sa1100/generic.c
index bb10ee2cb89f11f82c801d7f9c1d8ced11c1c3b7..7c1ebf4a7920f140259b3da2896cd6bf6bef8081 100644
--- a/arch/arm/mach-sa1100/generic.c
+++ b/arch/arm/mach-sa1100/generic.c
@@ -345,9 +345,17 @@ void sa11x0_register_irda(struct irda_platform_data *irda)
sa11x0_register_device(&sa11x0ir_device, irda);
}
+static struct resource sa1100_rtc_resources[] = {
+ DEFINE_RES_MEM(0x90010000, 0x9001003f),
+ DEFINE_RES_IRQ_NAMED(IRQ_RTC1Hz, "rtc 1Hz"),
+ DEFINE_RES_IRQ_NAMED(IRQ_RTCAlrm, "rtc alarm"),
+};
+
static struct platform_device sa11x0rtc_device = {
.name = "sa1100-rtc",
.id = -1,
+ .num_resources = ARRAY_SIZE(sa1100_rtc_resources),
+ .resource = sa1100_rtc_resources,
};
static struct platform_device *sa11x0_devices[] __initdata = {
diff --git a/arch/arm/mach-tegra/Makefile b/arch/arm/mach-tegra/Makefile
index 76a79b8a1721058fcb4938de96ca8ca5405e7911..1dd2726986cfe70693ca511720f459c3ae003722 100644
--- a/arch/arm/mach-tegra/Makefile
+++ b/arch/arm/mach-tegra/Makefile
@@ -7,6 +7,7 @@ obj-y += clock.o
obj-y += timer.o
obj-y += pinmux.o
obj-y += fuse.o
+obj-y += pmc.o
obj-$(CONFIG_CPU_IDLE) += cpuidle.o
obj-$(CONFIG_CPU_IDLE) += sleep.o
obj-$(CONFIG_ARCH_TEGRA_2x_SOC) += powergate.o
@@ -18,7 +19,7 @@ obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += board-dt-tegra30.o
obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += tegra30_clocks.o
obj-$(CONFIG_SMP) += platsmp.o headsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
-obj-$(CONFIG_TEGRA_SYSTEM_DMA) += dma.o
+obj-$(CONFIG_TEGRA_SYSTEM_DMA) += dma.o apbio.o
obj-$(CONFIG_CPU_FREQ) += cpu-tegra.o
obj-$(CONFIG_TEGRA_PCI) += pcie.o
obj-$(CONFIG_USB_SUPPORT) += usb_phy.o
diff --git a/arch/arm/mach-tegra/apbio.c b/arch/arm/mach-tegra/apbio.c
new file mode 100644
index 0000000000000000000000000000000000000000..e75451e517bdd2b55a4c94bc17be3abaddc24c1c
--- /dev/null
+++ b/arch/arm/mach-tegra/apbio.c
@@ -0,0 +1,145 @@
+/*
+ * Copyright (C) 2010 NVIDIA Corporation.
+ * Copyright (C) 2010 Google, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <linux/dma-mapping.h>
+#include <linux/spinlock.h>
+#include <linux/completion.h>
+#include <linux/sched.h>
+#include <linux/mutex.h>
+
+#include <mach/dma.h>
+#include <mach/iomap.h>
+
+#include "apbio.h"
+
+static DEFINE_MUTEX(tegra_apb_dma_lock);
+
+static struct tegra_dma_channel *tegra_apb_dma;
+static u32 *tegra_apb_bb;
+static dma_addr_t tegra_apb_bb_phys;
+static DECLARE_COMPLETION(tegra_apb_wait);
+
+bool tegra_apb_init(void)
+{
+ struct tegra_dma_channel *ch;
+
+ mutex_lock(&tegra_apb_dma_lock);
+
+ /* Check to see if we raced to setup */
+ if (tegra_apb_dma)
+ goto out;
+
+ ch = tegra_dma_allocate_channel(TEGRA_DMA_MODE_ONESHOT |
+ TEGRA_DMA_SHARED);
+
+ if (!ch)
+ goto out_fail;
+
+ tegra_apb_bb = dma_alloc_coherent(NULL, sizeof(u32),
+ &tegra_apb_bb_phys, GFP_KERNEL);
+ if (!tegra_apb_bb) {
+ pr_err("%s: can not allocate bounce buffer\n", __func__);
+ tegra_dma_free_channel(ch);
+ goto out_fail;
+ }
+
+ tegra_apb_dma = ch;
+out:
+ mutex_unlock(&tegra_apb_dma_lock);
+ return true;
+
+out_fail:
+ mutex_unlock(&tegra_apb_dma_lock);
+ return false;
+}
+
+static void apb_dma_complete(struct tegra_dma_req *req)
+{
+ complete(&tegra_apb_wait);
+}
+
+u32 tegra_apb_readl(unsigned long offset)
+{
+ struct tegra_dma_req req;
+ int ret;
+
+ if (!tegra_apb_dma && !tegra_apb_init())
+ return readl(IO_TO_VIRT(offset));
+
+ mutex_lock(&tegra_apb_dma_lock);
+ req.complete = apb_dma_complete;
+ req.to_memory = 1;
+ req.dest_addr = tegra_apb_bb_phys;
+ req.dest_bus_width = 32;
+ req.dest_wrap = 1;
+ req.source_addr = offset;
+ req.source_bus_width = 32;
+ req.source_wrap = 4;
+ req.req_sel = TEGRA_DMA_REQ_SEL_CNTR;
+ req.size = 4;
+
+ INIT_COMPLETION(tegra_apb_wait);
+
+ tegra_dma_enqueue_req(tegra_apb_dma, &req);
+
+ ret = wait_for_completion_timeout(&tegra_apb_wait,
+ msecs_to_jiffies(50));
+
+ if (WARN(ret == 0, "apb read dma timed out")) {
+ tegra_dma_dequeue_req(tegra_apb_dma, &req);
+ *(u32 *)tegra_apb_bb = 0;
+ }
+
+ mutex_unlock(&tegra_apb_dma_lock);
+ return *((u32 *)tegra_apb_bb);
+}
+
+void tegra_apb_writel(u32 value, unsigned long offset)
+{
+ struct tegra_dma_req req;
+ int ret;
+
+ if (!tegra_apb_dma && !tegra_apb_init()) {
+ writel(value, IO_TO_VIRT(offset));
+ return;
+ }
+
+ mutex_lock(&tegra_apb_dma_lock);
+ *((u32 *)tegra_apb_bb) = value;
+ req.complete = apb_dma_complete;
+ req.to_memory = 0;
+ req.dest_addr = offset;
+ req.dest_wrap = 4;
+ req.dest_bus_width = 32;
+ req.source_addr = tegra_apb_bb_phys;
+ req.source_bus_width = 32;
+ req.source_wrap = 1;
+ req.req_sel = TEGRA_DMA_REQ_SEL_CNTR;
+ req.size = 4;
+
+ INIT_COMPLETION(tegra_apb_wait);
+
+ tegra_dma_enqueue_req(tegra_apb_dma, &req);
+
+ ret = wait_for_completion_timeout(&tegra_apb_wait,
+ msecs_to_jiffies(50));
+
+ if (WARN(ret == 0, "apb write dma timed out"))
+ tegra_dma_dequeue_req(tegra_apb_dma, &req);
+
+ mutex_unlock(&tegra_apb_dma_lock);
+}
diff --git a/arch/arm/mach-tegra/apbio.h b/arch/arm/mach-tegra/apbio.h
new file mode 100644
index 0000000000000000000000000000000000000000..8b49e8c89a648993ec7452d2550a5552998c03c6
--- /dev/null
+++ b/arch/arm/mach-tegra/apbio.h
@@ -0,0 +1,39 @@
+/*
+ * Copyright (C) 2010 NVIDIA Corporation.
+ * Copyright (C) 2010 Google, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __MACH_TEGRA_APBIO_H
+#define __MACH_TEGRA_APBIO_H
+
+#ifdef CONFIG_TEGRA_SYSTEM_DMA
+
+u32 tegra_apb_readl(unsigned long offset);
+void tegra_apb_writel(u32 value, unsigned long offset);
+
+#else
+#include <asm/io.h>
+#include <mach/io.h>
+
+static inline u32 tegra_apb_readl(unsigned long offset)
+{
+ return readl(IO_TO_VIRT(offset));
+}
+
+static inline void tegra_apb_writel(u32 value, unsigned long offset)
+{
+ writel(value, IO_TO_VIRT(offset));
+}
+#endif
+
+#endif
diff --git a/arch/arm/mach-tegra/board-harmony-power.c b/arch/arm/mach-tegra/board-harmony-power.c
index c0298b3f7d63d32ce4b776c46747943e14e4f4f1..82f32300796c082fe4f76c938ba76ac9b4bb1ff2 100644
--- a/arch/arm/mach-tegra/board-harmony-power.c
+++ b/arch/arm/mach-tegra/board-harmony-power.c
@@ -18,18 +18,13 @@
#include <linux/i2c.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
-#include <linux/io.h>
#include <linux/regulator/machine.h>
#include <linux/mfd/tps6586x.h>
-#include <mach/iomap.h>
#include <mach/irqs.h>
#include "board-harmony.h"
-#define PMC_CTRL 0x0
-#define PMC_CTRL_INTR_LOW (1 << 17)
-
static struct regulator_consumer_supply tps658621_ldo0_supply[] = {
REGULATOR_SUPPLY("pex_clk", NULL),
};
@@ -115,16 +110,6 @@ static struct i2c_board_info __initdata harmony_regulators[] = {
int __init harmony_regulator_init(void)
{
- void __iomem *pmc = IO_ADDRESS(TEGRA_PMC_BASE);
- u32 pmc_ctrl;
-
- /*
- * Configure the power management controller to trigger PMU
- * interrupts when low
- */
- pmc_ctrl = readl(pmc + PMC_CTRL);
- writel(pmc_ctrl | PMC_CTRL_INTR_LOW, pmc + PMC_CTRL);
-
i2c_register_board_info(3, harmony_regulators, 1);
return 0;
diff --git a/arch/arm/mach-tegra/board-harmony.c b/arch/arm/mach-tegra/board-harmony.c
index 789bdc9e8f913ddb26e46e1a4b827a2b0b6f51fa..c00aadb01e097f70e63909e0fd05d43f35f12f44 100644
--- a/arch/arm/mach-tegra/board-harmony.c
+++ b/arch/arm/mach-tegra/board-harmony.c
@@ -101,7 +101,6 @@ static struct wm8903_platform_data harmony_wm8903_pdata = {
static struct i2c_board_info __initdata wm8903_board_info = {
I2C_BOARD_INFO("wm8903", 0x1a),
.platform_data = &harmony_wm8903_pdata,
- .irq = TEGRA_GPIO_TO_IRQ(TEGRA_GPIO_CDC_IRQ),
};
static void __init harmony_i2c_init(void)
@@ -111,6 +110,7 @@ static void __init harmony_i2c_init(void)
platform_device_register(&tegra_i2c_device3);
platform_device_register(&tegra_i2c_device4);
+ wm8903_board_info.irq = gpio_to_irq(TEGRA_GPIO_CDC_IRQ);
i2c_register_board_info(0, &wm8903_board_info, 1);
}
diff --git a/arch/arm/mach-tegra/board-seaboard.c b/arch/arm/mach-tegra/board-seaboard.c
index ebac65f52510d4c4eb65093ab0fa79210e83940a..d669847f0485bdfffaf42e44290154777405f81b 100644
--- a/arch/arm/mach-tegra/board-seaboard.c
+++ b/arch/arm/mach-tegra/board-seaboard.c
@@ -159,7 +159,6 @@ static struct platform_device *seaboard_devices[] __initdata = {
static struct i2c_board_info __initdata isl29018_device = {
I2C_BOARD_INFO("isl29018", 0x44),
- .irq = TEGRA_GPIO_TO_IRQ(TEGRA_GPIO_ISL29018_IRQ),
};
static struct i2c_board_info __initdata adt7461_device = {
@@ -183,7 +182,6 @@ static struct wm8903_platform_data wm8903_pdata = {
static struct i2c_board_info __initdata wm8903_device = {
I2C_BOARD_INFO("wm8903", 0x1a),
.platform_data = &wm8903_pdata,
- .irq = TEGRA_GPIO_TO_IRQ(TEGRA_GPIO_CDC_IRQ),
};
static int seaboard_ehci_init(void)
@@ -214,7 +212,10 @@ static void __init seaboard_i2c_init(void)
gpio_request(TEGRA_GPIO_ISL29018_IRQ, "isl29018");
gpio_direction_input(TEGRA_GPIO_ISL29018_IRQ);
+ isl29018_device.irq = gpio_to_irq(TEGRA_GPIO_ISL29018_IRQ);
i2c_register_board_info(0, &isl29018_device, 1);
+
+ wm8903_device.irq = gpio_to_irq(TEGRA_GPIO_CDC_IRQ);
i2c_register_board_info(0, &wm8903_device, 1);
i2c_register_board_info(3, &adt7461_device, 1);
diff --git a/arch/arm/mach-tegra/common.c b/arch/arm/mach-tegra/common.c
index 6c93cd0e520c48075744d3d2940f98ebab47a259..2f86fcca64a6b1cd1006103f256447dff7e397f6 100644
--- a/arch/arm/mach-tegra/common.c
+++ b/arch/arm/mach-tegra/common.c
@@ -31,6 +31,24 @@
#include "board.h"
#include "clock.h"
#include "fuse.h"
+#include "pmc.h"
+
+/*
+ * Storage for debug-macro.S's state.
+ *
+ * This must be in .data not .bss so that it gets initialized each time the
+ * kernel is loaded. The data is declared here rather than debug-macro.S so
+ * that multiple inclusions of debug-macro.S point at the same data.
+ */
+#define TEGRA_DEBUG_UART_OFFSET (TEGRA_DEBUG_UART_BASE & 0xFFFF)
+u32 tegra_uart_config[3] = {
+ /* Debug UART initialization required */
+ 1,
+ /* Debug UART physical address */
+ (u32)(IO_APB_PHYS + TEGRA_DEBUG_UART_OFFSET),
+ /* Debug UART virtual address */
+ (u32)(IO_APB_VIRT + TEGRA_DEBUG_UART_OFFSET),
+};
#ifdef CONFIG_OF
static const struct of_device_id tegra_dt_irq_match[] __initconst = {
@@ -99,6 +117,7 @@ void __init tegra20_init_early(void)
tegra2_init_clocks();
tegra_clk_init_from_table(tegra20_clk_init_table);
tegra_init_cache(0x331, 0x441);
+ tegra_pmc_init();
}
#endif
#ifdef CONFIG_ARCH_TEGRA_3x_SOC
@@ -106,5 +125,6 @@ void __init tegra30_init_early(void)
{
tegra30_init_clocks();
tegra_init_cache(0x441, 0x551);
+ tegra_pmc_init();
}
#endif
diff --git a/arch/arm/mach-tegra/dma.c b/arch/arm/mach-tegra/dma.c
index c0cf967e47d3bced9577a43d87c3c42c9465e251..abea4f6e2dd5cbc47aeb3a516fea05d27afe08d4 100644
--- a/arch/arm/mach-tegra/dma.c
+++ b/arch/arm/mach-tegra/dma.c
@@ -33,6 +33,8 @@
#include <mach/iomap.h>
#include <mach/suspend.h>
+#include "apbio.h"
+
#define APB_DMA_GEN 0x000
#define GEN_ENABLE (1<<31)
@@ -50,8 +52,6 @@
#define CSR_ONCE (1<<27)
#define CSR_FLOW (1<<21)
#define CSR_REQ_SEL_SHIFT 16
-#define CSR_REQ_SEL_MASK (0x1F<<CSR_REQ_SEL_SHIFT)
-#define CSR_REQ_SEL_INVALID (31<<CSR_REQ_SEL_SHIFT)
#define CSR_WCOUNT_SHIFT 2
#define CSR_WCOUNT_MASK 0xFFFC
@@ -133,6 +133,7 @@ struct tegra_dma_channel {
static bool tegra_dma_initialized;
static DEFINE_MUTEX(tegra_dma_lock);
+static DEFINE_SPINLOCK(enable_lock);
static DECLARE_BITMAP(channel_usage, NV_DMA_MAX_CHANNELS);
static struct tegra_dma_channel dma_channels[NV_DMA_MAX_CHANNELS];
@@ -180,36 +181,94 @@ static void tegra_dma_stop(struct tegra_dma_channel *ch)
static int tegra_dma_cancel(struct tegra_dma_channel *ch)
{
- u32 csr;
unsigned long irq_flags;
spin_lock_irqsave(&ch->lock, irq_flags);
while (!list_empty(&ch->list))
list_del(ch->list.next);
- csr = readl(ch->addr + APB_DMA_CHAN_CSR);
- csr &= ~CSR_REQ_SEL_MASK;
- csr |= CSR_REQ_SEL_INVALID;
- writel(csr, ch->addr + APB_DMA_CHAN_CSR);
-
tegra_dma_stop(ch);
spin_unlock_irqrestore(&ch->lock, irq_flags);
return 0;
}
+static unsigned int get_channel_status(struct tegra_dma_channel *ch,
+ struct tegra_dma_req *req, bool is_stop_dma)
+{
+ void __iomem *addr = IO_ADDRESS(TEGRA_APB_DMA_BASE);
+ unsigned int status;
+
+ if (is_stop_dma) {
+ /*
+ * STOP the DMA and get the transfer count.
