ARM: at91: dt: switch to standard GPIO flag defines.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

arch/arm/boot/dts/aks-cdu.dts

@@ -46,7 +46,7 @@ macb0: ethernet@fffc4000 {
 			};
 
 			usb1: gadget@fffa4000 {
-				atmel,vbus-gpio = <&pioC 15 0>;
+				atmel,vbus-gpio = <&pioC 15 GPIO_ACTIVE_HIGH>;
 				status = "okay";
 			};
 		};
@@ -90,23 +90,23 @@ leds {
 		compatible = "gpio-leds";
 
 		red {
-			gpios = <&pioC 10 0>;
+			gpios = <&pioC 10 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "none";
 		};
 
 		green {
-			gpios = <&pioA 5 1>;
+			gpios = <&pioA 5 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 			default-state = "on";
 		};
 
 		yellow {
-			gpios = <&pioB 20 1>;
+			gpios = <&pioB 20 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
 		blue {
-			gpios = <&pioB 21 1>;
+			gpios = <&pioB 21 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 	};

arch/arm/boot/dts/animeo_ip.dts

@@ -123,7 +123,7 @@ root@2b0000 {
 
 		usb0: ohci@00500000 {
 			num-ports = <2>;
-			atmel,vbus-gpio = <&pioB 15 1>;
+			atmel,vbus-gpio = <&pioB 15 GPIO_ACTIVE_LOW>;
 			status = "okay";
 		};
 	};
@@ -133,23 +133,23 @@ leds {
 
 		power_green {
 			label = "power_green";
-			gpios = <&pioC 17 0>;
+			gpios = <&pioC 17 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		power_red {
 			label = "power_red";
-			gpios = <&pioA 2 0>;
+			gpios = <&pioA 2 GPIO_ACTIVE_HIGH>;
 		};
 
 		tx_green {
 			label = "tx_green";
-			gpios = <&pioC 19 0>;
+			gpios = <&pioC 19 GPIO_ACTIVE_HIGH>;
 		};
 
 		tx_red {
 			label = "tx_red";
-			gpios = <&pioC 18 0>;
+			gpios = <&pioC 18 GPIO_ACTIVE_HIGH>;
 		};
 	};
 
@@ -160,21 +160,21 @@ gpio_keys {
 
 		keyswitch_in {
 			label = "keyswitch_in";
-			gpios = <&pioB 1 0>;
+			gpios = <&pioB 1 GPIO_ACTIVE_HIGH>;
 			linux,code = <28>;
 			gpio-key,wakeup;
 		};
 
 		error_in {
 			label = "error_in";
-			gpios = <&pioB 2 0>;
+			gpios = <&pioB 2 GPIO_ACTIVE_HIGH>;
 			linux,code = <29>;
 			gpio-key,wakeup;
 		};
 
 		btn {
 			label = "btn";
-			gpios = <&pioC 23 0>;
+			gpios = <&pioC 23 GPIO_ACTIVE_HIGH>;
 			linux,code = <31>;
 			gpio-key,wakeup;
 		};

arch/arm/boot/dts/at91-ariag25.dts

@@ -156,7 +156,7 @@ leds {
 		/* little green LED in middle of Aria G25 module */
 		aria_led {
 			label = "aria_led";
-			gpios = <&pioB 8 0>; /* PB8 */
+			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
 			linux,default-trigger = "heartbeat";
 		};
 
@@ -164,7 +164,7 @@ aria_led {
 
 	onewire@0 {
 		compatible = "w1-gpio";
-		gpios = <&pioA 21 1>;
+		gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_w1_0>;
 	};

arch/arm/boot/dts/at91rm9200.dtsi

@@ -11,6 +11,7 @@
  */
 
 #include "skeleton.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Atmel AT91RM9200 family SoC";
@@ -503,9 +504,9 @@ nand0: nand@40000000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			nand-ecc-mode = "soft";
-			gpios = <&pioC 2 0
+			gpios = <&pioC 2 GPIO_ACTIVE_HIGH
 				 0
-				 &pioB 1 0
+				 &pioB 1 GPIO_ACTIVE_HIGH
 				>;
 			status = "disabled";
 		};
@@ -520,8 +521,8 @@ usb0: ohci@00300000 {
 
