Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6

Pull device tree changes from Grant Likely:
 "Here are the DT changes I've got queued up for v3.8.  As described
  below, there are a lot of bug fixes here and documentation updates but
  nothing major:

  Bug fixes, little cleanups, and documentation changes.  The most
  invasive thing here touches a bunch of the arch directories to use a
  common build rule for .dtb files.  There are no major changes to
  functionality here other than a few new helper functions."

* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
  arm64: Fix the dtbs target building
  mtd: nand: davinci: fix the binding documentation
  rtc: rtc-mv: Add the device tree binding documentation
  devicetree/bindings: Move gpio-leds binding into leds directory
  of/vendor-prefixes: add Imagination Technologies
  microblaze: use new common dtc rule
  c6x: use new common dtc rule
  openrisc: use new common dtc rule
  arm64: Add dtbs target for building all the enabled dtb files
  arm64: use new common dtc rule
  ARM: dt: change .dtb build rules to build in dts directory
  kbuild: centralize .dts->.dtb rule
  Fix build when CONFIG_W1_MASTER_GPIO=m b exporting "allnodes"
  of/spi: Honour "status=disabled" property of device
  of_mdio: Honour "status=disabled" property of device
  of_i2c: Honour "status=disabled" property of device
  powerpc: Fix fallout from device_node->name constification
  of: add 'const' for of_parse_phandle parameter *np
  Documentation: correct of_platform_populate() argument list
  script: dtc: clean generated files
  ...

Documentation/devicetree/bindings/arm/davinci/nand.txt

@@ -23,29 +23,16 @@ Recommended properties :
 - ti,davinci-nand-buswidth: buswidth 8 or 16
 - ti,davinci-nand-use-bbt: use flash based bad block table support.
 
-Example (enbw_cmc board):
-aemif@60000000 {
-	compatible = "ti,davinci-aemif";
-	#address-cells = <2>;
-	#size-cells = <1>;
-	reg = <0x68000000 0x80000>;
-	ranges = <2 0 0x60000000 0x02000000
-		  3 0 0x62000000 0x02000000
-		  4 0 0x64000000 0x02000000
-		  5 0 0x66000000 0x02000000
-		  6 0 0x68000000 0x02000000>;
-	nand@3,0 {
-		compatible = "ti,davinci-nand";
-		reg = <3 0x0 0x807ff
-			6 0x0 0x8000>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ti,davinci-chipselect = <1>;
-		ti,davinci-mask-ale = <0>;
-		ti,davinci-mask-cle = <0>;
-		ti,davinci-mask-chipsel = <0>;
-		ti,davinci-ecc-mode = "hw";
-		ti,davinci-ecc-bits = <4>;
-		ti,davinci-nand-use-bbt;
-	};
+Example(da850 EVM ):
+nand_cs3@62000000 {
+	compatible = "ti,davinci-nand";
+	reg = <0x62000000 0x807ff
+		0x68000000 0x8000>;
+	ti,davinci-chipselect = <1>;
+	ti,davinci-mask-ale = <0>;
+	ti,davinci-mask-cle = <0>;
+	ti,davinci-mask-chipsel = <0>;
+	ti,davinci-ecc-mode = "hw";
+	ti,davinci-ecc-bits = <4>;
+	ti,davinci-nand-use-bbt;
 };

Documentation/devicetree/bindings/arm/l2cc.txt

@@ -37,7 +37,7 @@ L2: cache-controller {
         reg = <0xfff12000 0x1000>;
         arm,data-latency = <1 1 1>;
         arm,tag-latency = <2 2 2>;
-        arm,filter-latency = <0x80000000 0x8000000>;
+        arm,filter-ranges = <0x80000000 0x8000000>;
         cache-unified;
         cache-level = <2>;
 	interrupts = <45>;

Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt

+
+* Marvell MV64XXX I2C controller
+
+Required properties :
+
+ - reg             : Offset and length of the register set for the device
+ - compatible      : Should be "marvell,mv64xxx-i2c"
+ - interrupts      : The interrupt number
+ - clock-frequency : Desired I2C bus clock frequency in Hz.
+
+Examples:
+
+	i2c@11000 {
+		compatible = "marvell,mv64xxx-i2c";
+		reg = <0x11000 0x20>;
+		interrupts = <29>;
+		clock-frequency = <100000>;
+	};

Documentation/devicetree/bindings/i2c/mrvl-i2c.txt → Documentation/devicetree/bindings/i2c/i2c-pxa.txt

@@ -31,21 +31,3 @@ Examples:
 		reg = <0xd4025000 0x1000>;
 		interrupts = <58>;
 	};
-
-* Marvell MV64XXX I2C controller
-
-Required properties :
-
- - reg             : Offset and length of the register set for the device
- - compatible      : Should be "marvell,mv64xxx-i2c"
- - interrupts      : The interrupt number
- - clock-frequency : Desired I2C bus clock frequency in Hz.
-
-Examples:
-
-	i2c@11000 {
-		compatible = "marvell,mv64xxx-i2c";
-		reg = <0x11000 0x20>;
-		interrupts = <29>;
-		clock-frequency = <100000>;
-	};

Documentation/devicetree/bindings/leds/common.txt

+Common leds properties.
+
+Optional properties for child nodes:
+- label : The label for this LED.  If omitted, the label is
+  taken from the node name (excluding the unit address).
+
+- linux,default-trigger :  This parameter, if present, is a
+    string defining the trigger assigned to the LED.  Current triggers are:
+     "backlight" - LED will act as a back-light, controlled by the framebuffer
+		   system
+     "default-on" - LED will turn on (but for leds-gpio see "default-state"
+		    property in Documentation/devicetree/bindings/gpio/led.txt)
+     "heartbeat" - LED "double" flashes at a load average based rate
+     "ide-disk" - LED indicates disk activity
+     "timer" - LED flashes at a fixed, configurable rate
+
+Examples:
+
+system-status {
+	label = "Status";
+	linux,default-trigger = "heartbeat";
+	...
+};