+ * Getting the transfer count is tricky.
+ * - Globally disable DMA on all channels
+ * - Read the channel's status register to know the number
+ * of pending bytes to be transfered.
+ * - Stop the dma channel
+ * - Globally re-enable DMA to resume other transfers
+ */
+ spin_lock(&enable_lock);
+ writel(0, addr + APB_DMA_GEN);
+ udelay(20);
+ status = readl(ch->addr + APB_DMA_CHAN_STA);
+ tegra_dma_stop(ch);
+ writel(GEN_ENABLE, addr + APB_DMA_GEN);
+ spin_unlock(&enable_lock);
+ if (status & STA_ISE_EOC) {
+ pr_err("Got Dma Int here clearing");
+ writel(status, ch->addr + APB_DMA_CHAN_STA);
+ }
+ req->status = TEGRA_DMA_REQ_ERROR_ABORTED;
+ } else {
+ status = readl(ch->addr + APB_DMA_CHAN_STA);
+ }
+ return status;
+}
+
+/* should be called with the channel lock held */
+static unsigned int dma_active_count(struct tegra_dma_channel *ch,
+ struct tegra_dma_req *req, unsigned int status)
+{
+ unsigned int to_transfer;
+ unsigned int req_transfer_count;
+ unsigned int bytes_transferred;
+
+ to_transfer = ((status & STA_COUNT_MASK) >> STA_COUNT_SHIFT) + 1;
+ req_transfer_count = ch->req_transfer_count + 1;
+ bytes_transferred = req_transfer_count;
+ if (status & STA_BUSY)
+ bytes_transferred -= to_transfer;
+ /*
+ * In continuous transfer mode, DMA only tracks the count of the
+ * half DMA buffer. So, if the DMA already finished half the DMA
+ * then add the half buffer to the completed count.
+ */
+ if (ch->mode & TEGRA_DMA_MODE_CONTINOUS) {
+ if (req->buffer_status == TEGRA_DMA_REQ_BUF_STATUS_HALF_FULL)
+ bytes_transferred += req_transfer_count;
+ if (status & STA_ISE_EOC)
+ bytes_transferred += req_transfer_count;
+ }
+ bytes_transferred *= 4;
+ return bytes_transferred;
+}
+
int tegra_dma_dequeue_req(struct tegra_dma_channel *ch,
struct tegra_dma_req *_req)
{
- unsigned int csr;
unsigned int status;
struct tegra_dma_req *req = NULL;
int found = 0;
unsigned long irq_flags;
- int to_transfer;
- int req_transfer_count;
+ int stop = 0;
spin_lock_irqsave(&ch->lock, irq_flags);
+
+ if (list_entry(ch->list.next, struct tegra_dma_req, node) == _req)
+ stop = 1;
+
list_for_each_entry(req, &ch->list, node) {
if (req == _req) {
list_del(&req->node);
@@ -222,47 +281,12 @@ int tegra_dma_dequeue_req(struct tegra_dma_channel *ch,
return 0;
}
- /* STOP the DMA and get the transfer count.
- * Getting the transfer count is tricky.
- * - Change the source selector to invalid to stop the DMA from
- * FIFO to memory.
- * - Read the status register to know the number of pending
- * bytes to be transferred.
- * - Finally stop or program the DMA to the next buffer in the
- * list.
- */
- csr = readl(ch->addr + APB_DMA_CHAN_CSR);
- csr &= ~CSR_REQ_SEL_MASK;
- csr |= CSR_REQ_SEL_INVALID;
- writel(csr, ch->addr + APB_DMA_CHAN_CSR);
-
- /* Get the transfer count */
- status = readl(ch->addr + APB_DMA_CHAN_STA);
- to_transfer = (status & STA_COUNT_MASK) >> STA_COUNT_SHIFT;
- req_transfer_count = ch->req_transfer_count;
- req_transfer_count += 1;
- to_transfer += 1;
-
- req->bytes_transferred = req_transfer_count;
-
- if (status & STA_BUSY)
- req->bytes_transferred -= to_transfer;
-
- /* In continuous transfer mode, DMA only tracks the count of the
- * half DMA buffer. So, if the DMA already finished half the DMA
- * then add the half buffer to the completed count.
- *
- * FIXME: There can be a race here. What if the req to
- * dequue happens at the same time as the DMA just moved to
- * the new buffer and SW didn't yet received the interrupt?
- */
- if (ch->mode & TEGRA_DMA_MODE_CONTINOUS)
- if (req->buffer_status == TEGRA_DMA_REQ_BUF_STATUS_HALF_FULL)
- req->bytes_transferred += req_transfer_count;
+ if (!stop)
+ goto skip_stop_dma;
- req->bytes_transferred *= 4;
+ status = get_channel_status(ch, req, true);
+ req->bytes_transferred = dma_active_count(ch, req, status);
- tegra_dma_stop(ch);
if (!list_empty(&ch->list)) {
/* if the list is not empty, queue the next request */
struct tegra_dma_req *next_req;
@@ -270,6 +294,8 @@ int tegra_dma_dequeue_req(struct tegra_dma_channel *ch,
typeof(*next_req), node);
tegra_dma_update_hw(ch, next_req);
}
+
+skip_stop_dma:
req->status = -TEGRA_DMA_REQ_ERROR_ABORTED;
spin_unlock_irqrestore(&ch->lock, irq_flags);
@@ -357,7 +383,7 @@ struct tegra_dma_channel *tegra_dma_allocate_channel(int mode)
int channel;
struct tegra_dma_channel *ch = NULL;
- if (WARN_ON(!tegra_dma_initialized))
+ if (!tegra_dma_initialized)
return NULL;
mutex_lock(&tegra_dma_lock);
diff --git a/arch/arm/mach-tegra/fuse.c b/arch/arm/mach-tegra/fuse.c
index ea49bd93c6b9dbdb374a2fbb72f6b79fc2be1ad6..c1afb2738769d4be34a75e04aff95ad1a5ca8a9d 100644
--- a/arch/arm/mach-tegra/fuse.c
+++ b/arch/arm/mach-tegra/fuse.c
@@ -19,25 +19,75 @@
#include <linux/kernel.h>
#include <linux/io.h>
-#include <linux/module.h>
+#include <linux/export.h>
#include <mach/iomap.h>
#include "fuse.h"
+#include "apbio.h"
#define FUSE_UID_LOW 0x108
#define FUSE_UID_HIGH 0x10c
#define FUSE_SKU_INFO 0x110
#define FUSE_SPARE_BIT 0x200
-static inline u32 fuse_readl(unsigned long offset)
+int tegra_sku_id;
+int tegra_cpu_process_id;
+int tegra_core_process_id;
+enum tegra_revision tegra_revision;
+
+/* The BCT to use at boot is specified by board straps that can be read
+ * through a APB misc register and decoded. 2 bits, i.e. 4 possible BCTs.
+ */
+int tegra_bct_strapping;
+
+#define STRAP_OPT 0x008
+#define GMI_AD0 (1 << 4)
+#define GMI_AD1 (1 << 5)
+#define RAM_ID_MASK (GMI_AD0 | GMI_AD1)
+#define RAM_CODE_SHIFT 4
+
+static const char *tegra_revision_name[TEGRA_REVISION_MAX] = {
+ [TEGRA_REVISION_UNKNOWN] = "unknown",
+ [TEGRA_REVISION_A01] = "A01",
+ [TEGRA_REVISION_A02] = "A02",
+ [TEGRA_REVISION_A03] = "A03",
+ [TEGRA_REVISION_A03p] = "A03 prime",
+ [TEGRA_REVISION_A04] = "A04",
+};
+
+static inline u32 tegra_fuse_readl(unsigned long offset)
+{
+ return tegra_apb_readl(TEGRA_FUSE_BASE + offset);
+}
+
+static inline bool get_spare_fuse(int bit)
{
- return readl(IO_TO_VIRT(TEGRA_FUSE_BASE + offset));
+ return tegra_fuse_readl(FUSE_SPARE_BIT + bit * 4);
}
-static inline void fuse_writel(u32 value, unsigned long offset)
+static enum tegra_revision tegra_get_revision(void)
{
- writel(value, IO_TO_VIRT(TEGRA_FUSE_BASE + offset));
+ void __iomem *chip_id = IO_ADDRESS(TEGRA_APB_MISC_BASE) + 0x804;
+ u32 id = readl(chip_id);
+ u32 minor_rev = (id >> 16) & 0xf;
+ u32 chipid = (id >> 8) & 0xff;
+
+ switch (minor_rev) {
+ case 1:
+ return TEGRA_REVISION_A01;
+ case 2:
+ return TEGRA_REVISION_A02;
+ case 3:
+ if (chipid == 0x20 && (get_spare_fuse(18) || get_spare_fuse(19)))
+ return TEGRA_REVISION_A03p;
+ else
+ return TEGRA_REVISION_A03;
+ case 4:
+ return TEGRA_REVISION_A04;
+ default:
+ return TEGRA_REVISION_UNKNOWN;
+ }
}
void tegra_init_fuse(void)
@@ -46,41 +96,32 @@ void tegra_init_fuse(void)
reg |= 1 << 28;
writel(reg, IO_TO_VIRT(TEGRA_CLK_RESET_BASE + 0x48));
- pr_info("Tegra SKU: %d CPU Process: %d Core Process: %d\n",
- tegra_sku_id(), tegra_cpu_process_id(),
- tegra_core_process_id());
+ reg = tegra_fuse_readl(FUSE_SKU_INFO);
+ tegra_sku_id = reg & 0xFF;
+
+ reg = tegra_fuse_readl(FUSE_SPARE_BIT);
+ tegra_cpu_process_id = (reg >> 6) & 3;
+
+ reg = tegra_fuse_readl(FUSE_SPARE_BIT);
+ tegra_core_process_id = (reg >> 12) & 3;
+
+ reg = tegra_apb_readl(TEGRA_APB_MISC_BASE + STRAP_OPT);
+ tegra_bct_strapping = (reg & RAM_ID_MASK) >> RAM_CODE_SHIFT;
+
+ tegra_revision = tegra_get_revision();
+
+ pr_info("Tegra Revision: %s SKU: %d CPU Process: %d Core Process: %d\n",
+ tegra_revision_name[tegra_get_revision()],
+ tegra_sku_id, tegra_cpu_process_id,
+ tegra_core_process_id);
}
unsigned long long tegra_chip_uid(void)
{
unsigned long long lo, hi;
- lo = fuse_readl(FUSE_UID_LOW);
- hi = fuse_readl(FUSE_UID_HIGH);
+ lo = tegra_fuse_readl(FUSE_UID_LOW);
+ hi = tegra_fuse_readl(FUSE_UID_HIGH);
return (hi << 32ull) | lo;
}
EXPORT_SYMBOL(tegra_chip_uid);
-
-int tegra_sku_id(void)
-{
- int sku_id;
- u32 reg = fuse_readl(FUSE_SKU_INFO);
- sku_id = reg & 0xFF;
- return sku_id;
-}
-
-int tegra_cpu_process_id(void)
-{
- int cpu_process_id;
- u32 reg = fuse_readl(FUSE_SPARE_BIT);
- cpu_process_id = (reg >> 6) & 3;
- return cpu_process_id;
-}
-
-int tegra_core_process_id(void)
-{
- int core_process_id;
- u32 reg = fuse_readl(FUSE_SPARE_BIT);
- core_process_id = (reg >> 12) & 3;
- return core_process_id;
-}
diff --git a/arch/arm/mach-tegra/fuse.h b/arch/arm/mach-tegra/fuse.h
index 584b2e27dbda5679078ce2f60d552f98a4c13f3c..d65d2abf803b1da33ac70e909e0ae15477d2135a 100644
--- a/arch/arm/mach-tegra/fuse.h
+++ b/arch/arm/mach-tegra/fuse.h
@@ -1,6 +1,4 @@
/*
- * arch/arm/mach-tegra/fuse.c
- *
* Copyright (C) 2010 Google, Inc.
*
* Author:
@@ -17,8 +15,34 @@
*
*/
+#ifndef __MACH_TEGRA_FUSE_H
+#define __MACH_TEGRA_FUSE_H
+
+enum tegra_revision {
+ TEGRA_REVISION_UNKNOWN = 0,
+ TEGRA_REVISION_A01,
+ TEGRA_REVISION_A02,
+ TEGRA_REVISION_A03,
+ TEGRA_REVISION_A03p,
+ TEGRA_REVISION_A04,
+ TEGRA_REVISION_MAX,
+};
+
+#define SKU_ID_T20 8
+#define SKU_ID_T25SE 20
+#define SKU_ID_AP25 23
+#define SKU_ID_T25 24
+#define SKU_ID_AP25E 27
+#define SKU_ID_T25E 28
+
+extern int tegra_sku_id;
+extern int tegra_cpu_process_id;
+extern int tegra_core_process_id;
+extern enum tegra_revision tegra_revision;
+
+extern int tegra_bct_strapping;
+
unsigned long long tegra_chip_uid(void);
-int tegra_sku_id(void);
-int tegra_cpu_process_id(void);
-int tegra_core_process_id(void);
void tegra_init_fuse(void);
+
+#endif
diff --git a/arch/arm/mach-tegra/include/mach/debug-macro.S b/arch/arm/mach-tegra/include/mach/debug-macro.S
index 619abc63aee83748c918db3ce9cc08c1ea58d254..90069abd37bd84844c5fc29ce2fca73e66d9ec8e 100644
--- a/arch/arm/mach-tegra/include/mach/debug-macro.S
+++ b/arch/arm/mach-tegra/include/mach/debug-macro.S
@@ -1,11 +1,17 @@
/*
* arch/arm/mach-tegra/include/mach/debug-macro.S
*
- * Copyright (C) 2010 Google, Inc.
+ * Copyright (C) 2010,2011 Google, Inc.
+ * Copyright (C) 2011-2012 NVIDIA CORPORATION. All Rights Reserved.
*
* Author:
* Colin Cross <ccross@google.com>
* Erik Gilling <konkers@google.com>
+ * Doug Anderson <dianders@chromium.org>
+ * Stephen Warren <swarren@nvidia.com>
+ *
+ * Portions based on mach-omap2's debug-macro.S
+ * Copyright (C) 1994-1999 Russell King
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
@@ -18,18 +24,78 @@
*
*/
+#include <linux/serial_reg.h>
+
#include <mach/io.h>
#include <mach/iomap.h>
+#include <mach/irammap.h>
+
+ .macro addruart, rp, rv, tmp
+ adr \rp, 99f @ actual addr of 99f
+ ldr \rv, [\rp] @ linked addr is stored there
+ sub \rv, \rv, \rp @ offset between the two
+ ldr \rp, [\rp, #4] @ linked tegra_uart_config
+ sub \tmp, \rp, \rv @ actual tegra_uart_config
+ ldr \rp, [\tmp] @ Load tegra_uart_config
+ cmp \rp, #1 @ needs intitialization?
+ bne 100f @ no; go load the addresses
+ mov \rv, #0 @ yes; record init is done
+ str \rv, [\tmp]
+ mov \rp, #TEGRA_IRAM_BASE @ See if cookie is in IRAM
+ ldr \rv, [\rp, #TEGRA_IRAM_DEBUG_UART_OFFSET]
+ movw \rp, #TEGRA_IRAM_DEBUG_UART_COOKIE & 0xffff
+ movt \rp, #TEGRA_IRAM_DEBUG_UART_COOKIE >> 16
+ cmp \rv, \rp @ Cookie present?