 	i2c@0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 25 0 /* sda */
-			 &pioA 26 0 /* scl */
+		gpios = <&pioA 25 GPIO_ACTIVE_HIGH /* sda */
+			 &pioA 26 GPIO_ACTIVE_HIGH /* scl */
 			>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;

arch/arm/boot/dts/at91rm9200ek.dts

@@ -50,7 +50,7 @@ macb0: ethernet@fffbc000 {
 			};
 
 			usb1: gadget@fffb0000 {
-				atmel,vbus-gpio = <&pioD 4 0>;
+				atmel,vbus-gpio = <&pioD 4 GPIO_ACTIVE_HIGH>;
 				status = "okay";
 			};
 		};
@@ -66,19 +66,19 @@ leds {
 
 		ds2 {
 			label = "green";
-			gpios = <&pioB 0 0x1>;
+			gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "mmc0";
 		};
 
 		ds4 {
 			label = "yellow";
-			gpios = <&pioB 1 0x1>;
+			gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		ds6 {
 			label = "red";
-			gpios = <&pioB 2 0x1>;
+			gpios = <&pioB 2 GPIO_ACTIVE_LOW>;
 		};
 	};
 };

arch/arm/boot/dts/at91sam9260.dtsi

@@ -9,6 +9,7 @@
  */
 
 #include "skeleton.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Atmel AT91SAM9260 family SoC";
@@ -567,8 +568,8 @@ nand0: nand@40000000 {
 			atmel,nand-cmd-offset = <22>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
-			gpios = <&pioC 13 0
-				 &pioC 14 0
+			gpios = <&pioC 13 GPIO_ACTIVE_HIGH
+				 &pioC 14 GPIO_ACTIVE_HIGH
 				 0
 				>;
 			status = "disabled";
@@ -584,8 +585,8 @@ usb0: ohci@00500000 {
 
 	i2c@0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 23 0 /* sda */
-			 &pioA 24 0 /* scl */
+		gpios = <&pioA 23 GPIO_ACTIVE_HIGH /* sda */
+			 &pioA 24 GPIO_ACTIVE_HIGH /* scl */
 			>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;

arch/arm/boot/dts/at91sam9263.dtsi

@@ -7,6 +7,7 @@
  */
 
 #include "skeleton.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Atmel AT91SAM9263 family SoC";
@@ -515,8 +516,8 @@ nand0: nand@40000000 {
 			atmel,nand-cmd-offset = <22>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
-			gpios = <&pioA 22 0
-				 &pioD 15 0
+			gpios = <&pioA 22 GPIO_ACTIVE_HIGH
+				 &pioD 15 GPIO_ACTIVE_HIGH
 				 0
 				>;
 			status = "disabled";
@@ -532,8 +533,8 @@ usb0: ohci@00a00000 {
 
 	i2c@0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioB 4 0 /* sda */
-			 &pioB 5 0 /* scl */
+		gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */
+			 &pioB 5 GPIO_ACTIVE_HIGH /* scl */
 			>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;

arch/arm/boot/dts/at91sam9263ek.dts

@@ -51,7 +51,7 @@ macb0: ethernet@fffbc000 {
 			};
 
 			usb1: gadget@fff78000 {
-				atmel,vbus-gpio = <&pioA 25 0>;
+				atmel,vbus-gpio = <&pioA 25 GPIO_ACTIVE_HIGH>;
 				status = "okay";
 			};
 
@@ -65,8 +65,8 @@ &pinctrl_mmc0_slot0_cmd_dat0
 				slot@0 {
 					reg = <0>;
 					bus-width = <4>;
-					cd-gpios = <&pioE 18 0>;
-					wp-gpios = <&pioE 19 0>;
+					cd-gpios = <&pioE 18 GPIO_ACTIVE_HIGH>;
+					wp-gpios = <&pioE 19 GPIO_ACTIVE_HIGH>;
 				};
 			};
 
@@ -141,8 +141,8 @@ data@7ca0000 {
 		usb0: ohci@00a00000 {
 			num-ports = <2>;
 			status = "okay";
-			atmel,vbus-gpio = <&pioA 24 0
-					   &pioA 21 0
+			atmel,vbus-gpio = <&pioA 24 GPIO_ACTIVE_HIGH
+					   &pioA 21 GPIO_ACTIVE_HIGH
 					  >;
 		};
 	};
@@ -152,13 +152,13 @@ leds {
 
 		d3 {
 			label = "d3";
-			gpios = <&pioB 7 0>;
+			gpios = <&pioB 7 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		d2 {
 			label = "d2";
-			gpios = <&pioC 29 1>;
+			gpios = <&pioC 29 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "nand-disk";
 		};
 	};
@@ -168,14 +168,14 @@ gpio_keys {
 
 		left_click {
 			label = "left_click";
-			gpios = <&pioC 5 1>;
+			gpios = <&pioC 5 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
 			gpio-key,wakeup;
 		};
 
 		right_click {
 			label = "right_click";
-			gpios = <&pioC 4 1>;
+			gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
 			gpio-key,wakeup;
 		};

arch/arm/boot/dts/at91sam9g20ek.dts

@@ -17,13 +17,13 @@ leds {
 
 		ds1 {
 			label = "ds1";
-			gpios = <&pioA 9 0>;
+			gpios = <&pioA 9 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		ds5 {
 			label = "ds5";
-			gpios = <&pioA 6 1>;
+			gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
 		};
 	};
 };

arch/arm/boot/dts/at91sam9g20ek_2mmc.dts

@@ -23,7 +23,7 @@ &pinctrl_mmc0_slot0_cmd_dat0
 				slot@0 {
 					reg = <0>;
 					bus-width = <4>;
-					cd-gpios = <&pioC 2 0>;
+					cd-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
 				};
 			};
 
@@ -43,13 +43,13 @@ leds {
 
 		ds1 {
 			label = "ds1";
-			gpios = <&pioB 9 0>;
+			gpios = <&pioB 9 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		ds5 {
 			label = "ds5";
-			gpios = <&pioB 8 1>;
+			gpios = <&pioB 8 GPIO_ACTIVE_LOW>;
 		};
 	};
 };

arch/arm/boot/dts/at91sam9g20ek_common.dtsi

@@ -65,7 +65,7 @@ macb0: ethernet@fffc4000 {
 			};
 
 			usb1: gadget@fffa4000 {
-				atmel,vbus-gpio = <&pioC 5 0>;
+				atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
 				status = "okay";
 			};
 
@@ -79,7 +79,7 @@ &pinctrl_mmc0_slot1_cmd_dat0
 				slot@1 {
 					reg = <1>;
 					bus-width = <4>;
-					cd-gpios = <&pioC 9 0>;
+					cd-gpios = <&pioC 9 GPIO_ACTIVE_HIGH>;
 				};
 			};
 
@@ -180,14 +180,14 @@ gpio_keys {
 
 		btn3 {
 			label = "Button 3";
-			gpios = <&pioA 30 1>;
+			gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
 			gpio-key,wakeup;
 		};
 
 		btn4 {
 			label = "Button 4";
-			gpios = <&pioA 31 1>;
+			gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
 			linux,code = <0x104>;
 			gpio-key,wakeup;
 		};

arch/arm/boot/dts/at91sam9g45.dtsi

@@ -10,6 +10,7 @@
  */
 
 #include "skeleton.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Atmel AT91SAM9G45 family SoC";
@@ -592,8 +593,8 @@ nand0: nand@40000000 {
 			atmel,nand-cmd-offset = <22>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
-			gpios = <&pioC 8 0
-				 &pioC 14 0
+			gpios = <&pioC 8 GPIO_ACTIVE_HIGH
+				 &pioC 14 GPIO_ACTIVE_HIGH
 				 0
 				>;
 			status = "disabled";
@@ -616,8 +617,8 @@ usb1: ehci@00800000 {
 
 	i2c@0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 20 0 /* sda */
-			 &pioA 21 0 /* scl */
+		gpios = <&pioA 20 GPIO_ACTIVE_HIGH /* sda */
+			 &pioA 21 GPIO_ACTIVE_HIGH /* scl */
 			>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;

arch/arm/boot/dts/at91sam9m10g45ek.dts

@@ -68,7 +68,7 @@ &pinctrl_mmc0_slot0_clk_cmd_dat0
 				slot@0 {
 					reg = <0>;
 					bus-width = <4>;
-					cd-gpios = <&pioD 10 0>;
+					cd-gpios = <&pioD 10 GPIO_ACTIVE_HIGH>;
 				};
 			};
 