+ bne 100f @ No, use default UART
+ mov \rp, #TEGRA_IRAM_BASE @ Load UART address from IRAM
+ ldr \rv, [\rp, #TEGRA_IRAM_DEBUG_UART_OFFSET + 4]
+ str \rv, [\tmp, #4] @ Store in tegra_uart_phys
+ sub \rv, \rv, #IO_APB_PHYS @ Calculate virt address
+ add \rv, \rv, #IO_APB_VIRT
+ str \rv, [\tmp, #8] @ Store in tegra_uart_virt
+ b 100f
+
+ .align
+99: .word .
+ .word tegra_uart_config
+ .ltorg
+
+100: ldr \rp, [\tmp, #4] @ Load tegra_uart_phys
+ ldr \rv, [\tmp, #8] @ Load tegra_uart_virt
+ .endm
+
+#define UART_SHIFT 2
+
+/*
+ * Code below is swiped from <asm/hardware/debug-8250.S>, but add an extra
+ * check to make sure that we aren't in the CONFIG_TEGRA_DEBUG_UART_NONE case.
+ * We use the fact that all 5 valid UART addresses all have something in the
+ * 2nd-to-lowest byte.
+ */
- .macro addruart, rp, rv, tmp
- ldr \rp, =IO_APB_PHYS @ physical
- ldr \rv, =IO_APB_VIRT @ virtual
- orr \rp, \rp, #(TEGRA_DEBUG_UART_BASE & 0xFF)
- orr \rp, \rp, #(TEGRA_DEBUG_UART_BASE & 0xFF00)
- orr \rv, \rv, #(TEGRA_DEBUG_UART_BASE & 0xFF)
- orr \rv, \rv, #(TEGRA_DEBUG_UART_BASE & 0xFF00)
- .endm
+ .macro senduart, rd, rx
+ tst \rx, #0x0000ff00
+ strneb \rd, [\rx, #UART_TX << UART_SHIFT]
+1001:
+ .endm
-#define UART_SHIFT 2
-#include <asm/hardware/debug-8250.S>
+ .macro busyuart, rd, rx
+ tst \rx, #0x0000ff00
+ beq 1002f
+1001: ldrb \rd, [\rx, #UART_LSR << UART_SHIFT]
+ and \rd, \rd, #UART_LSR_TEMT | UART_LSR_THRE
+ teq \rd, #UART_LSR_TEMT | UART_LSR_THRE
+ bne 1001b
+1002:
+ .endm
+ .macro waituart, rd, rx
+#ifdef FLOW_CONTROL
+ tst \rx, #0x0000ff00
+ beq 1002f
+1001: ldrb \rd, [\rx, #UART_MSR << UART_SHIFT]
+ tst \rd, #UART_MSR_CTS
+ beq 1001b
+1002:
+#endif
+ .endm
diff --git a/arch/arm/mach-tegra/include/mach/gpio-tegra.h b/arch/arm/mach-tegra/include/mach/gpio-tegra.h
index 87d37fdf50846ef6d3baa66dd31e5e4b278babfa..6140820555e1a88ffbc058e6ae22a49e73ef0635 100644
--- a/arch/arm/mach-tegra/include/mach/gpio-tegra.h
+++ b/arch/arm/mach-tegra/include/mach/gpio-tegra.h
@@ -25,8 +25,6 @@
#define TEGRA_NR_GPIOS INT_GPIO_NR
-#define TEGRA_GPIO_TO_IRQ(gpio) (INT_GPIO_BASE + (gpio))
-
struct tegra_gpio_table {
int gpio; /* GPIO number */
bool enable; /* Enable for GPIO at init? */
diff --git a/arch/arm/mach-tegra/include/mach/irammap.h b/arch/arm/mach-tegra/include/mach/irammap.h
new file mode 100644
index 0000000000000000000000000000000000000000..0cbe63261854b644a57e2d6a8f35c23ce9511c0a
--- /dev/null
+++ b/arch/arm/mach-tegra/include/mach/irammap.h
@@ -0,0 +1,35 @@
+/*
+ * Copyright (c) 2012, NVIDIA CORPORATION. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __MACH_TEGRA_IRAMMAP_H
+#define __MACH_TEGRA_IRAMMAP_H
+
+#include <asm/sizes.h>
+
+/* The first 1K of IRAM is permanently reserved for the CPU reset handler */
+#define TEGRA_IRAM_RESET_HANDLER_OFFSET 0
+#define TEGRA_IRAM_RESET_HANDLER_SIZE SZ_1K
+
+/*
+ * These locations are written to by uncompress.h, and read by debug-macro.S.
+ * The first word holds the cookie value if the data is valid. The second
+ * word holds the UART physical address.
+ */
+#define TEGRA_IRAM_DEBUG_UART_OFFSET SZ_1K
+#define TEGRA_IRAM_DEBUG_UART_SIZE 8
+#define TEGRA_IRAM_DEBUG_UART_COOKIE 0x55415254
+
+#endif
diff --git a/arch/arm/mach-tegra/include/mach/uncompress.h b/arch/arm/mach-tegra/include/mach/uncompress.h
index 4e8323770c79770b21f24f9dc1228a0186973a3c..5a440f315e575d29c43958fd1c84226843056447 100644
--- a/arch/arm/mach-tegra/include/mach/uncompress.h
+++ b/arch/arm/mach-tegra/include/mach/uncompress.h
@@ -2,10 +2,14 @@
* arch/arm/mach-tegra/include/mach/uncompress.h
*
* Copyright (C) 2010 Google, Inc.
+ * Copyright (C) 2011 Google, Inc.
+ * Copyright (C) 2011-2012 NVIDIA CORPORATION. All Rights Reserved.
*
* Author:
* Colin Cross <ccross@google.com>
* Erik Gilling <konkers@google.com>
+ * Doug Anderson <dianders@chromium.org>
+ * Stephen Warren <swarren@nvidia.com>
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
@@ -25,36 +29,130 @@
#include <linux/serial_reg.h>
#include <mach/iomap.h>
+#include <mach/irammap.h>
+
+#define BIT(x) (1 << (x))
+#define ARRAY_SIZE(arr) (sizeof(arr) / sizeof((arr)[0]))
+
+#define DEBUG_UART_SHIFT 2
+
+volatile u8 *uart;
static void putc(int c)
{
- volatile u8 *uart = (volatile u8 *)TEGRA_DEBUG_UART_BASE;
- int shift = 2;
-
if (uart == NULL)
return;
- while (!(uart[UART_LSR << shift] & UART_LSR_THRE))
+ while (!(uart[UART_LSR << DEBUG_UART_SHIFT] & UART_LSR_THRE))
barrier();
- uart[UART_TX << shift] = c;
+ uart[UART_TX << DEBUG_UART_SHIFT] = c;
}
static inline void flush(void)
{
}
+static inline void save_uart_address(void)
+{
+ u32 *buf = (u32 *)(TEGRA_IRAM_BASE + TEGRA_IRAM_DEBUG_UART_OFFSET);
+
+ if (uart) {
+ buf[0] = TEGRA_IRAM_DEBUG_UART_COOKIE;
+ buf[1] = (u32)uart;
+ } else
+ buf[0] = 0;
+}
+
+/*
+ * Setup before decompression. This is where we do UART selection for
+ * earlyprintk and init the uart_base register.
+ */
static inline void arch_decomp_setup(void)
{
- volatile u8 *uart = (volatile u8 *)TEGRA_DEBUG_UART_BASE;
- int shift = 2;
+ static const struct {
+ u32 base;
+ u32 reset_reg;
+ u32 clock_reg;
+ u32 bit;
+ } uarts[] = {
+ {
+ TEGRA_UARTA_BASE,
+ TEGRA_CLK_RESET_BASE + 0x04,
+ TEGRA_CLK_RESET_BASE + 0x10,
+ 6,
+ },
+ {
+ TEGRA_UARTB_BASE,
+ TEGRA_CLK_RESET_BASE + 0x04,
+ TEGRA_CLK_RESET_BASE + 0x10,
+ 7,
+ },
+ {
+ TEGRA_UARTC_BASE,
+ TEGRA_CLK_RESET_BASE + 0x08,
+ TEGRA_CLK_RESET_BASE + 0x14,
+ 23,
+ },
+ {
+ TEGRA_UARTD_BASE,
+ TEGRA_CLK_RESET_BASE + 0x0c,
+ TEGRA_CLK_RESET_BASE + 0x18,
+ 1,
+ },
+ {
+ TEGRA_UARTE_BASE,
+ TEGRA_CLK_RESET_BASE + 0x0c,
+ TEGRA_CLK_RESET_BASE + 0x18,
+ 2,
+ },
+ };
+ int i;
+ volatile u32 *apb_misc = (volatile u32 *)TEGRA_APB_MISC_BASE;
+ u32 chip, div;
+
+ /*
+ * Look for the first UART that:
+ * a) Is not in reset.
+ * b) Is clocked.
+ * c) Has a 'D' in the scratchpad register.
+ *
+ * Note that on Tegra30, the first two conditions are required, since
+ * if not true, accesses to the UART scratch register will hang.
+ * Tegra20 doesn't have this issue.
+ *
+ * The intent is that the bootloader will tell the kernel which UART
+ * to use by setting up those conditions. If nothing found, we'll fall
+ * back to what's specified in TEGRA_DEBUG_UART_BASE.
+ */
+ for (i = 0; i < ARRAY_SIZE(uarts); i++) {
+ if (*(u8 *)uarts[i].reset_reg & BIT(uarts[i].bit))
+ continue;
+ if (!(*(u8 *)uarts[i].clock_reg & BIT(uarts[i].bit)))
+ continue;
+
+ uart = (volatile u8 *)uarts[i].base;
+ if (uart[UART_SCR << DEBUG_UART_SHIFT] != 'D')
+ continue;
+
+ break;
+ }
+ if (i == ARRAY_SIZE(uarts))
+ uart = (volatile u8 *)TEGRA_DEBUG_UART_BASE;
+ save_uart_address();
if (uart == NULL)
return;
- uart[UART_LCR << shift] |= UART_LCR_DLAB;
- uart[UART_DLL << shift] = 0x75;
- uart[UART_DLM << shift] = 0x0;
- uart[UART_LCR << shift] = 3;
+ chip = (apb_misc[0x804 / 4] >> 8) & 0xff;
+ if (chip == 0x20)
+ div = 0x0075;
+ else
+ div = 0x00dd;
+
+ uart[UART_LCR << DEBUG_UART_SHIFT] |= UART_LCR_DLAB;
+ uart[UART_DLL << DEBUG_UART_SHIFT] = div & 0xff;
+ uart[UART_DLM << DEBUG_UART_SHIFT] = div >> 8;
+ uart[UART_LCR << DEBUG_UART_SHIFT] = 3;
}
static inline void arch_decomp_wdog(void)
diff --git a/arch/arm/mach-tegra/pmc.c b/arch/arm/mach-tegra/pmc.c
new file mode 100644
index 0000000000000000000000000000000000000000..7af6a54404be53818c8f02af3e37c4b1b648e7bb
--- /dev/null
+++ b/arch/arm/mach-tegra/pmc.c
@@ -0,0 +1,76 @@
+/*
+ * Copyright (C) 2012 NVIDIA CORPORATION. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <linux/of.h>
+
+#include <mach/iomap.h>
+
+#define PMC_CTRL 0x0
+#define PMC_CTRL_INTR_LOW (1 << 17)
+
+static inline u32 tegra_pmc_readl(u32 reg)
+{
+ return readl(IO_ADDRESS(TEGRA_PMC_BASE + reg));
+}
+
+static inline void tegra_pmc_writel(u32 val, u32 reg)
+{
+ writel(val, IO_ADDRESS(TEGRA_PMC_BASE + reg));
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id matches[] __initconst = {
+ { .compatible = "nvidia,tegra20-pmc" },
+ { }
+};
+#endif
+
+void __init tegra_pmc_init(void)
+{
+ /*
+ * For now, Harmony is the only board that uses the PMC, and it wants
+ * the signal inverted. Seaboard would too if it used the PMC.
+ * Hopefully by the time other boards want to use the PMC, everything
+ * will be device-tree, or they also want it inverted.