@@ -81,8 +81,8 @@ &pinctrl_mmc1_slot0_clk_cmd_dat0
 				slot@0 {
 					reg = <0>;
 					bus-width = <4>;
-					cd-gpios = <&pioD 11 0>;
-					wp-gpios = <&pioD 29 0>;
+					cd-gpios = <&pioD 11 GPIO_ACTIVE_HIGH>;
+					wp-gpios = <&pioD 29 GPIO_ACTIVE_HIGH>;
 				};
 			};
 
@@ -139,8 +139,8 @@ data@4000000 {
 		usb0: ohci@00700000 {
 			status = "okay";
 			num-ports = <2>;
-			atmel,vbus-gpio = <&pioD 1 1
-					   &pioD 3 1>;
+			atmel,vbus-gpio = <&pioD 1 GPIO_ACTIVE_LOW
+					   &pioD 3 GPIO_ACTIVE_LOW>;
 		};
 
 		usb1: ehci@00800000 {
@@ -153,19 +153,19 @@ leds {
 
 		d8 {
 			label = "d8";
-			gpios = <&pioD 30 0>;
+			gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		d6 {
 			label = "d6";
-			gpios = <&pioD 0 1>;
+			gpios = <&pioD 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "nand-disk";
 		};
 
 		d7 {
 			label = "d7";
-			gpios = <&pioD 31 1>;
+			gpios = <&pioD 31 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "mmc0";
 		};
 	};
@@ -175,45 +175,45 @@ gpio_keys {
 
 		left_click {
 			label = "left_click";
-			gpios = <&pioB 6 1>;
+			gpios = <&pioB 6 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
 			gpio-key,wakeup;
 		};
 
 		right_click {
 			label = "right_click";
-			gpios = <&pioB 7 1>;
+			gpios = <&pioB 7 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
 			gpio-key,wakeup;
 		};
 
 		left {
 			label = "Joystick Left";
-			gpios = <&pioB 14 1>;
+			gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
 			linux,code = <105>;
 		};
 
 		right {
 			label = "Joystick Right";
-			gpios = <&pioB 15 1>;
+			gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
 			linux,code = <106>;
 		};
 
 		up {
 			label = "Joystick Up";
-			gpios = <&pioB 16 1>;
+			gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
 			linux,code = <103>;
 		};
 
 		down {
 			label = "Joystick Down";
-			gpios = <&pioB 17 1>;
+			gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
 			linux,code = <108>;
 		};
 
 		enter {
 			label = "Joystick Press";
-			gpios = <&pioB 18 1>;
+			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
 		};
 	};

arch/arm/boot/dts/at91sam9n12.dtsi

@@ -8,6 +8,7 @@
  */
 
 #include "skeleton.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Atmel AT91SAM9N12 SoC";
@@ -438,8 +439,8 @@ nand0: nand@40000000 {
 			atmel,nand-cmd-offset = <22>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
-			gpios = <&pioD 5 0
-				 &pioD 4 0
+			gpios = <&pioD 5 GPIO_ACTIVE_HIGH
+				 &pioD 4 GPIO_ACTIVE_HIGH
 				 0
 				>;
 			status = "disabled";
@@ -455,8 +456,8 @@ usb0: ohci@00500000 {
 
 	i2c@0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 30 0 /* sda */
-			 &pioA 31 0 /* scl */
+		gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */
+			 &pioA 31 GPIO_ACTIVE_HIGH /* scl */
 			>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;

arch/arm/boot/dts/at91sam9n12ek.dts

@@ -55,7 +55,7 @@ &pinctrl_mmc0_slot0_clk_cmd_dat0
 				slot@0 {
 					reg = <0>;
 					bus-width = <4>;
-					cd-gpios = <&pioA 7 0>;
+					cd-gpios = <&pioA 7 GPIO_ACTIVE_HIGH>;
 				};
 			};
 
@@ -95,19 +95,19 @@ leds {
 
 		d8 {
 			label = "d8";
-			gpios = <&pioB 4 1>;
+			gpios = <&pioB 4 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "mmc0";
 		};
 
 		d9 {
 			label = "d6";
-			gpios = <&pioB 5 1>;
+			gpios = <&pioB 5 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "nand-disk";
 		};
 
 		d10 {
 			label = "d7";
-			gpios = <&pioB 6 0>;
+			gpios = <&pioB 6 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
@@ -117,7 +117,7 @@ gpio_keys {
 
 		enter {
 			label = "Enter";
-			gpios = <&pioB 4 1>;
+			gpios = <&pioB 4 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
 			gpio-key,wakeup;
 		};