+ */
+ bool invert_interrupt = true;
+ u32 val;
+
+#ifdef CONFIG_OF
+ if (of_have_populated_dt()) {
+ struct device_node *np;
+
+ invert_interrupt = false;
+
+ np = of_find_matching_node(NULL, matches);
+ if (np) {
+ if (of_find_property(np, "nvidia,invert-interrupt",
+ NULL))
+ invert_interrupt = true;
+ }
+ }
+#endif
+
+ val = tegra_pmc_readl(PMC_CTRL);
+ if (invert_interrupt)
+ val |= PMC_CTRL_INTR_LOW;
+ else
+ val &= ~PMC_CTRL_INTR_LOW;
+ tegra_pmc_writel(val, PMC_CTRL);
+}
diff --git a/arch/arm/mach-tegra/pmc.h b/arch/arm/mach-tegra/pmc.h
new file mode 100644
index 0000000000000000000000000000000000000000..8995ee4a87681dd80a63c990b05c324955261f24
--- /dev/null
+++ b/arch/arm/mach-tegra/pmc.h
@@ -0,0 +1,23 @@
+/*
+ * Copyright (C) 2012 NVIDIA CORPORATION. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+#ifndef __MACH_TEGRA_PMC_H
+#define __MACH_TEGRA_PMC_H
+
+void tegra_pmc_init(void);
+
+#endif
diff --git a/arch/arm/mach-tegra/tegra2_clocks.c b/arch/arm/mach-tegra/tegra2_clocks.c
index 1976e934cdd923b76d343f3941b3f39c1d65c290..592a4eeb5328c6fa70f29dde7f53ba530995c488 100644
--- a/arch/arm/mach-tegra/tegra2_clocks.c
+++ b/arch/arm/mach-tegra/tegra2_clocks.c
@@ -720,7 +720,7 @@ static void tegra2_pllx_clk_init(struct clk *c)
{
tegra2_pll_clk_init(c);
- if (tegra_sku_id() == 7)
+ if (tegra_sku_id == 7)
c->max_rate = 750000000;
}
diff --git a/arch/arm/mach-tegra/tegra2_emc.c b/arch/arm/mach-tegra/tegra2_emc.c
index 0f7ae6e90b5590c43d1e4c6f3de4ab8ffeda40aa..5070d833bdd1ebbf3df1763353f155e66b97d04a 100644
--- a/arch/arm/mach-tegra/tegra2_emc.c
+++ b/arch/arm/mach-tegra/tegra2_emc.c
@@ -16,14 +16,19 @@
*/
#include <linux/kernel.h>
+#include <linux/device.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/tegra_emc.h>
#include <mach/iomap.h>
#include "tegra2_emc.h"
+#include "fuse.h"
#ifdef CONFIG_TEGRA_EMC_SCALING_ENABLE
static bool emc_enable = true;
@@ -32,18 +37,17 @@ static bool emc_enable;
#endif
module_param(emc_enable, bool, 0644);
-static void __iomem *emc = IO_ADDRESS(TEGRA_EMC_BASE);
-static const struct tegra_emc_table *tegra_emc_table;
-static int tegra_emc_table_size;
+static struct platform_device *emc_pdev;
+static void __iomem *emc_regbase;
static inline void emc_writel(u32 val, unsigned long addr)
{
- writel(val, emc + addr);
+ writel(val, emc_regbase + addr);
}
static inline u32 emc_readl(unsigned long addr)
{
- return readl(emc + addr);
+ return readl(emc_regbase + addr);
}
static const unsigned long emc_reg_addr[TEGRA_EMC_NUM_REGS] = {
@@ -98,15 +102,15 @@ static const unsigned long emc_reg_addr[TEGRA_EMC_NUM_REGS] = {
/* Select the closest EMC rate that is higher than the requested rate */
long tegra_emc_round_rate(unsigned long rate)
{
+ struct tegra_emc_pdata *pdata;
int i;
int best = -1;
unsigned long distance = ULONG_MAX;
- if (!tegra_emc_table)
+ if (!emc_pdev)
return -EINVAL;
- if (!emc_enable)
- return -EINVAL;
+ pdata = emc_pdev->dev.platform_data;
pr_debug("%s: %lu\n", __func__, rate);
@@ -116,10 +120,10 @@ long tegra_emc_round_rate(unsigned long rate)
*/
rate = rate / 2 / 1000;
- for (i = 0; i < tegra_emc_table_size; i++) {
- if (tegra_emc_table[i].rate >= rate &&
- (tegra_emc_table[i].rate - rate) < distance) {
- distance = tegra_emc_table[i].rate - rate;
+ for (i = 0; i < pdata->num_tables; i++) {
+ if (pdata->tables[i].rate >= rate &&
+ (pdata->tables[i].rate - rate) < distance) {
+ distance = pdata->tables[i].rate - rate;
best = i;
}
}
@@ -127,9 +131,9 @@ long tegra_emc_round_rate(unsigned long rate)
if (best < 0)
return -EINVAL;
- pr_debug("%s: using %lu\n", __func__, tegra_emc_table[best].rate);
+ pr_debug("%s: using %lu\n", __func__, pdata->tables[best].rate);
- return tegra_emc_table[best].rate * 2 * 1000;
+ return pdata->tables[best].rate * 2 * 1000;
}
/*
@@ -142,37 +146,211 @@ long tegra_emc_round_rate(unsigned long rate)
*/
int tegra_emc_set_rate(unsigned long rate)
{
+ struct tegra_emc_pdata *pdata;
int i;
int j;
- if (!tegra_emc_table)
+ if (!emc_pdev)
return -EINVAL;
+ pdata = emc_pdev->dev.platform_data;
+
/*
* The EMC clock rate is twice the bus rate, and the bus rate is
* measured in kHz
*/
rate = rate / 2 / 1000;
- for (i = 0; i < tegra_emc_table_size; i++)
- if (tegra_emc_table[i].rate == rate)
+ for (i = 0; i < pdata->num_tables; i++)
+ if (pdata->tables[i].rate == rate)
break;
- if (i >= tegra_emc_table_size)
+ if (i >= pdata->num_tables)
return -EINVAL;
pr_debug("%s: setting to %lu\n", __func__, rate);
for (j = 0; j < TEGRA_EMC_NUM_REGS; j++)
- emc_writel(tegra_emc_table[i].regs[j], emc_reg_addr[j]);
+ emc_writel(pdata->tables[i].regs[j], emc_reg_addr[j]);
- emc_readl(tegra_emc_table[i].regs[TEGRA_EMC_NUM_REGS - 1]);
+ emc_readl(pdata->tables[i].regs[TEGRA_EMC_NUM_REGS - 1]);
return 0;
}
-void tegra_init_emc(const struct tegra_emc_table *table, int table_size)
+#ifdef CONFIG_OF
+static struct device_node *tegra_emc_ramcode_devnode(struct device_node *np)
+{
+ struct device_node *iter;
+ u32 reg;
+
+ for_each_child_of_node(np, iter) {
+ if (of_property_read_u32(np, "nvidia,ram-code", ®))
+ continue;
+ if (reg == tegra_bct_strapping)
+ return of_node_get(iter);
+ }
+
+ return NULL;
+}
+
+static struct tegra_emc_pdata *tegra_emc_dt_parse_pdata(
+ struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *tnp, *iter;
+ struct tegra_emc_pdata *pdata;
+ int ret, i, num_tables;
+
+ if (!np)
+ return NULL;
+
+ if (of_find_property(np, "nvidia,use-ram-code", NULL)) {
+ tnp = tegra_emc_ramcode_devnode(np);
+ if (!tnp)
+ dev_warn(&pdev->dev,
+ "can't find emc table for ram-code 0x%02x\n",
+ tegra_bct_strapping);
+ } else
+ tnp = of_node_get(np);
+
+ if (!tnp)
+ return NULL;
+
+ num_tables = 0;
+ for_each_child_of_node(tnp, iter)
+ if (of_device_is_compatible(iter, "nvidia,tegra20-emc-table"))
+ num_tables++;
+
+ if (!num_tables) {
+ pdata = NULL;
+ goto out;
+ }
+
+ pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+ pdata->tables = devm_kzalloc(&pdev->dev,
+ sizeof(*pdata->tables) * num_tables,
+ GFP_KERNEL);
+
+ i = 0;
+ for_each_child_of_node(tnp, iter) {
+ u32 prop;
+
+ ret = of_property_read_u32(iter, "clock-frequency", &prop);
+ if (ret) {
+ dev_err(&pdev->dev, "no clock-frequency in %s\n",
+ iter->full_name);
+ continue;
+ }
+ pdata->tables[i].rate = prop;
+
+ ret = of_property_read_u32_array(iter, "nvidia,emc-registers",
+ pdata->tables[i].regs,
+ TEGRA_EMC_NUM_REGS);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "malformed emc-registers property in %s\n",
+ iter->full_name);
+ continue;
+ }
+
+ i++;
+ }
+ pdata->num_tables = i;
+
+out:
+ of_node_put(tnp);
+ return pdata;
+}
+#else
+static struct tegra_emc_pdata *tegra_emc_dt_parse_pdata(
+ struct platform_device *pdev)
+{
+ return NULL;
+}
+#endif
+
+static struct tegra_emc_pdata __devinit *tegra_emc_fill_pdata(struct platform_device *pdev)
+{
+ struct clk *c = clk_get_sys(NULL, "emc");
+ struct tegra_emc_pdata *pdata;
+ unsigned long khz;
+ int i;
+
+ WARN_ON(pdev->dev.platform_data);
+ BUG_ON(IS_ERR_OR_NULL(c));
+
+ pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+ pdata->tables = devm_kzalloc(&pdev->dev, sizeof(*pdata->tables),
+ GFP_KERNEL);
+
+ pdata->tables[0].rate = clk_get_rate(c) / 2 / 1000;
+
+ for (i = 0; i < TEGRA_EMC_NUM_REGS; i++)
+ pdata->tables[0].regs[i] = emc_readl(emc_reg_addr[i]);
+
+ pdata->num_tables = 1;
+
+ khz = pdata->tables[0].rate;
+ dev_info(&pdev->dev, "no tables provided, using %ld kHz emc, "
+ "%ld kHz mem\n", khz * 2, khz);
+
+ return pdata;
+}
+
+static int __devinit tegra_emc_probe(struct platform_device *pdev)
+{
+ struct tegra_emc_pdata *pdata;
+ struct resource *res;
+
+ if (!emc_enable) {
+ dev_err(&pdev->dev, "disabled per module parameter\n");
+ return -ENODEV;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "missing register base\n");
+ return -ENOMEM;
+ }
+
+ emc_regbase = devm_request_and_ioremap(&pdev->dev, res);
+ if (!emc_regbase) {
+ dev_err(&pdev->dev, "failed to remap registers\n");
+ return -ENOMEM;
+ }
+
+ pdata = pdev->dev.platform_data;
+
+ if (!pdata)
+ pdata = tegra_emc_dt_parse_pdata(pdev);
+
+ if (!pdata)
+ pdata = tegra_emc_fill_pdata(pdev);
+
+ pdev->dev.platform_data = pdata;
+
+ emc_pdev = pdev;
+
+ return 0;
+}
+
+static struct of_device_id tegra_emc_of_match[] __devinitdata = {
+ { .compatible = "nvidia,tegra20-emc", },
+ { },
+};
+
+static struct platform_driver tegra_emc_driver = {
+ .driver = {
+ .name = "tegra-emc",
+ .owner = THIS_MODULE,
+ .of_match_table = tegra_emc_of_match,
+ },
+ .probe = tegra_emc_probe,
+};
+
+static int __init tegra_emc_init(void)
{
- tegra_emc_table = table;
- tegra_emc_table_size = table_size;
+ return platform_driver_register(&tegra_emc_driver);
}
+device_initcall(tegra_emc_init);
diff --git a/arch/arm/mach-tegra/tegra2_emc.h b/arch/arm/mach-tegra/tegra2_emc.h
index 19f08cb3160383e3a19f4cb9ce430536d6099750..f61409b54cb7084b956caa37def09c3f04083884 100644
--- a/arch/arm/mach-tegra/tegra2_emc.h
+++ b/arch/arm/mach-tegra/tegra2_emc.h
@@ -15,13 +15,10 @@
*
*/
-#define TEGRA_EMC_NUM_REGS 46
-
-struct tegra_emc_table {
- unsigned long rate;
- u32 regs[TEGRA_EMC_NUM_REGS];
-};
+#ifndef __MACH_TEGRA_TEGRA2_EMC_H_
+#define __MACH_TEGRA_TEGRA2_EMC_H
int tegra_emc_set_rate(unsigned long rate);
long tegra_emc_round_rate(unsigned long rate);
-void tegra_init_emc(const struct tegra_emc_table *table, int table_size);
+
+#endif
diff --git a/arch/arm/plat-mxc/devices/platform-ahci-imx.c b/arch/arm/plat-mxc/devices/platform-ahci-imx.c
index d8a56aee521b3281ca9b3f62fea52e624973b804..ade4a1c4e2a39e4aac13479deb48af97fd142c0b 100644
--- a/arch/arm/plat-mxc/devices/platform-ahci-imx.c
+++ b/arch/arm/plat-mxc/devices/platform-ahci-imx.c
@@ -60,9 +60,9 @@ static int imx_sata_init(struct device *dev, void __iomem *addr)
dev_err(dev, "no sata clock.\n");
return PTR_ERR(sata_clk);
}
- ret = clk_enable(sata_clk);
+ ret = clk_prepare_enable(sata_clk);
if (ret) {
- dev_err(dev, "can't enable sata clock.\n");
+ dev_err(dev, "can't prepare/enable sata clock.\n");
goto put_sata_clk;
}
@@ -73,9 +73,9 @@ static int imx_sata_init(struct device *dev, void __iomem *addr)
ret = PTR_ERR(sata_ref_clk);
goto release_sata_clk;
}
- ret = clk_enable(sata_ref_clk);
+ ret = clk_prepare_enable(sata_ref_clk);
if (ret) {
- dev_err(dev, "can't enable sata ref clock.\n");
+ dev_err(dev, "can't prepare/enable sata ref clock.\n");
goto put_sata_ref_clk;
}
@@ -104,11 +104,11 @@ static int imx_sata_init(struct device *dev, void __iomem *addr)
return 0;
release_sata_ref_clk:
- clk_disable(sata_ref_clk);
+ clk_disable_unprepare(sata_ref_clk);
put_sata_ref_clk:
clk_put(sata_ref_clk);
release_sata_clk:
- clk_disable(sata_clk);
+ clk_disable_unprepare(sata_clk);
put_sata_clk:
clk_put(sata_clk);
@@ -117,10 +117,10 @@ static int imx_sata_init(struct device *dev, void __iomem *addr)
static void imx_sata_exit(struct device *dev)
{
- clk_disable(sata_ref_clk);
+ clk_disable_unprepare(sata_ref_clk);
clk_put(sata_ref_clk);
- clk_disable(sata_clk);
+ clk_disable_unprepare(sata_clk);
clk_put(sata_clk);
}
diff --git a/arch/arm/plat-mxc/epit.c b/arch/arm/plat-mxc/epit.c
index d3467f818c3397188075801d13343863182707ee..9129c9e7d532b2a08f2f464e489aeabad5f1badf 100644
--- a/arch/arm/plat-mxc/epit.c
+++ b/arch/arm/plat-mxc/epit.c
@@ -203,7 +203,7 @@ static int __init epit_clockevent_init(struct clk *timer_clk)
void __init epit_timer_init(struct clk *timer_clk, void __iomem *base, int irq)
{
- clk_enable(timer_clk);
+ clk_prepare_enable(timer_clk);
timer_base = base;
diff --git a/arch/arm/plat-mxc/include/mach/board-mx31ads.h b/arch/arm/plat-mxc/include/mach/board-mx31ads.h
deleted file mode 100644
index 94b60dd47137815546daa21dda6fde02a403b055..0000000000000000000000000000000000000000
--- a/arch/arm/plat-mxc/include/mach/board-mx31ads.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-/*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_MX31ADS_H__
-#define __ASM_ARCH_MXC_BOARD_MX31ADS_H__
-
-#include <mach/hardware.h>
-
-/*
- * These symbols are used by drivers/net/cs89x0.c.
- * This is ugly as hell, but we have to provide them until
- * someone fixed the driver.
- */
-
-/* Base address of PBC controller */
-#define PBC_BASE_ADDRESS MX31_CS4_BASE_ADDR_VIRT
-/* Offsets for the PBC Controller register */
-
-/* Ethernet Controller IO base address */
-#define PBC_CS8900A_IOBASE 0x020000
-
-#define MXC_EXP_IO_BASE (MXC_BOARD_IRQ_START)
-
-#define EXPIO_INT_ENET_INT (MXC_EXP_IO_BASE + 8)
-
-#endif /* __ASM_ARCH_MXC_BOARD_MX31ADS_H__ */
diff --git a/arch/arm/plat-mxc/include/mach/debug-macro.S b/arch/arm/plat-mxc/include/mach/debug-macro.S
index 6e192c4a391a2af315ab3ae6f73a6603b49040cc..8ddda365f1a0c3637b73e456312740dd3de13126 100644
--- a/arch/arm/plat-mxc/include/mach/debug-macro.S
+++ b/arch/arm/plat-mxc/include/mach/debug-macro.S
@@ -24,7 +24,7 @@
#define UART_PADDR MX51_UART1_BASE_ADDR
#elif defined (CONFIG_DEBUG_IMX50_IMX53_UART)
#define UART_PADDR MX53_UART1_BASE_ADDR
-#elif defined (CONFIG_DEBUG_IMX6Q_UART)
+#elif defined (CONFIG_DEBUG_IMX6Q_UART4)
#define UART_PADDR MX6Q_UART4_BASE_ADDR
#endif
diff --git a/arch/arm/plat-mxc/include/mach/dma.h b/arch/arm/plat-mxc/include/mach/dma.h
index 233d0a5e2d68f1451b29ce18e331a384fabaf5a5..1b9080385b4618b2b3c76ab057a7bf271df8d73d 100644
--- a/arch/arm/plat-mxc/include/mach/dma.h
+++ b/arch/arm/plat-mxc/include/mach/dma.h
@@ -60,8 +60,7 @@ static inline int imx_dma_is_ipu(struct dma_chan *chan)
static inline int imx_dma_is_general_purpose(struct dma_chan *chan)
{
- return !strcmp(dev_name(chan->device->dev), "imx31-sdma") ||
- !strcmp(dev_name(chan->device->dev), "imx35-sdma") ||
+ return strstr(dev_name(chan->device->dev), "sdma") ||
!strcmp(dev_name(chan->device->dev), "imx-dma");
}
diff --git a/arch/arm/plat-mxc/pwm.c b/arch/arm/plat-mxc/pwm.c
index e032717f7d02c211ee8cad0d0200cec5f83974cf..c0cab2270dd171f64b713fb5b3a1700fb298900c 100644
--- a/arch/arm/plat-mxc/pwm.c
+++ b/arch/arm/plat-mxc/pwm.c
@@ -132,7 +132,7 @@ int pwm_enable(struct pwm_device *pwm)
int rc = 0;
if (!pwm->clk_enabled) {
- rc = clk_enable(pwm->clk);
+ rc = clk_prepare_enable(pwm->clk);
if (!rc)
pwm->clk_enabled = 1;
}
@@ -145,7 +145,7 @@ void pwm_disable(struct pwm_device *pwm)
writel(0, pwm->mmio_base + MX3_PWMCR);
if (pwm->clk_enabled) {
- clk_disable(pwm->clk);
+ clk_disable_unprepare(pwm->clk);
pwm->clk_enabled = 0;
}
}
diff --git a/arch/arm/plat-mxc/system.c b/arch/arm/plat-mxc/system.c
index 3599bf2cfd4f7a351717bb3abdd2f54160d4d712..f30dcacbbd0aef44b68a26cbd82563b7b8320a8e 100644
--- a/arch/arm/plat-mxc/system.c
+++ b/arch/arm/plat-mxc/system.c
@@ -48,7 +48,7 @@ void mxc_restart(char mode, const char *cmd)
clk = clk_get_sys("imx2-wdt.0", NULL);
if (!IS_ERR(clk))
- clk_enable(clk);
+ clk_prepare_enable(clk);
wcr_enable = (1 << 2);
}
diff --git a/arch/arm/plat-mxc/time.c b/arch/arm/plat-mxc/time.c
index 1c96cdb4c35e9036ff78e97a084a1423a720e1ca..7daf7c9a413bf62eb9a7ad86f659a0eadf016d44 100644
--- a/arch/arm/plat-mxc/time.c
+++ b/arch/arm/plat-mxc/time.c
@@ -283,7 +283,7 @@ void __init mxc_timer_init(struct clk *timer_clk, void __iomem *base, int irq)
{
uint32_t tctl_val;
- clk_enable(timer_clk);
+ clk_prepare_enable(timer_clk);
timer_base = base;
diff --git a/arch/arm/plat-omap/include/plat/omap_hwmod.h b/arch/arm/plat-omap/include/plat/omap_hwmod.h
index 647010109afabd4d373ae96c357bf9f990ef3ccd..9e8e63d52aab9515a67882c534c7b563e29bbe9a 100644
--- a/arch/arm/plat-omap/include/plat/omap_hwmod.h
+++ b/arch/arm/plat-omap/include/plat/omap_hwmod.h
@@ -484,7 +484,6 @@ struct omap_hwmod_class {
* @main_clk: main clock: OMAP clock name
* @_clk: pointer to the main struct clk (filled in at runtime)
* @opt_clks: other device clocks that drivers can request (0..*)
- * @vdd_name: voltage domain name
* @voltdm: pointer to voltage domain (filled in at runtime)
* @masters: ptr to array of OCP ifs that this hwmod can initiate on
* @slaves: ptr to array of OCP ifs that this hwmod can respond on
@@ -528,7 +527,6 @@ struct omap_hwmod {
struct omap_hwmod_opt_clk *opt_clks;
char *clkdm_name;
struct clockdomain *clkdm;
- char *vdd_name;
struct omap_hwmod_ocp_if **masters; /* connect to *_IA */
struct omap_hwmod_ocp_if **slaves; /* connect to *_TA */
void *dev_attr;
diff --git a/arch/arm/plat-samsung/include/plat/dma-pl330.h b/arch/arm/plat-samsung/include/plat/dma-pl330.h
index c5eaad529de57d4dbdf94a2fdb96bef820ae70fd..0670f37aaaedcfe7990d359df010db7ced9c935a 100644
--- a/arch/arm/plat-samsung/include/plat/dma-pl330.h
+++ b/arch/arm/plat-samsung/include/plat/dma-pl330.h
@@ -82,6 +82,22 @@ enum dma_ch {
DMACH_SLIMBUS4_TX,
DMACH_SLIMBUS5_RX,
DMACH_SLIMBUS5_TX,
+ DMACH_MIPI_HSI0,
+ DMACH_MIPI_HSI1,
+ DMACH_MIPI_HSI2,
+ DMACH_MIPI_HSI3,
+ DMACH_MIPI_HSI4,
+ DMACH_MIPI_HSI5,
+ DMACH_MIPI_HSI6,
+ DMACH_MIPI_HSI7,
+ DMACH_MTOM_0,
+ DMACH_MTOM_1,
+ DMACH_MTOM_2,
+ DMACH_MTOM_3,
+ DMACH_MTOM_4,
+ DMACH_MTOM_5,
+ DMACH_MTOM_6,
+ DMACH_MTOM_7,
/* END Marker, also used to denote a reserved channel */
DMACH_MAX,
};
diff --git a/arch/arm/plat-samsung/include/plat/regs-rtc.h b/arch/arm/plat-samsung/include/plat/regs-rtc.h
index 30b7cc14cef5b6acd81edc534930ba4f11726fb7..0f8263e93eea94678b28f8e8d60cbbc1f6a48763 100644
--- a/arch/arm/plat-samsung/include/plat/regs-rtc.h
+++ b/arch/arm/plat-samsung/include/plat/regs-rtc.h
@@ -18,51 +18,54 @@
#define S3C2410_INTP_ALM (1 << 1)
#define S3C2410_INTP_TIC (1 << 0)
-#define S3C2410_RTCCON S3C2410_RTCREG(0x40)
-#define S3C2410_RTCCON_RTCEN (1<<0)
-#define S3C2410_RTCCON_CLKSEL (1<<1)
-#define S3C2410_RTCCON_CNTSEL (1<<2)
-#define S3C2410_RTCCON_CLKRST (1<<3)
-#define S3C64XX_RTCCON_TICEN (1<<8)
+#define S3C2410_RTCCON S3C2410_RTCREG(0x40)
+#define S3C2410_RTCCON_RTCEN (1 << 0)
+#define S3C2410_RTCCON_CNTSEL (1 << 2)
+#define S3C2410_RTCCON_CLKRST (1 << 3)
+#define S3C2443_RTCCON_TICSEL (1 << 4)
+#define S3C64XX_RTCCON_TICEN (1 << 8)
-#define S3C64XX_RTCCON_TICMSK (0xF<<7)
-#define S3C64XX_RTCCON_TICSHT (7)
+#define S3C2410_TICNT S3C2410_RTCREG(0x44)
+#define S3C2410_TICNT_ENABLE (1 << 7)
-#define S3C2410_TICNT S3C2410_RTCREG(0x44)
-#define S3C2410_TICNT_ENABLE (1<<7)
+/* S3C2443: tick count is 15 bit wide
+ * TICNT[6:0] contains upper 7 bits
+ * TICNT1[7:0] contains lower 8 bits
+ */
+#define S3C2443_TICNT_PART(x) ((x & 0x7f00) >> 8)
+#define S3C2443_TICNT1 S3C2410_RTCREG(0x4C)
+#define S3C2443_TICNT1_PART(x) (x & 0xff)
-#define S3C2410_RTCALM S3C2410_RTCREG(0x50)
-#define S3C2410_RTCALM_ALMEN (1<<6)
-#define S3C2410_RTCALM_YEAREN (1<<5)
-#define S3C2410_RTCALM_MONEN (1<<4)
-#define S3C2410_RTCALM_DAYEN (1<<3)
-#define S3C2410_RTCALM_HOUREN (1<<2)
-#define S3C2410_RTCALM_MINEN (1<<1)
-#define S3C2410_RTCALM_SECEN (1<<0)
+/* S3C2416: tick count is 32 bit wide
+ * TICNT[6:0] contains bits [14:8]
+ * TICNT1[7:0] contains lower 8 bits
+ * TICNT2[16:0] contains upper 17 bits
+ */
+#define S3C2416_TICNT2 S3C2410_RTCREG(0x48)
+#define S3C2416_TICNT2_PART(x) ((x & 0xffff8000) >> 15)
-#define S3C2410_RTCALM_ALL \
- S3C2410_RTCALM_ALMEN | S3C2410_RTCALM_YEAREN | S3C2410_RTCALM_MONEN |\
- S3C2410_RTCALM_DAYEN | S3C2410_RTCALM_HOUREN | S3C2410_RTCALM_MINEN |\
- S3C2410_RTCALM_SECEN
+#define S3C2410_RTCALM S3C2410_RTCREG(0x50)
+#define S3C2410_RTCALM_ALMEN (1 << 6)
+#define S3C2410_RTCALM_YEAREN (1 << 5)
+#define S3C2410_RTCALM_MONEN (1 << 4)
+#define S3C2410_RTCALM_DAYEN (1 << 3)
+#define S3C2410_RTCALM_HOUREN (1 << 2)
+#define S3C2410_RTCALM_MINEN (1 << 1)
+#define S3C2410_RTCALM_SECEN (1 << 0)
+#define S3C2410_ALMSEC S3C2410_RTCREG(0x54)
+#define S3C2410_ALMMIN S3C2410_RTCREG(0x58)
+#define S3C2410_ALMHOUR S3C2410_RTCREG(0x5c)
-#define S3C2410_ALMSEC S3C2410_RTCREG(0x54)
-#define S3C2410_ALMMIN S3C2410_RTCREG(0x58)
-#define S3C2410_ALMHOUR S3C2410_RTCREG(0x5c)
-
-#define S3C2410_ALMDATE S3C2410_RTCREG(0x60)
-#define S3C2410_ALMMON S3C2410_RTCREG(0x64)
-#define S3C2410_ALMYEAR S3C2410_RTCREG(0x68)
-
-#define S3C2410_RTCRST S3C2410_RTCREG(0x6c)
-
-#define S3C2410_RTCSEC S3C2410_RTCREG(0x70)
-#define S3C2410_RTCMIN S3C2410_RTCREG(0x74)
-#define S3C2410_RTCHOUR S3C2410_RTCREG(0x78)
-#define S3C2410_RTCDATE S3C2410_RTCREG(0x7c)
-#define S3C2410_RTCDAY S3C2410_RTCREG(0x80)
-#define S3C2410_RTCMON S3C2410_RTCREG(0x84)
-#define S3C2410_RTCYEAR S3C2410_RTCREG(0x88)
+#define S3C2410_ALMDATE S3C2410_RTCREG(0x60)
+#define S3C2410_ALMMON S3C2410_RTCREG(0x64)
+#define S3C2410_ALMYEAR S3C2410_RTCREG(0x68)
+#define S3C2410_RTCSEC S3C2410_RTCREG(0x70)
+#define S3C2410_RTCMIN S3C2410_RTCREG(0x74)
+#define S3C2410_RTCHOUR S3C2410_RTCREG(0x78)
+#define S3C2410_RTCDATE S3C2410_RTCREG(0x7c)
+#define S3C2410_RTCMON S3C2410_RTCREG(0x84)
+#define S3C2410_RTCYEAR S3C2410_RTCREG(0x88)
#endif /* __ASM_ARCH_REGS_RTC_H */
diff --git a/arch/arm/plat-samsung/include/plat/rtc-core.h b/arch/arm/plat-samsung/include/plat/rtc-core.h
new file mode 100644
index 0000000000000000000000000000000000000000..21d8594d37cac03feb2ebbede2cf977ff636123f
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/rtc-core.h
@@ -0,0 +1,27 @@
+/* linux/arch/arm/plat-samsung/include/plat/rtc-core.h
+ *
+ * Copyright (c) 2011 Heiko Stuebner <heiko@sntech.de>
+ *
+ * Samsung RTC Controller core functions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_PLAT_RTC_CORE_H
+#define __ASM_PLAT_RTC_CORE_H __FILE__
+
+/* These functions are only for use with the core support code, such as
+ * the cpu specific initialisation code
+ */
+
+/* re-define device name depending on support. */
+static inline void s3c_rtc_setname(char *name)
+{
+#if defined(CONFIG_SAMSUNG_DEV_RTC) || defined(CONFIG_PLAT_S3C24XX)
+ s3c_device_rtc.name = name;
+#endif
+}
+
+#endif /* __ASM_PLAT_RTC_CORE_H */
diff --git a/arch/arm/plat-samsung/include/plat/sdhci.h b/arch/arm/plat-samsung/include/plat/sdhci.h
index f82f888b91a95bb0a238975b4c575408728eb1e9..317e246ffc5604e1c0712054b90c5da23654a6da 100644
--- a/arch/arm/plat-samsung/include/plat/sdhci.h
+++ b/arch/arm/plat-samsung/include/plat/sdhci.h
@@ -40,6 +40,7 @@ enum clk_types {
* struct s3c_sdhci_platdata() - Platform device data for Samsung SDHCI
* @max_width: The maximum number of data bits supported.
* @host_caps: Standard MMC host capabilities bit field.
+ * @host_caps2: The second standard MMC host capabilities bit field.
* @cd_type: Type of Card Detection method (see cd_types enum above)
* @clk_type: Type of clock divider method (see clk_types enum above)
* @ext_cd_init: Initialize external card detect subsystem. Called on
@@ -63,6 +64,7 @@ enum clk_types {
struct s3c_sdhci_platdata {
unsigned int max_width;
unsigned int host_caps;
+ unsigned int host_caps2;
unsigned int pm_caps;
enum cd_types cd_type;
enum clk_types clk_type;
diff --git a/arch/arm/plat-samsung/platformdata.c b/arch/arm/plat-samsung/platformdata.c
index 0f707184eae0b0d07cb7cecc2e3d5464182ee4ce..fa78aa710ed1dc0592dc47effd416bc95fd6a1d8 100644
--- a/arch/arm/plat-samsung/platformdata.c
+++ b/arch/arm/plat-samsung/platformdata.c
@@ -53,6 +53,8 @@ void s3c_sdhci_set_platdata(struct s3c_sdhci_platdata *pd,
set->cfg_gpio = pd->cfg_gpio;
if (pd->host_caps)
set->host_caps |= pd->host_caps;
+ if (pd->host_caps2)
+ set->host_caps2 |= pd->host_caps2;
if (pd->pm_caps)
set->pm_caps |= pd->pm_caps;
if (pd->clk_type)
diff --git a/drivers/gpio/gpio-tegra.c b/drivers/gpio/gpio-tegra.c
index bdc2937915906fa7a7589b02e258daccb7b024f7..6f17671260e17b94d8176befe18e6706eb228832 100644
--- a/drivers/gpio/gpio-tegra.c
+++ b/drivers/gpio/gpio-tegra.c
@@ -25,6 +25,7 @@
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/module.h>
+#include <linux/irqdomain.h>
#include <asm/mach/irq.h>
@@ -74,9 +75,10 @@ struct tegra_gpio_bank {
#endif
};
-
+static struct irq_domain *irq_domain;
static void __iomem *regs;
-static struct tegra_gpio_bank tegra_gpio_banks[7];
+static u32 tegra_gpio_bank_count;
+static struct tegra_gpio_bank *tegra_gpio_banks;
static inline void tegra_gpio_writel(u32 val, u32 reg)