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -10,6 +10,7 @@
  */
 
 #include "skeleton.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Atmel AT91SAM9x5 family SoC";
@@ -664,8 +665,8 @@ nand0: nand@40000000 {
 			atmel,nand-cmd-offset = <22>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
-			gpios = <&pioD 5 0
-				 &pioD 4 0
+			gpios = <&pioD 5 GPIO_ACTIVE_HIGH
+				 &pioD 4 GPIO_ACTIVE_HIGH
 				 0
 				>;
 			status = "disabled";
@@ -688,8 +689,8 @@ usb1: ehci@00700000 {
 
 	i2c@0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 30 0 /* sda */
-			 &pioA 31 0 /* scl */
+		gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */
+			 &pioA 31 GPIO_ACTIVE_HIGH /* scl */
 			>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
@@ -703,8 +704,8 @@ &pioA 31 0 /* scl */
 
 	i2c@1 {
 		compatible = "i2c-gpio";
-		gpios = <&pioC 0 0 /* sda */
-			 &pioC 1 0 /* scl */
+		gpios = <&pioC 0 GPIO_ACTIVE_HIGH /* sda */
+			 &pioC 1 GPIO_ACTIVE_HIGH /* scl */
 			>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
@@ -718,8 +719,8 @@ &pioC 1 0 /* scl */
 
 	i2c@2 {
 		compatible = "i2c-gpio";
-		gpios = <&pioB 4 0 /* sda */
-			 &pioB 5 0 /* scl */
+		gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */
+			 &pioB 5 GPIO_ACTIVE_HIGH /* scl */
 			>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;

arch/arm/boot/dts/at91sam9x5cm.dtsi

@@ -75,19 +75,19 @@ leds {
 
 		pb18 {
 			label = "pb18";
-			gpios = <&pioB 18 1>;
+			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		pd21 {
 			label = "pd21";
-			gpios = <&pioD 21 0>;
+			gpios = <&pioD 21 GPIO_ACTIVE_HIGH>;
 		};
 	};
 
 	1wire_cm {
 		compatible = "w1-gpio";
-		gpios = <&pioB 18 0>;
+		gpios = <&pioB 18 GPIO_ACTIVE_HIGH>;
 		linux,open-drain;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_1wire_cm>;

arch/arm/boot/dts/at91sam9x5ek.dtsi

@@ -27,7 +27,7 @@ &pinctrl_mmc0_slot0_clk_cmd_dat0
 				slot@0 {
 					reg = <0>;
 					bus-width = <4>;
-					cd-gpios = <&pioD 15 0>;
+					cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
 				};
 			};
 
@@ -40,7 +40,7 @@ &pinctrl_mmc1_slot0_clk_cmd_dat0
 				slot@0 {
 					reg = <0>;
 					bus-width = <4>;
-					cd-gpios = <&pioD 14 0>;
+					cd-gpios = <&pioD 14 GPIO_ACTIVE_HIGH>;
 				};
 			};
 
@@ -86,8 +86,8 @@ m25p80@0 {
 		usb0: ohci@00600000 {
 			status = "okay";
 			num-ports = <2>;
-			atmel,vbus-gpio = <&pioD 19 1
-					   &pioD 20 1
+			atmel,vbus-gpio = <&pioD 19 GPIO_ACTIVE_LOW
+					   &pioD 20 GPIO_ACTIVE_LOW
 					  >;
 		};
 

arch/arm/boot/dts/ethernut5.dts

@@ -40,7 +40,7 @@ macb0: ethernet@fffc4000 {
 			};
 
 			usb1: gadget@fffa4000 {
-				atmel,vbus-gpio = <&pioC 5 0>;
+				atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
 				status = "okay";
 			};
 		};
@@ -52,7 +52,7 @@ nand0: nand@40000000 {
 			status = "okay";
 
 			gpios = <0
-				 &pioC 14 0
+				 &pioC 14 GPIO_ACTIVE_HIGH
 				 0
 				>;
 

arch/arm/boot/dts/evk-pro3.dts

@@ -31,7 +31,7 @@ usart2: serial@fffb8000 {
 			};
 
 			usb1: gadget@fffa4000 {
-				atmel,vbus-gpio = <&pioC 5 0>;
+				atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
 				status = "okay";
 			};