{
@@ -139,7 +141,7 @@ static int tegra_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
static int tegra_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
{
- return TEGRA_GPIO_TO_IRQ(offset);
+ return irq_find_mapping(irq_domain, offset);
}
static struct gpio_chip tegra_gpio_chip = {
@@ -155,28 +157,28 @@ static struct gpio_chip tegra_gpio_chip = {
static void tegra_gpio_irq_ack(struct irq_data *d)
{
- int gpio = d->irq - INT_GPIO_BASE;
+ int gpio = d->hwirq;
tegra_gpio_writel(1 << GPIO_BIT(gpio), GPIO_INT_CLR(gpio));
}
static void tegra_gpio_irq_mask(struct irq_data *d)
{
- int gpio = d->irq - INT_GPIO_BASE;
+ int gpio = d->hwirq;
tegra_gpio_mask_write(GPIO_MSK_INT_ENB(gpio), gpio, 0);
}
static void tegra_gpio_irq_unmask(struct irq_data *d)
{
- int gpio = d->irq - INT_GPIO_BASE;
+ int gpio = d->hwirq;
tegra_gpio_mask_write(GPIO_MSK_INT_ENB(gpio), gpio, 1);
}
static int tegra_gpio_irq_set_type(struct irq_data *d, unsigned int type)
{
- int gpio = d->irq - INT_GPIO_BASE;
+ int gpio = d->hwirq;
struct tegra_gpio_bank *bank = irq_data_get_irq_chip_data(d);
int port = GPIO_PORT(gpio);
int lvl_type;
@@ -273,7 +275,7 @@ void tegra_gpio_resume(void)
local_irq_save(flags);
- for (b = 0; b < ARRAY_SIZE(tegra_gpio_banks); b++) {
+ for (b = 0; b < tegra_gpio_bank_count; b++) {
struct tegra_gpio_bank *bank = &tegra_gpio_banks[b];
for (p = 0; p < ARRAY_SIZE(bank->oe); p++) {
@@ -296,7 +298,7 @@ void tegra_gpio_suspend(void)
int p;
local_irq_save(flags);
- for (b = 0; b < ARRAY_SIZE(tegra_gpio_banks); b++) {
+ for (b = 0; b < tegra_gpio_bank_count; b++) {
struct tegra_gpio_bank *bank = &tegra_gpio_banks[b];
for (p = 0; p < ARRAY_SIZE(bank->oe); p++) {
@@ -337,13 +339,44 @@ static struct lock_class_key gpio_lock_class;
static int __devinit tegra_gpio_probe(struct platform_device *pdev)
{
+ int irq_base;
struct resource *res;
struct tegra_gpio_bank *bank;
int gpio;
int i;
int j;
- for (i = 0; i < ARRAY_SIZE(tegra_gpio_banks); i++) {
+ for (;;) {
+ res = platform_get_resource(pdev, IORESOURCE_IRQ, tegra_gpio_bank_count);
+ if (!res)
+ break;
+ tegra_gpio_bank_count++;
+ }
+ if (!tegra_gpio_bank_count) {
+ dev_err(&pdev->dev, "Missing IRQ resource\n");
+ return -ENODEV;
+ }
+
+ tegra_gpio_chip.ngpio = tegra_gpio_bank_count * 32;
+
+ tegra_gpio_banks = devm_kzalloc(&pdev->dev,
+ tegra_gpio_bank_count * sizeof(*tegra_gpio_banks),
+ GFP_KERNEL);
+ if (!tegra_gpio_banks) {
+ dev_err(&pdev->dev, "Couldn't allocate bank structure\n");
+ return -ENODEV;
+ }
+
+ irq_base = irq_alloc_descs(-1, 0, tegra_gpio_chip.ngpio, 0);
+ if (irq_base < 0) {
+ dev_err(&pdev->dev, "Couldn't allocate IRQ numbers\n");
+ return -ENODEV;
+ }
+ irq_domain = irq_domain_add_legacy(pdev->dev.of_node,
+ tegra_gpio_chip.ngpio, irq_base, 0,
+ &irq_domain_simple_ops, NULL);
+
+ for (i = 0; i < tegra_gpio_bank_count; i++) {
res = platform_get_resource(pdev, IORESOURCE_IRQ, i);
if (!res) {
dev_err(&pdev->dev, "Missing IRQ resource\n");
@@ -380,8 +413,8 @@ static int __devinit tegra_gpio_probe(struct platform_device *pdev)
gpiochip_add(&tegra_gpio_chip);
- for (gpio = 0; gpio < TEGRA_NR_GPIOS; gpio++) {
- int irq = TEGRA_GPIO_TO_IRQ(gpio);
+ for (gpio = 0; gpio < tegra_gpio_chip.ngpio; gpio++) {
+ int irq = irq_find_mapping(irq_domain, gpio);
/* No validity check; all Tegra GPIOs are valid IRQs */
bank = &tegra_gpio_banks[GPIO_BANK(gpio)];
@@ -393,7 +426,7 @@ static int __devinit tegra_gpio_probe(struct platform_device *pdev)
set_irq_flags(irq, IRQF_VALID);
}
- for (i = 0; i < ARRAY_SIZE(tegra_gpio_banks); i++) {
+ for (i = 0; i < tegra_gpio_bank_count; i++) {
bank = &tegra_gpio_banks[i];
irq_set_chained_handler(bank->irq, tegra_gpio_irq_handler);
diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
index 124d9c594f40bc0052b8d0e1cc4861d0024fdfa0..dfb84b7ee5503ae38a955ba843ff7f17226d3161 100644
--- a/drivers/i2c/busses/i2c-imx.c
+++ b/drivers/i2c/busses/i2c-imx.c
@@ -191,7 +191,7 @@ static int i2c_imx_start(struct imx_i2c_struct *i2c_imx)
dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
- clk_enable(i2c_imx->clk);
+ clk_prepare_enable(i2c_imx->clk);
writeb(i2c_imx->ifdr, i2c_imx->base + IMX_I2C_IFDR);
/* Enable I2C controller */
writeb(0, i2c_imx->base + IMX_I2C_I2SR);
@@ -240,7 +240,7 @@ static void i2c_imx_stop(struct imx_i2c_struct *i2c_imx)
/* Disable I2C controller */
writeb(0, i2c_imx->base + IMX_I2C_I2CR);
- clk_disable(i2c_imx->clk);
+ clk_disable_unprepare(i2c_imx->clk);
}
static void __init i2c_imx_set_clk(struct imx_i2c_struct *i2c_imx,
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index 0be4e2013632f97ce4dddc489212c2ed6f7c4985..6193a0d7bde52b8cc29e52837179d90eed50faeb 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -464,7 +464,7 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
err = PTR_ERR(clk);
goto err_clk_get;
}
- clk_enable(clk);
+ clk_prepare_enable(clk);
pltfm_host->clk = clk;
if (!is_imx25_esdhc(imx_data))
@@ -559,7 +559,7 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
gpio_free(boarddata->wp_gpio);
no_card_detect_pin:
no_board_data:
- clk_disable(pltfm_host->clk);
+ clk_disable_unprepare(pltfm_host->clk);
clk_put(pltfm_host->clk);
err_clk_get:
kfree(imx_data);
@@ -586,7 +586,7 @@ static int __devexit sdhci_esdhc_imx_remove(struct platform_device *pdev)
gpio_free(boarddata->cd_gpio);
}
- clk_disable(pltfm_host->clk);
+ clk_disable_unprepare(pltfm_host->clk);
clk_put(pltfm_host->clk);
kfree(imx_data);
diff --git a/drivers/mmc/host/sdhci-s3c.c b/drivers/mmc/host/sdhci-s3c.c
index 1af756ee0f9ab5e43db1a348505021a6fd5eee28..b19e7d435f8d6d1561a60156dff038c7508e0e2e 100644
--- a/drivers/mmc/host/sdhci-s3c.c
+++ b/drivers/mmc/host/sdhci-s3c.c
@@ -518,9 +518,6 @@ static int __devinit sdhci_s3c_probe(struct platform_device *pdev)
if (pdata->cd_type == S3C_SDHCI_CD_PERMANENT)
host->mmc->caps = MMC_CAP_NONREMOVABLE;
- if (pdata->host_caps)
- host->mmc->caps |= pdata->host_caps;
-
if (pdata->pm_caps)
host->mmc->pm_caps |= pdata->pm_caps;
@@ -544,6 +541,9 @@ static int __devinit sdhci_s3c_probe(struct platform_device *pdev)
if (pdata->host_caps)
host->mmc->caps |= pdata->host_caps;
+ if (pdata->host_caps2)
+ host->mmc->caps2 |= pdata->host_caps2;
+
ret = sdhci_add_host(host);
if (ret) {
dev_err(dev, "sdhci_add_host() failed\n");
diff --git a/drivers/net/Space.c b/drivers/net/Space.c
index 068c3563e00fb6e9048356209a5c50146e0cf3bd..88bbd8ffa7fe739d0814c3da55e3b64429021d0d 100644
--- a/drivers/net/Space.c
+++ b/drivers/net/Space.c
@@ -190,8 +190,10 @@ static struct devprobe2 isa_probes[] __initdata = {
{seeq8005_probe, 0},
#endif
#ifdef CONFIG_CS89x0
+#ifndef CONFIG_CS89x0_PLATFORM
{cs89x0_probe, 0},
#endif
+#endif
#ifdef CONFIG_AT1700
{at1700_probe, 0},
#endif
diff --git a/drivers/net/ethernet/cirrus/Kconfig b/drivers/net/ethernet/cirrus/Kconfig
index 1f8648f099c7328d3c8334375d324b413ddb3543..8388e36cf08f97b17d75230b68e3683a3a2b365e 100644
--- a/drivers/net/ethernet/cirrus/Kconfig
+++ b/drivers/net/ethernet/cirrus/Kconfig
@@ -5,8 +5,7 @@
config NET_VENDOR_CIRRUS
bool "Cirrus devices"
default y
- depends on ISA || EISA || MACH_IXDP2351 || ARCH_IXDP2X01 \
- || MACH_MX31ADS || MACH_QQ2440 || (ARM && ARCH_EP93XX) || MAC
+ depends on ISA || EISA || ARM || MAC
---help---
If you have a network (Ethernet) card belonging to this class, say Y
and read the Ethernet-HOWTO, available from
@@ -21,8 +20,7 @@ if NET_VENDOR_CIRRUS
config CS89x0
tristate "CS89x0 support"
- depends on (ISA || EISA || MACH_IXDP2351 \
- || ARCH_IXDP2X01 || MACH_MX31ADS || MACH_QQ2440)
+ depends on ISA || EISA || ARM
---help---
Support for CS89x0 chipset based Ethernet cards. If you have a
network (Ethernet) card of this type, say Y and read the
@@ -33,10 +31,15 @@ config CS89x0
To compile this driver as a module, choose M here. The module
will be called cs89x0.
-config CS89x0_NONISA_IRQ
- def_bool y
- depends on CS89x0 != n
- depends on MACH_IXDP2351 || ARCH_IXDP2X01 || MACH_MX31ADS || MACH_QQ2440
+config CS89x0_PLATFORM
+ bool "CS89x0 platform driver support"
+ depends on CS89x0
+ help
+ Say Y to compile the cs89x0 driver as a platform driver. This
+ makes this driver suitable for use on certain evaluation boards
+ such as the iMX21ADS.
+
+ If you are unsure, say N.
config EP93XX_ETH
tristate "EP93xx Ethernet support"
diff --git a/drivers/net/ethernet/cirrus/cs89x0.c b/drivers/net/ethernet/cirrus/cs89x0.c
index d5ff93653e4ce0af7ca54fa84a182b32bebf0860..30fee428c4891efe65eee52337f7e54061e5eb5d 100644
--- a/drivers/net/ethernet/cirrus/cs89x0.c
+++ b/drivers/net/ethernet/cirrus/cs89x0.c
@@ -100,9 +100,6 @@
*/
-/* Always include 'config.h' first in case the user wants to turn on
- or override something. */
-#include <linux/module.h>
/*
* Set this to zero to disable DMA code
@@ -131,9 +128,12 @@
*/
+#include <linux/module.h>
+#include <linux/printk.h>
#include <linux/errno.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
+#include <linux/platform_device.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/fcntl.h>
@@ -151,6 +151,7 @@
#include <asm/system.h>
#include <asm/io.h>
#include <asm/irq.h>
+#include <linux/atomic.h>
#if ALLOW_DMA
#include <asm/dma.h>
#endif
@@ -174,26 +175,20 @@ static char version[] __initdata =
them to system IRQ numbers. This mapping is card specific and is set to
the configuration of the Cirrus Eval board for this chip. */
#if defined(CONFIG_MACH_IXDP2351)
+#define CS89x0_NONISA_IRQ
static unsigned int netcard_portlist[] __used __initdata = {IXDP2351_VIRT_CS8900_BASE, 0};
static unsigned int cs8900_irq_map[] = {IRQ_IXDP2351_CS8900, 0, 0, 0};
#elif defined(CONFIG_ARCH_IXDP2X01)
+#define CS89x0_NONISA_IRQ
static unsigned int netcard_portlist[] __used __initdata = {IXDP2X01_CS8900_VIRT_BASE, 0};
static unsigned int cs8900_irq_map[] = {IRQ_IXDP2X01_CS8900, 0, 0, 0};
-#elif defined(CONFIG_MACH_QQ2440)
-#include <mach/qq2440.h>
-static unsigned int netcard_portlist[] __used __initdata = { QQ2440_CS8900_VIRT_BASE + 0x300, 0 };
-static unsigned int cs8900_irq_map[] = { QQ2440_CS8900_IRQ, 0, 0, 0 };
-#elif defined(CONFIG_MACH_MX31ADS)
-#include <mach/board-mx31ads.h>
-static unsigned int netcard_portlist[] __used __initdata = {
- PBC_BASE_ADDRESS + PBC_CS8900A_IOBASE + 0x300, 0
-};
-static unsigned cs8900_irq_map[] = {EXPIO_INT_ENET_INT, 0, 0, 0};
#else
+#ifndef CONFIG_CS89x0_PLATFORM
static unsigned int netcard_portlist[] __used __initdata =
{ 0x300, 0x320, 0x340, 0x360, 0x200, 0x220, 0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x2e0, 0};
static unsigned int cs8900_irq_map[] = {10,11,12,5};
#endif
+#endif
#if DEBUGGING
static unsigned int net_debug = DEBUGGING;
@@ -236,11 +231,16 @@ struct net_local {
unsigned char *end_dma_buff; /* points to the end of the buffer */
unsigned char *rx_dma_ptr; /* points to the next packet */
#endif
+#ifdef CONFIG_CS89x0_PLATFORM
+ void __iomem *virt_addr;/* Virtual address for accessing the CS89x0. */
+ unsigned long phys_addr;/* Physical address for accessing the CS89x0. */
+ unsigned long size; /* Length of CS89x0 memory region. */
+#endif
};
/* Index to functions, as function prototypes. */
-static int cs89x0_probe1(struct net_device *dev, int ioaddr, int modular);
+static int cs89x0_probe1(struct net_device *dev, unsigned long ioaddr, int modular);
static int net_open(struct net_device *dev);
static netdev_tx_t net_send_packet(struct sk_buff *skb, struct net_device *dev);
static irqreturn_t net_interrupt(int irq, void *dev_id);
@@ -294,6 +294,7 @@ static int __init media_fn(char *str)
__setup("cs89x0_media=", media_fn);
+#ifndef CONFIG_CS89x0_PLATFORM
/* Check for a network adaptor of this type, and return '0' iff one exists.
If dev->base_addr == 0, probe all likely locations.
If dev->base_addr == 1, always return failure.
@@ -343,6 +344,7 @@ struct net_device * __init cs89x0_probe(int unit)
return ERR_PTR(err);
}
#endif
+#endif
#if defined(CONFIG_MACH_IXDP2351)
static u16
@@ -504,7 +506,7 @@ static const struct net_device_ops net_ops = {
*/
static int __init
-cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
+cs89x0_probe1(struct net_device *dev, unsigned long ioaddr, int modular)
{
struct net_local *lp = netdev_priv(dev);
static unsigned version_printed;
@@ -529,15 +531,12 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
lp->force = g_cs89x0_media__force;
#endif
-#if defined(CONFIG_MACH_QQ2440)
- lp->force |= FORCE_RJ45 | FORCE_FULL;
-#endif
}
/* Grab the region so we can find another board if autoIRQ fails. */
/* WTF is going on here? */
if (!request_region(ioaddr & ~3, NETCARD_IO_EXTENT, DRV_NAME)) {
- printk(KERN_ERR "%s: request_region(0x%x, 0x%x) failed\n",
+ printk(KERN_ERR "%s: request_region(0x%lx, 0x%x) failed\n",
DRV_NAME, ioaddr, NETCARD_IO_EXTENT);
retval = -EBUSY;
goto out1;
@@ -549,7 +548,7 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
will skip the test for the ADD_PORT. */
if (ioaddr & 1) {
if (net_debug > 1)
- printk(KERN_INFO "%s: odd ioaddr 0x%x\n", dev->name, ioaddr);
+ printk(KERN_INFO "%s: odd ioaddr 0x%lx\n", dev->name, ioaddr);
if ((ioaddr & 2) != 2)
if ((readword(ioaddr & ~3, ADD_PORT) & ADD_MASK) != ADD_SIG) {
printk(KERN_ERR "%s: bad signature 0x%x\n",
@@ -560,13 +559,13 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
}
ioaddr &= ~3;
- printk(KERN_DEBUG "PP_addr at %x[%x]: 0x%x\n",
+ printk(KERN_DEBUG "PP_addr at %lx[%x]: 0x%x\n",
ioaddr, ADD_PORT, readword(ioaddr, ADD_PORT));
writeword(ioaddr, ADD_PORT, PP_ChipID);
tmp = readword(ioaddr, DATA_PORT);
if (tmp != CHIP_EISA_ID_SIG) {
- printk(KERN_DEBUG "%s: incorrect signature at %x[%x]: 0x%x!="
+ printk(KERN_DEBUG "%s: incorrect signature at %lx[%x]: 0x%x!="
CHIP_EISA_ID_SIG_STR "\n",
dev->name, ioaddr, DATA_PORT, tmp);
retval = -ENODEV;
@@ -736,8 +735,9 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
dev->irq = i;
} else {
i = lp->isa_config & INT_NO_MASK;
+#ifndef CONFIG_CS89x0_PLATFORM
if (lp->chip_type == CS8900) {
-#ifdef CONFIG_CS89x0_NONISA_IRQ
+#ifdef CS89x0_NONISA_IRQ
i = cs8900_irq_map[0];
#else
/* Translate the IRQ using the IRQ mapping table. */
@@ -758,6 +758,7 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
}
#endif
}
+#endif
if (!dev->irq)
dev->irq = i;
}
@@ -1168,6 +1169,7 @@ write_irq(struct net_device *dev, int chip_type, int irq)
int i;
if (chip_type == CS8900) {
+#ifndef CONFIG_CS89x0_PLATFORM
/* Search the mapping table for the corresponding IRQ pin. */
for (i = 0; i != ARRAY_SIZE(cs8900_irq_map); i++)
if (cs8900_irq_map[i] == irq)
@@ -1175,6 +1177,10 @@ write_irq(struct net_device *dev, int chip_type, int irq)
/* Not found */
if (i == ARRAY_SIZE(cs8900_irq_map))
i = 3;
+#else
+ /* INTRQ0 pin is used for interrupt generation. */
+ i = 0;
+#endif
writereg(dev, PP_CS8900_ISAINT, i);
} else {
writereg(dev, PP_CS8920_ISAINT, irq);
@@ -1228,7 +1234,7 @@ net_open(struct net_device *dev)
}
else
{
-#ifndef CONFIG_CS89x0_NONISA_IRQ
+#if !defined(CS89x0_NONISA_IRQ) && !defined(CONFIG_CS89x0_PLATFORM)
if (((1 << dev->irq) & lp->irq_map) == 0) {
printk(KERN_ERR "%s: IRQ %d is not in our map of allowable IRQs, which is %x\n",
dev->name, dev->irq, lp->irq_map);
@@ -1746,7 +1752,7 @@ static int set_mac_address(struct net_device *dev, void *p)
return 0;
}
-#ifdef MODULE
+#if defined(MODULE) && !defined(CONFIG_CS89x0_PLATFORM)
static struct net_device *dev_cs89x0;
@@ -1900,7 +1906,97 @@ cleanup_module(void)
release_region(dev_cs89x0->base_addr, NETCARD_IO_EXTENT);
free_netdev(dev_cs89x0);
}
-#endif /* MODULE */
+#endif /* MODULE && !CONFIG_CS89x0_PLATFORM */
+
+#ifdef CONFIG_CS89x0_PLATFORM
+static int __init cs89x0_platform_probe(struct platform_device *pdev)
+{
+ struct net_device *dev = alloc_etherdev(sizeof(struct net_local));
+ struct net_local *lp;
+ struct resource *mem_res;
+ int err;
+
+ if (!dev)
+ return -ENOMEM;
+
+ lp = netdev_priv(dev);
+
+ mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ dev->irq = platform_get_irq(pdev, 0);
+ if (mem_res == NULL || dev->irq <= 0) {
+ dev_warn(&dev->dev, "memory/interrupt resource missing.\n");
+ err = -ENXIO;
+ goto free;
+ }
+
+ lp->phys_addr = mem_res->start;
+ lp->size = resource_size(mem_res);
+ if (!request_mem_region(lp->phys_addr, lp->size, DRV_NAME)) {
+ dev_warn(&dev->dev, "request_mem_region() failed.\n");
+ err = -EBUSY;
+ goto free;
+ }
+
+ lp->virt_addr = ioremap(lp->phys_addr, lp->size);
+ if (!lp->virt_addr) {
+ dev_warn(&dev->dev, "ioremap() failed.\n");
+ err = -ENOMEM;
+ goto release;
+ }
+
+ err = cs89x0_probe1(dev, (unsigned long)lp->virt_addr, 0);
+ if (err) {
+ dev_warn(&dev->dev, "no cs8900 or cs8920 detected.\n");
+ goto unmap;
+ }
+
+ platform_set_drvdata(pdev, dev);
+ return 0;
+
+unmap:
+ iounmap(lp->virt_addr);
+release:
+ release_mem_region(lp->phys_addr, lp->size);
+free:
+ free_netdev(dev);
+ return err;
+}
+
+static int cs89x0_platform_remove(struct platform_device *pdev)
+{
+ struct net_device *dev = platform_get_drvdata(pdev);
+ struct net_local *lp = netdev_priv(dev);
+
+ unregister_netdev(dev);
+ iounmap(lp->virt_addr);
+ release_mem_region(lp->phys_addr, lp->size);
+ free_netdev(dev);
+ return 0;
+}
+
+static struct platform_driver cs89x0_driver = {
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+ .remove = cs89x0_platform_remove,
+};
+
+static int __init cs89x0_init(void)
+{
+ return platform_driver_probe(&cs89x0_driver, cs89x0_platform_probe);
+}
+
+module_init(cs89x0_init);
+
+static void __exit cs89x0_cleanup(void)
+{
+ platform_driver_unregister(&cs89x0_driver);
+}
+
+module_exit(cs89x0_cleanup);
+
+#endif /* CONFIG_CS89x0_PLATFORM */
/*
* Local variables:
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index a229de98ae6f286171c3ce96ddb0d8d6f299108e..36db5a441ebacda2498fc4cfcc5b0e24d9437a9f 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -258,14 +258,6 @@ config REGULATOR_DB8500_PRCMU
This driver supports the voltage domain regulators controlled by the
DB8500 PRCMU
-config REGULATOR_BQ24022
- tristate "TI bq24022 Dual Input 1-Cell Li-Ion Charger IC"
- help
- This driver controls a TI bq24022 Charger attached via
- GPIOs. The provided current regulator can enable/disable
- charging select between 100 mA and 500 mA charging current
- limit.
-
config REGULATOR_TPS6105X
tristate "TI TPS6105X Power regulators"
depends on TPS6105X
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index b5042c885d8921af2d105f55dcf521bf4bd447be..94b52745e9579ec3fbb9790efef74a5d41315770 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -16,7 +16,6 @@ obj-$(CONFIG_REGULATOR_AB3100) += ab3100.o
obj-$(CONFIG_REGULATOR_AB8500) += ab8500.o
obj-$(CONFIG_REGULATOR_AD5398) += ad5398.o
obj-$(CONFIG_REGULATOR_ANATOP) += anatop-regulator.o
-obj-$(CONFIG_REGULATOR_BQ24022) += bq24022.o
obj-$(CONFIG_REGULATOR_DA903X) += da903x.o
obj-$(CONFIG_REGULATOR_DA9052) += da9052-regulator.o
obj-$(CONFIG_REGULATOR_DBX500_PRCMU) += dbx500-prcmu.o
diff --git a/drivers/regulator/bq24022.c b/drivers/regulator/bq24022.c
deleted file mode 100644
index 9fab6d1bbe80d28a1f388e8bc2bdb14589c8702e..0000000000000000000000000000000000000000
--- a/drivers/regulator/bq24022.c
+++ /dev/null
@@ -1,162 +0,0 @@
-/*
- * Support for TI bq24022 (bqTINY-II) Dual Input (USB/AC Adpater)
- * 1-Cell Li-Ion Charger connected via GPIOs.
- *
- * Copyright (c) 2008 Philipp Zabel
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/err.h>
-#include <linux/module.h>
-#include <linux/gpio.h>
-#include <linux/regulator/bq24022.h>
-#include <linux/regulator/driver.h>
-
-
-static int bq24022_set_current_limit(struct regulator_dev *rdev,
- int min_uA, int max_uA)
-{
- struct bq24022_mach_info *pdata = rdev_get_drvdata(rdev);
-
- dev_dbg(rdev_get_dev(rdev), "setting current limit to %s mA\n",
- max_uA >= 500000 ? "500" : "100");
-
- /* REVISIT: maybe return error if min_uA != 0 ? */
- gpio_set_value(pdata->gpio_iset2, max_uA >= 500000);
- return 0;
-}
-
-static int bq24022_get_current_limit(struct regulator_dev *rdev)
-{
- struct bq24022_mach_info *pdata = rdev_get_drvdata(rdev);
-
- return gpio_get_value(pdata->gpio_iset2) ? 500000 : 100000;
-}
-
-static int bq24022_enable(struct regulator_dev *rdev)
-{
- struct bq24022_mach_info *pdata = rdev_get_drvdata(rdev);
-
- dev_dbg(rdev_get_dev(rdev), "enabling charger\n");
-
- gpio_set_value(pdata->gpio_nce, 0);
- return 0;
-}
-
-static int bq24022_disable(struct regulator_dev *rdev)
-{
- struct bq24022_mach_info *pdata = rdev_get_drvdata(rdev);
-
- dev_dbg(rdev_get_dev(rdev), "disabling charger\n");
-
- gpio_set_value(pdata->gpio_nce, 1);
- return 0;
-}
-
-static int bq24022_is_enabled(struct regulator_dev *rdev)
-{
- struct bq24022_mach_info *pdata = rdev_get_drvdata(rdev);
-
- return !gpio_get_value(pdata->gpio_nce);
-}
-
-static struct regulator_ops bq24022_ops = {
- .set_current_limit = bq24022_set_current_limit,
- .get_current_limit = bq24022_get_current_limit,
- .enable = bq24022_enable,
- .disable = bq24022_disable,
- .is_enabled = bq24022_is_enabled,
-};
-
-static struct regulator_desc bq24022_desc = {
- .name = "bq24022",
- .ops = &bq24022_ops,
- .type = REGULATOR_CURRENT,
- .owner = THIS_MODULE,
-};
-
-static int __init bq24022_probe(struct platform_device *pdev)
-{
- struct bq24022_mach_info *pdata = pdev->dev.platform_data;
- struct regulator_dev *bq24022;
- int ret;
-
- if (!pdata || !pdata->gpio_nce || !pdata->gpio_iset2)
- return -EINVAL;
-
- ret = gpio_request(pdata->gpio_nce, "ncharge_en");
- if (ret) {
- dev_dbg(&pdev->dev, "couldn't request nCE GPIO: %d\n",
- pdata->gpio_nce);
- goto err_ce;
- }
- ret = gpio_request(pdata->gpio_iset2, "charge_mode");
- if (ret) {
- dev_dbg(&pdev->dev, "couldn't request ISET2 GPIO: %d\n",
- pdata->gpio_iset2);
- goto err_iset2;
- }
- ret = gpio_direction_output(pdata->gpio_iset2, 0);
- ret = gpio_direction_output(pdata->gpio_nce, 1);
-
- bq24022 = regulator_register(&bq24022_desc, &pdev->dev,
- pdata->init_data, pdata, NULL);
- if (IS_ERR(bq24022)) {
- dev_dbg(&pdev->dev, "couldn't register regulator\n");
- ret = PTR_ERR(bq24022);
- goto err_reg;
- }
- platform_set_drvdata(pdev, bq24022);
- dev_dbg(&pdev->dev, "registered regulator\n");
-
- return 0;
-err_reg:
- gpio_free(pdata->gpio_iset2);
-err_iset2:
- gpio_free(pdata->gpio_nce);
-err_ce:
- return ret;
-}
-
-static int __devexit bq24022_remove(struct platform_device *pdev)
-{
- struct bq24022_mach_info *pdata = pdev->dev.platform_data;
- struct regulator_dev *bq24022 = platform_get_drvdata(pdev);
-
- regulator_unregister(bq24022);
- gpio_free(pdata->gpio_iset2);
- gpio_free(pdata->gpio_nce);
-
- return 0;
-}
-
-static struct platform_driver bq24022_driver = {
- .driver = {
- .name = "bq24022",
- },
- .remove = __devexit_p(bq24022_remove),
-};
-
-static int __init bq24022_init(void)
-{
- return platform_driver_probe(&bq24022_driver, bq24022_probe);
-}
-
-static void __exit bq24022_exit(void)
-{
- platform_driver_unregister(&bq24022_driver);
-}
-
-module_init(bq24022_init);
-module_exit(bq24022_exit);
-
-MODULE_AUTHOR("Philipp Zabel");
-MODULE_DESCRIPTION("TI bq24022 Li-Ion Charger driver");
-MODULE_LICENSE("GPL");
diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 4768a9d283758f16f6deeb702d125be9bf60095c..8c8377d50c4c4578724c6149bbd084744e7c92fb 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -780,8 +780,8 @@ config RTC_DRV_EP93XX
will be called rtc-ep93xx.
config RTC_DRV_SA1100
- tristate "SA11x0/PXA2xx"
- depends on ARCH_SA1100 || ARCH_PXA
+ tristate "SA11x0/PXA2xx/PXA910"
+ depends on ARCH_SA1100 || ARCH_PXA || ARCH_MMP
help
If you say Y here you will get access to the real time clock
built into your SA11x0 or PXA2xx CPU.
diff --git a/drivers/rtc/rtc-s3c.c b/drivers/rtc/rtc-s3c.c
index c543f6f1eec2f8d75500d8c77317ed2fcd3136f7..9ccea134a9965a1b2878f6873ae933fb72ca0b1a 100644
--- a/drivers/rtc/rtc-s3c.c
+++ b/drivers/rtc/rtc-s3c.c
@@ -35,6 +35,8 @@
enum s3c_cpu_type {
TYPE_S3C2410,
+ TYPE_S3C2416,
+ TYPE_S3C2443,
TYPE_S3C64XX,
};
@@ -132,6 +134,7 @@ static int s3c_rtc_setfreq(struct device *dev, int freq)
struct platform_device *pdev = to_platform_device(dev);
struct rtc_device *rtc_dev = platform_get_drvdata(pdev);
unsigned int tmp = 0;
+ int val;
if (!is_power_of_2(freq))
return -EINVAL;
@@ -139,12 +142,22 @@ static int s3c_rtc_setfreq(struct device *dev, int freq)
clk_enable(rtc_clk);
spin_lock_irq(&s3c_rtc_pie_lock);
- if (s3c_rtc_cpu_type == TYPE_S3C2410) {
+ if (s3c_rtc_cpu_type != TYPE_S3C64XX) {
tmp = readb(s3c_rtc_base + S3C2410_TICNT);
tmp &= S3C2410_TICNT_ENABLE;
}
- tmp |= (rtc_dev->max_user_freq / freq)-1;
+ val = (rtc_dev->max_user_freq / freq) - 1;
+
+ if (s3c_rtc_cpu_type == TYPE_S3C2416 || s3c_rtc_cpu_type == TYPE_S3C2443) {
+ tmp |= S3C2443_TICNT_PART(val);
+ writel(S3C2443_TICNT1_PART(val), s3c_rtc_base + S3C2443_TICNT1);
+
+ if (s3c_rtc_cpu_type == TYPE_S3C2416)
+ writel(S3C2416_TICNT2_PART(val), s3c_rtc_base + S3C2416_TICNT2);
+ } else {
+ tmp |= val;
+ }
writel(tmp, s3c_rtc_base + S3C2410_TICNT);
spin_unlock_irq(&s3c_rtc_pie_lock);
@@ -371,7 +384,7 @@ static void s3c_rtc_enable(struct platform_device *pdev, int en)
tmp &= ~S3C2410_RTCCON_RTCEN;
writew(tmp, base + S3C2410_RTCCON);
- if (s3c_rtc_cpu_type == TYPE_S3C2410) {
+ if (s3c_rtc_cpu_type != TYPE_S3C64XX) {
tmp = readb(base + S3C2410_TICNT);
tmp &= ~S3C2410_TICNT_ENABLE;
writeb(tmp, base + S3C2410_TICNT);
@@ -428,12 +441,27 @@ static int __devexit s3c_rtc_remove(struct platform_device *dev)
return 0;
}
+static const struct of_device_id s3c_rtc_dt_match[];
+
+static inline int s3c_rtc_get_driver_data(struct platform_device *pdev)
+{
+#ifdef CONFIG_OF
+ if (pdev->dev.of_node) {
+ const struct of_device_id *match;
+ match = of_match_node(s3c_rtc_dt_match, pdev->dev.of_node);
+ return match->data;
+ }
+#endif
+ return platform_get_device_id(pdev)->driver_data;
+}
+
static int __devinit s3c_rtc_probe(struct platform_device *pdev)
{
struct rtc_device *rtc;
struct rtc_time rtc_tm;
struct resource *res;
int ret;
+ int tmp;
pr_debug("%s: probe=%p\n", __func__, pdev);
@@ -508,13 +536,7 @@ static int __devinit s3c_rtc_probe(struct platform_device *pdev)
goto err_nortc;
}
-#ifdef CONFIG_OF
- if (pdev->dev.of_node)
- s3c_rtc_cpu_type = of_device_is_compatible(pdev->dev.of_node,
- "samsung,s3c6410-rtc") ? TYPE_S3C64XX : TYPE_S3C2410;
- else
-#endif
- s3c_rtc_cpu_type = platform_get_device_id(pdev)->driver_data;
+ s3c_rtc_cpu_type = s3c_rtc_get_driver_data(pdev);
/* Check RTC Time */
@@ -533,11 +555,17 @@ static int __devinit s3c_rtc_probe(struct platform_device *pdev)
dev_warn(&pdev->dev, "warning: invalid RTC value so initializing it\n");
}
- if (s3c_rtc_cpu_type == TYPE_S3C64XX)
+ if (s3c_rtc_cpu_type != TYPE_S3C2410)
rtc->max_user_freq = 32768;
else
rtc->max_user_freq = 128;
+ if (s3c_rtc_cpu_type == TYPE_S3C2416 || s3c_rtc_cpu_type == TYPE_S3C2443) {
+ tmp = readw(s3c_rtc_base + S3C2410_RTCCON);
+ tmp |= S3C2443_RTCCON_TICSEL;
+ writew(tmp, s3c_rtc_base + S3C2410_RTCCON);
+ }
+
platform_set_drvdata(pdev, rtc);
s3c_rtc_setfreq(&pdev->dev, 1);
@@ -638,8 +666,19 @@ static int s3c_rtc_resume(struct platform_device *pdev)
#ifdef CONFIG_OF
static const struct of_device_id s3c_rtc_dt_match[] = {
- { .compatible = "samsung,s3c2410-rtc" },
- { .compatible = "samsung,s3c6410-rtc" },
+ {
+ .compatible = "samsung,s3c2410-rtc"
+ .data = TYPE_S3C2410,
+ }, {
+ .compatible = "samsung,s3c2416-rtc"
+ .data = TYPE_S3C2416,
+ }, {
+ .compatible = "samsung,s3c2443-rtc"
+ .data = TYPE_S3C2443,
+ }, {
+ .compatible = "samsung,s3c6410-rtc"
+ .data = TYPE_S3C64XX,
+ },
{},
};
MODULE_DEVICE_TABLE(of, s3c_rtc_dt_match);
@@ -651,6 +690,12 @@ static struct platform_device_id s3c_rtc_driver_ids[] = {
{
.name = "s3c2410-rtc",
.driver_data = TYPE_S3C2410,
+ }, {
+ .name = "s3c2416-rtc",
+ .driver_data = TYPE_S3C2416,
+ }, {
+ .name = "s3c2443-rtc",
+ .driver_data = TYPE_S3C2443,
}, {
.name = "s3c64xx-rtc",
.driver_data = TYPE_S3C64XX,
diff --git a/drivers/rtc/rtc-sa1100.c b/drivers/rtc/rtc-sa1100.c
index 44cd81c72ea14422690866ad0cca5f42066d3dec..fa512ed420179738600c9eda0a0839565370c784 100644
--- a/drivers/rtc/rtc-sa1100.c
+++ b/drivers/rtc/rtc-sa1100.c
@@ -23,35 +23,44 @@
#include <linux/platform_device.h>
#include <linux/module.h>
+#include <linux/clk.h>
#include <linux/rtc.h>
#include <linux/init.h>
#include <linux/fs.h>
#include <linux/interrupt.h>
+#include <linux/slab.h>
#include <linux/string.h>
+#include <linux/of.h>
#include <linux/pm.h>
#include <linux/bitops.h>
#include <mach/hardware.h>
#include <asm/irq.h>
-#ifdef CONFIG_ARCH_PXA
+#if defined(CONFIG_ARCH_PXA) || defined(CONFIG_ARCH_MMP)
#include <mach/regs-rtc.h>
#endif
#define RTC_DEF_DIVIDER (32768 - 1)
#define RTC_DEF_TRIM 0
-
-static const unsigned long RTC_FREQ = 1024;
-static DEFINE_SPINLOCK(sa1100_rtc_lock);
+#define RTC_FREQ 1024
+
+struct sa1100_rtc {
+ spinlock_t lock;
+ int irq_1hz;
+ int irq_alarm;
+ struct rtc_device *rtc;
+ struct clk *clk;
+};
static irqreturn_t sa1100_rtc_interrupt(int irq, void *dev_id)
{
- struct platform_device *pdev = to_platform_device(dev_id);
- struct rtc_device *rtc = platform_get_drvdata(pdev);
+ struct sa1100_rtc *info = dev_get_drvdata(dev_id);
+ struct rtc_device *rtc = info->rtc;
unsigned int rtsr;
unsigned long events = 0;
- spin_lock(&sa1100_rtc_lock);
+ spin_lock(&info->lock);
rtsr = RTSR;
/* clear interrupt sources */
@@ -87,26 +96,28 @@ static irqreturn_t sa1100_rtc_interrupt(int irq, void *dev_id)
rtc_update_irq(rtc, 1, events);
- spin_unlock(&sa1100_rtc_lock);
+ spin_unlock(&info->lock);
return IRQ_HANDLED;
}
static int sa1100_rtc_open(struct device *dev)
{
+ struct sa1100_rtc *info = dev_get_drvdata(dev);
+ struct rtc_device *rtc = info->rtc;
int ret;
- struct platform_device *plat_dev = to_platform_device(dev);
- struct rtc_device *rtc = platform_get_drvdata(plat_dev);
- ret = request_irq(IRQ_RTC1Hz, sa1100_rtc_interrupt, 0, "rtc 1Hz", dev);
+ ret = clk_prepare_enable(info->clk);
+ if (ret)
+ goto fail_clk;
+ ret = request_irq(info->irq_1hz, sa1100_rtc_interrupt, 0, "rtc 1Hz", dev);
if (ret) {
- dev_err(dev, "IRQ %d already in use.\n", IRQ_RTC1Hz);
+ dev_err(dev, "IRQ %d already in use.\n", info->irq_1hz);
goto fail_ui;
}
- ret = request_irq(IRQ_RTCAlrm, sa1100_rtc_interrupt, 0,
- "rtc Alrm", dev);
+ ret = request_irq(info->irq_alarm, sa1100_rtc_interrupt, 0, "rtc Alrm", dev);
if (ret) {
- dev_err(dev, "IRQ %d already in use.\n", IRQ_RTCAlrm);
+ dev_err(dev, "IRQ %d already in use.\n", info->irq_alarm);
goto fail_ai;
}
rtc->max_user_freq = RTC_FREQ;
@@ -115,29 +126,36 @@ static int sa1100_rtc_open(struct device *dev)
return 0;
fail_ai:
- free_irq(IRQ_RTC1Hz, dev);
+ free_irq(info->irq_1hz, dev);
fail_ui:
+ clk_disable_unprepare(info->clk);
+ fail_clk:
return ret;
}
static void sa1100_rtc_release(struct device *dev)
{
- spin_lock_irq(&sa1100_rtc_lock);
+ struct sa1100_rtc *info = dev_get_drvdata(dev);
+
+ spin_lock_irq(&info->lock);
RTSR = 0;
- spin_unlock_irq(&sa1100_rtc_lock);
+ spin_unlock_irq(&info->lock);
- free_irq(IRQ_RTCAlrm, dev);
- free_irq(IRQ_RTC1Hz, dev);
+ free_irq(info->irq_alarm, dev);
+ free_irq(info->irq_1hz, dev);
+ clk_disable_unprepare(info->clk);
}
static int sa1100_rtc_alarm_irq_enable(struct device *dev, unsigned int enabled)
{
- spin_lock_irq(&sa1100_rtc_lock);
+ struct sa1100_rtc *info = dev_get_drvdata(dev);
+
+ spin_lock_irq(&info->lock);
if (enabled)
RTSR |= RTSR_ALE;
else
RTSR &= ~RTSR_ALE;
- spin_unlock_irq(&sa1100_rtc_lock);
+ spin_unlock_irq(&info->lock);
return 0;
}
@@ -170,10 +188,11 @@ static int sa1100_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm)
static int sa1100_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm)
{
+ struct sa1100_rtc *info = dev_get_drvdata(dev);
unsigned long time;
int ret;
- spin_lock_irq(&sa1100_rtc_lock);
+ spin_lock_irq(&info->lock);
ret = rtc_tm_to_time(&alrm->time, &time);
if (ret != 0)
goto out;
@@ -184,7 +203,7 @@ static int sa1100_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm)
else
RTSR &= ~RTSR_ALE;
out:
- spin_unlock_irq(&sa1100_rtc_lock);
+ spin_unlock_irq(&info->lock);
return ret;
}
@@ -211,6 +230,27 @@ static const struct rtc_class_ops sa1100_rtc_ops = {
static int sa1100_rtc_probe(struct platform_device *pdev)
{
struct rtc_device *rtc;
+ struct sa1100_rtc *info;
+ int irq_1hz, irq_alarm, ret = 0;
+
+ irq_1hz = platform_get_irq_byname(pdev, "rtc 1Hz");
+ irq_alarm = platform_get_irq_byname(pdev, "rtc alarm");
+ if (irq_1hz < 0 || irq_alarm < 0)
+ return -ENODEV;
+
+ info = kzalloc(sizeof(struct sa1100_rtc), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+ info->clk = clk_get(&pdev->dev, NULL);
+ if (IS_ERR(info->clk)) {
+ dev_err(&pdev->dev, "failed to find rtc clock source\n");
+ ret = PTR_ERR(info->clk);
+ goto err_clk;
+ }
+ info->irq_1hz = irq_1hz;
+ info->irq_alarm = irq_alarm;
+ spin_lock_init(&info->lock);
+ platform_set_drvdata(pdev, info);
/*
* According to the manual we should be able to let RTTR be zero
@@ -232,10 +272,11 @@ static int sa1100_rtc_probe(struct platform_device *pdev)
rtc = rtc_device_register(pdev->name, &pdev->dev, &sa1100_rtc_ops,
THIS_MODULE);
- if (IS_ERR(rtc))
- return PTR_ERR(rtc);
-
- platform_set_drvdata(pdev, rtc);
+ if (IS_ERR(rtc)) {
+ ret = PTR_ERR(rtc);
+ goto err_dev;
+ }
+ info->rtc = rtc;
/* Fix for a nasty initialization problem the in SA11xx RTSR register.
* See also the comments in sa1100_rtc_interrupt().
@@ -262,14 +303,24 @@ static int sa1100_rtc_probe(struct platform_device *pdev)
RTSR = RTSR_AL | RTSR_HZ;
return 0;
+err_dev:
+ platform_set_drvdata(pdev, NULL);
+ clk_put(info->clk);
+err_clk:
+ kfree(info);
+ return ret;
}
static int sa1100_rtc_remove(struct platform_device *pdev)
{
- struct rtc_device *rtc = platform_get_drvdata(pdev);
+ struct sa1100_rtc *info = platform_get_drvdata(pdev);
- if (rtc)
- rtc_device_unregister(rtc);
+ if (info) {
+ rtc_device_unregister(info->rtc);
+ clk_put(info->clk);
+ platform_set_drvdata(pdev, NULL);
+ kfree(info);
+ }
return 0;
}
@@ -277,15 +328,17 @@ static int sa1100_rtc_remove(struct platform_device *pdev)
#ifdef CONFIG_PM
static int sa1100_rtc_suspend(struct device *dev)
{
+ struct sa1100_rtc *info = dev_get_drvdata(dev);
if (device_may_wakeup(dev))
- enable_irq_wake(IRQ_RTCAlrm);
+ enable_irq_wake(info->irq_alarm);
return 0;
}
static int sa1100_rtc_resume(struct device *dev)
{
+ struct sa1100_rtc *info = dev_get_drvdata(dev);
if (device_may_wakeup(dev))
- disable_irq_wake(IRQ_RTCAlrm);
+ disable_irq_wake(info->irq_alarm);
return 0;
}
@@ -295,6 +348,13 @@ static const struct dev_pm_ops sa1100_rtc_pm_ops = {
};
#endif
+static struct of_device_id sa1100_rtc_dt_ids[] = {
+ { .compatible = "mrvl,sa1100-rtc", },
+ { .compatible = "mrvl,mmp-rtc", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, sa1100_rtc_dt_ids);
+
static struct platform_driver sa1100_rtc_driver = {
.probe = sa1100_rtc_probe,
.remove = sa1100_rtc_remove,
@@ -303,6 +363,7 @@ static struct platform_driver sa1100_rtc_driver = {
#ifdef CONFIG_PM
.pm = &sa1100_rtc_pm_ops,
#endif
+ .of_match_table = sa1100_rtc_dt_ids,
},
};
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 0b7fed746b273fb5647f5f5b05fdd7a37f9c3d76..e7feceeebc2fc9be490e3325e92f317fde5feedb 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -1508,7 +1508,7 @@ static int serial_imx_probe(struct platform_device *pdev)
ret = PTR_ERR(sport->clk);
goto unmap;
}
- clk_enable(sport->clk);
+ clk_prepare_enable(sport->clk);
sport->port.uartclk = clk_get_rate(sport->clk);
@@ -1531,8 +1531,8 @@ static int serial_imx_probe(struct platform_device *pdev)
if (pdata && pdata->exit)
pdata->exit(pdev);
clkput:
+ clk_disable_unprepare(sport->clk);
clk_put(sport->clk);
- clk_disable(sport->clk);
unmap:
iounmap(sport->port.membase);
free:
@@ -1552,11 +1552,10 @@ static int serial_imx_remove(struct platform_device *pdev)
if (sport) {
uart_remove_one_port(&imx_reg, &sport->port);
+ clk_disable_unprepare(sport->clk);
clk_put(sport->clk);
}
- clk_disable(sport->clk);
-
if (pdata && pdata->exit)
pdata->exit(pdev);
diff --git a/include/linux/platform_data/tegra_emc.h b/include/linux/platform_data/tegra_emc.h
new file mode 100644
index 0000000000000000000000000000000000000000..df67505e98f892fd225789a3a9efdb8d895e760d
--- /dev/null
+++ b/include/linux/platform_data/tegra_emc.h
@@ -0,0 +1,34 @@
+/*
+ * Copyright (C) 2011 Google, Inc.
+ *
+ * Author:
+ * Colin Cross <ccross@android.com>
+ * Olof Johansson <olof@lixom.net>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __TEGRA_EMC_H_
+#define __TEGRA_EMC_H_
+
+#define TEGRA_EMC_NUM_REGS 46
+
+struct tegra_emc_table {
+ unsigned long rate;
+ u32 regs[TEGRA_EMC_NUM_REGS];
+};
+
+struct tegra_emc_pdata {
+ int num_tables;
+ struct tegra_emc_table *tables;
+};
+
+#endif
diff --git a/include/linux/regulator/bq24022.h b/include/linux/regulator/bq24022.h
deleted file mode 100644
index a6d014005d49e6df67ded6c9b7cede3acbd40501..0000000000000000000000000000000000000000
--- a/include/linux/regulator/bq24022.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * Support for TI bq24022 (bqTINY-II) Dual Input (USB/AC Adpater)
- * 1-Cell Li-Ion Charger connected via GPIOs.
- *
- * Copyright (c) 2008 Philipp Zabel
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-struct regulator_init_data;
-
-/**
- * bq24022_mach_info - platform data for bq24022
- * @gpio_nce: GPIO line connected to the nCE pin, used to enable / disable charging
- * @gpio_iset2: GPIO line connected to the ISET2 pin, used to limit charging current to 100 mA / 500 mA
- */
-struct bq24022_mach_info {
- int gpio_nce;
- int gpio_iset2;
- struct regulator_init_data *init_data;
-};
diff --git a/sound/soc/imx/imx-audmux.c b/sound/soc/imx/imx-audmux.c
index a839494c5ea888b110e194db9dffeab31e7f1323..601df809a26a857bbcc4c007e72afcab99138fd8 100644
--- a/sound/soc/imx/imx-audmux.c
+++ b/sound/soc/imx/imx-audmux.c
@@ -80,13 +80,13 @@ static ssize_t audmux_read_file(struct file *file, char __user *user_buf,
return -ENOMEM;
if (audmux_clk)
- clk_enable(audmux_clk);
+ clk_prepare_enable(audmux_clk);
ptcr = readl(audmux_base + IMX_AUDMUX_V2_PTCR(port));
pdcr = readl(audmux_base + IMX_AUDMUX_V2_PDCR(port));
if (audmux_clk)
- clk_disable(audmux_clk);
+ clk_disable_unprepare(audmux_clk);
ret = snprintf(buf, PAGE_SIZE, "PDCR: %08x\nPTCR: %08x\n",
pdcr, ptcr);
@@ -237,13 +237,13 @@ int imx_audmux_v2_configure_port(unsigned int port, unsigned int ptcr,
return -ENOSYS;
if (audmux_clk)
- clk_enable(audmux_clk);
+ clk_prepare_enable(audmux_clk);
writel(ptcr, audmux_base + IMX_AUDMUX_V2_PTCR(port));
writel(pdcr, audmux_base + IMX_AUDMUX_V2_PDCR(port));
if (audmux_clk)
- clk_disable(audmux_clk);
+ clk_disable_unprepare(audmux_clk);
return 0;
}